a Yellow boarded Gold Card or a Red
boarded Gold Card, cos there is a difference as noted in the Qubide manual.
Ron
- Original Message -
From: Mike MacNamara [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Sunday, May 19, 2002 12:39 PM
Subject: Re: [ql-users] gold card and qubide
Hi
I
- Original Message -
From: Ron Dunnett [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Monday, May 20, 2002 9:53 PM
Subject: Re: [ql-users] gold card and qubide
Hi Mike,
Yes I'm still here, but only as an onlooker now, dont have any
QL equipment
at all now.
Nice to hear from you
I have a QPower regulator or two which were developed for the QL - £5
each
including postage if anyone is interested..
I seem to remember QPower regulators didn't work properly with Gold
Cards (OK with TrumpCard). Can't remember the reason, perhaps it was
that Gold Card needs a rapid burst of
PROTECTED]
[mailto:[EMAIL PROTECTED]]Namens Ron Dunnett
Verzonden: vrijdag 17 mei 2002 20:03
Aan: [EMAIL PROTECTED]
Onderwerp: Re: [ql-users] gold card and qubide
Remove the 68008 it is not needed anymore if you have a Gold or Super Gold
Card.
That normally cures the problem you are having.
Ron
, May 19, 2002 9:46 AM
Subject: RE: [ql-users] gold card and qubide
I did this but i still have got the same problem. I also tried
another power
supply but all i get is a blank screen after the first reset.
Could it be
the ql is not getting enough power ? Has anyone got a setup
like mine
working
In a message dated 19/05/02 19:08:23 GMT Daylight Time, [EMAIL PROTECTED] writes:
Your problem is not enough power coming out of the standard QL. Behind
the microdrives is a voltage regulator with three pins, bent over and
attached to a heat sink.
This needs a much more powerful regulator
On Sun, 19 May 2002 [EMAIL PROTECTED] wrote:
I have a QPower regulator or two which were developed for the QL - £5 each
including postage if anyone is interested..
An alternative approach, when QPower upgrades are no longer available, is
to replace the 1A 7805 with a 1.5A 7805 voltage
]]Namens Peter Fox
Verzonden: zondag 19 mei 2002 20:04
Aan: [EMAIL PROTECTED]
CC: [EMAIL PROTECTED]
Onderwerp: RE: [ql-users] gold card and qubide
In article [EMAIL PROTECTED],
[EMAIL PROTECTED]Sun, 19 May 2002 10:46:43 +0200 (henk verbeek)
wrote:
I did this but i still have got the same problem. I
PROTECTED]
Onderwerp: Re: [ql-users] gold card and qubide
Remove the 68008 it is not needed anymore if you have a Gold or Super Gold
Card.
That normally cures the problem you are having.
Ron
- Original Message -
From: henk verbeek [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent
On 19/05/02 at 19:21 Dexter wrote:
On 19 /05/02 [EMAIL PROTECTED] wrote:
I have a QPower regulator or two which were developed for the QL - £5
each including postage if anyone is interested..
An alternative approach, when QPower upgrades are no longer available, is
to replace the 1A 7805
On 19/05/02 at 20:53 henk verbeek wrote:
Thanks for all your advice but i finally got it to work. I put the qubide
and the goldcard together and got my multimeter. I measured if all the
signals from the ql expansion connector where put through the qubide to
the
gold card. I discovered this way
henk verbeek makes some magical things to make me read
} Hello everyone,
}
} I have a standard ql with a qubide and a gold card. If i connect the gold
} card or the qubide separatly they work fine but as soon as i put them
} together (quibide first and after this the gold card at the left hand
-Oorspronkelijk bericht-
Van: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]Namens Jerome Grimbert
Verzonden: vrijdag 17 mei 2002 16:37
Aan: [EMAIL PROTECTED]
Onderwerp: Re: [ql-users] gold card and qubide
henk verbeek makes some magical things to make me read
} Hello everyone,
}
} I
Remove the 68008 it is not needed anymore if you have a Gold or Super Gold
Card.
That normally cures the problem you are having.
Ron
- Original Message -
From: henk verbeek [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Friday, May 17, 2002 1:36 PM
Subject: [ql-users] gold card and
14 matches
Mail list logo