...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
Bob,
The input power was ~260W. I don't know what the R value of the
insulation is. I had the cell surrounded by high purity alumina powder
and
covered with a thin
these to determine preheating
temperatures. They may provide a cheap temperature measure for you.
Keep it shielded--good luck.
Bob
- Original Message -
FROM: Jack Cole [9]
TO: vortex-l@eskimo.com [10]
SENT:
Tuesday, March 17, 2015 9:39 AM
SUBJECT: Re: [Vo]:melted alumina tube
It is possible that the LENR reaction was not carried inside the tube in
the fuel, but in the alumina cement that covered the heater wire. The
cement must have some residual water in it. Therefore, a sonoelectrochemistry
based mechanism might be producing nanoparticles in this cement and these
notable processing steps, prior to putting them into the reactors?
Thanks for sharing, and keep up the great work!
-Bob
*From:* Jack Cole [mailto:jcol...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
Bob
mailto:jcol...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com mailto:vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
Bob,
The input power was ~260W. I don't know what the R value of
the insulation is. I had
*Sent:* Tuesday, March 17, 2015 9:39 AM
*Subject:* Re: [Vo]:melted alumina tube
To add a couple of more details. The agglomerated piece of material is
extremely hard. I tried to break it off with pliers, but it seemed like it
would take more force than to break the entire cell
@eskimo.com
*Sent:* Tuesday, March 17, 2015 9:39 AM
*Subject:* Re: [Vo]:melted alumina tube
To add a couple of more details. The agglomerated piece of material is
extremely hard. I tried to break it off with pliers, but it seemed like it
would take more force than to break the entire cell
work!
-Bob
*From:* Jack Cole [mailto:jcol...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
Bob,
The input power was ~260W. I don't know what the R value of the
insulation is. I had the cell surrounded
any other
notable processing steps, prior to putting them into the reactors?
Thanks for sharing, and keep up the great work!
-Bob
*From:* Jack Cole [mailto:jcol...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
There doesn't appear to have been any melting inside the tube. It's
interesting that the fuel formed a small diameter cylinder. There was also
a small amount of fine powder left in the cell.
The fuel is shown in the picture (looks like a little stick).
these to determine preheating temperatures. They may provide a cheap
temperature measure for you.
Keep it shielded--good luck.
Bob
- Original Message -
From: Jack Cole
To: vortex-l@eskimo.com
Sent: Tuesday, March 17, 2015 9:39 AM
Subject: Re: [Vo]:melted alumina tube
FROM: Jack
Cole [mailto:jcol...@gmail.com [4]]
SENT: Tuesday, March 17, 2015 1:08
PM
TO: vortex-l@eskimo.com [5]
SUBJECT: Re: [Vo]:melted alumina tube
Bob,
The input power was ~260W. I don't know what the R value of
the insulation is. I had the cell surrounded by high purity alumina
processing steps, prior to putting them into the reactors?
Thanks for sharing, and keep up the great work!
-Bob
*From:* Jack Cole [mailto:jcol...@gmail.com]
*Sent:* Tuesday, March 17, 2015 1:08 PM
*To:* vortex-l@eskimo.com
*Subject:* Re: [Vo]:melted alumina tube
Bob,
The input
The hydrogen combustion theory does not explain why the heat is restricted
primarily to the outside of the tube. The adulterated tube material would
have a lower melting temperature than the pure alumina powder covering.
Hydrogen that is coming from inside the tube would melt the tube as well as
*To:* vortex-l@eskimo.com
*Sent:* Tuesday, March 17, 2015 9:39 AM
*Subject:* Re: [Vo]:melted alumina tube
To add a couple of more details. The agglomerated piece of material is
extremely hard. I tried to break it off with pliers, but it seemed like it
would take more force than to break the entire
: [Vo]:melted alumina tube
Bob,
The input power was ~260W. I don't know what the R value of the insulation is.
I had the cell surrounded by high purity alumina powder and covered with a
thin sheet of ceramic insulation. I used standard 120V AC 60hz with a triac
type dimmer switch
Dear Jack,
Congratulations. Anyone that has seen a meltdown, knows that LENR is real.
Your use of a pulses current may be what caused the LENR reaction to fire
up. Current pulses might be what the key is. The triac may be producing a
periodic sharp current rise and an associated magnetic field
:* Re: [Vo]:melted alumina tube
To add a couple of more details. The agglomerated piece of material is
extremely hard. I tried to break it off with pliers, but it seemed like it
would take more force than to break the entire cell. The resistance wire
is extremely difficult to separate from
I had an interesting experiment yesterday. This was my first time using a
triac to regulate input power and sealing the tube with a compression
fitting. Unfortunately, my thermocouple failed.
Take a look at the alumina tube and the evidence for melting. The furnace
sealant which I coated it
To add a couple of more details. The agglomerated piece of material is
extremely hard. I tried to break it off with pliers, but it seemed like it
would take more force than to break the entire cell. The resistance wire
is extremely difficult to separate from the cell. I plan to open the cell
20 matches
Mail list logo
