With LNP and direct PSAP and unlimited LD etc?

From: TJ Trout 
Sent: Wednesday, September 23, 2020 2:27 PM
To: AnimalFarm Microwave Users Group 
Subject: Re: [AFMUG] OT sip question

I would have to assume doing with a national wholesale voip provider would be a 
fraction of the cost compared to a $8 flat rate per line.

On Wed, Sep 23, 2020 at 1:21 PM Lewis Bergman <[email protected]> wrote:

  Just as a clarification, FusionPBX is freeswitch not asterisk.

  On Wed, Sep 23, 2020 at 2:37 PM Daniel White <[email protected]> wrote:

    Having a direct connection for a SIP trunk is easy.  Just put an Adtran 
904e or something else into the mix.  For LNP you don't need to have the switch 
on-net... just a device in the exchange for portability and a T-1 or something 
else.

    To answer your question... CallerID manipulation is easy right now.  In 
9ish months once STIR/SHAKEN is a thing... you may run into issues getting 
calls signed with a TN for CallerID that isn't on that providers service.  

    So yes... to answer your question it is easy to do on an Asterisk based 
system (FreePBX or FusionPBX for instance) but someone like Lewis and I could 
save you a lot of trouble for certain.  That and it is easy today... but is 
going to be a lot more complicated next year.


         Daniel White
                Co-Founder 
                phone: +1 (702) 470-2770
                direct: +1 (702) 470-2766
               
         

      [email protected] 23, 2020 at 12:52
      The provider charges more for a “trunk”.
      And Lewis, I already have this service set up through them for another 
system
      We have some unique LNP porting issues and really want the voip provider 
to have a direct connection to us.  

      From: Brian Webster 
      Sent: Wednesday, September 23, 2020 12:35 PM
      To: 'AnimalFarm Microwave Users Group' 
      Subject: Re: [AFMUG] OT sip question

      It’s been a while since I have done an asterisk config but you still 
configure a SIP account much the same as you would for the ATA and it becomes a 
trunk as I recall and then you do whatever you need to with it as a single line 
trunk. Way back when I was learning it and playing I had multiple providers for 
single lines and even an IAX line too. Then I could use them as part of the 
dial plan and other features as to where it would ring and dial out.



      Thank you,

      Brian Webster

      www.wirelessmapping.com



      From: AF [mailto:[email protected]] On Behalf Of [email protected]
      Sent: Wednesday, September 23, 2020 2:01 PM
      To: [email protected]
      Subject: [AFMUG] OT sip quiestion



      If I get a voip service from some random provider and I have a sip device 
on my end, I am golden.  Say an ATA connected to a pots phone.

      Now, if I want that number to appear inside an asterisk PBX but I don’t 
want to buy a trunk, is there an easy way to do that?


--------------------------------------------------------------------------
      -- 
      AF mailing list
      [email protected]
      http://af.afmug.com/mailman/listinfo/af_af.afmug.com

      Brian WebsterSeptember 23, 2020 at 12:35
      It’s been a while since I have done an asterisk config but you still 
configure a SIP account much the same as you would for the ATA and it becomes a 
trunk as I recall and then you do whatever you need to with it as a single line 
trunk. Way back when I was learning it and playing I had multiple providers for 
single lines and even an IAX line too. Then I could use them as part of the 
dial plan and other features as to where it would ring and dial out.



      Thank you,

      Brian Webster

      www.wirelessmapping.com



      From: AF [mailto:[email protected]] On Behalf Of [email protected]
      Sent: Wednesday, September 23, 2020 2:01 PM
      To: [email protected]
      Subject: [AFMUG] OT sip quiestion



      If I get a voip service from some random provider and I have a sip device 
on my end, I am golden.  Say an ATA connected to a pots phone.

      Now, if I want that number to appear inside an asterisk PBX but I don’t 
want to buy a trunk, is there an easy way to do that?






    -- 
    AF mailing list
    [email protected]
    http://af.afmug.com/mailman/listinfo/af_af.afmug.com



  -- 

  Lewis Bergman 
  325-439-0533 Cell
  -- 
  AF mailing list
  [email protected]
  http://af.afmug.com/mailman/listinfo/af_af.afmug.com



--------------------------------------------------------------------------------
-- 
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
-- 
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com

Reply via email to