Linux doesn’t need any drivers added. It comes with Silicon Labs USB to UART drivers already in the OS. All you have to do is add your username to the dialout group. Matter of fact there is no need to install manufacturers drivers in Windows because all they are is old versions of Silicon Labs drivers and nothing special about them.
Fred N2XK On Dec 6, 2023, at 2:26 PM, robert evans LAST_NAME via wsjt-devel <wsjt-devel@lists.sourceforge.net> wrote: An update of my windows IC-705 testing ... The asus win11 i9 laptop / WSJT-X 2.7.0-rc2 / IC-705 still was NOT decoding. Everything, including rig control, was working fine. (BTW this IC-705 firmware ver has a FT8 preset.) Installed fldigi 4.2.? that i use for nbems traffic nets for thor22 msfk Olivia etc. That worked well even made a psk31 qso. When i went back to WSJT-X 2.7.0-rc2 it started decoding just fine! And I made a couple qso on FT8 just fine. And my posts are on PSK rep as well as stations that hear me! I wonder if Icom and Yeasu will offer usb drivers for linux soon. Back to linux for now. BCNU DE N2LO~> On 12/05/2023 9:14 AM EST robert evans LAST_NAME via wsjt-devel <wsjt-devel@lists.sourceforge.net> wrote: All good suggestions. Thank You. Last night.. Double checked everything on the old dell i3 win10 and it started decoding just fine. The thing is, that it is so slow, i loose track of what i did and didn't do when i make changes. And it takes forever to reboot. I keep it around because it is about the bare minimum system to support the usb drivers now used by windows for modern radios. ft-991, ft-dx10, ic-9700, ic-705, etc. etc. etc. So, as a beta test of WSJT-X 2.7.0-rc2 on a old dell i3 win10 with the IC-705 it worked fine. Back to the asus win11 i9 laptop / IC-705 : When WSJT-X 2.7.0-rc2 did decode the dt was like 0.2 or less. I'll revisit that soon. Thanks Again. N2LO~> On 12/05/2023 3:52 AM EST Kari Sillanmäki via wsjt-devel <wsjt-devel@lists.sourceforge.net> wrote: OM, Also make sure that you are not in "Hound" mode with the "Rx All Freqs" unchecked. 73's de Kari, oh2gqc On 12/4/23 20:57, robert evans LAST_NAME via wsjt-devel wrote: Using a IC-705 over the weekend and after installing the usb drivers in a asus win11 i9 laptop i started WSJT-X 2.7.0-rc2. The rig control worked fine and the signals where being displayed in the spect graph, but no decodes. Double checked the time set. Still no decodes. Walked away for many minutes and there were decodes when i got back, but only a few. Installed WSJT-X 2.6.1 and tried again. Same behavior. Every once in a awhile it would decode a frame and then none for long periods of time even though the spectrum graph showed signals on the waterfall continuously. Switched to an old dell i3 win10 laptop and saw the same behavior with wsjt-x. Tried fldigi and it decoded Olivia and psk31 as well as cw no problem. Tried JS8 as well - no problem. Back to WSJT-X and double checked the settings. Every once in a long while it might decode what looks like a frame. N2LO~> _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/wsjt-devel _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
