I do a private /29 for radio management and a public /30 for routing.
The key with that setup is making sure the public is the first address
on the interface making the private secondary. Not only stupid
traceroutes, but I have seen stupid routing problems without that too.
On 9/25/2015 10:09 PM, Mike Hammett wrote:
Not when you have two radios to manage in the middle.
-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
------------------------------------------------------------------------
*From: *"Eric Kuhnke" <[email protected]>
*To: *[email protected]
*Sent: *Friday, September 25, 2015 7:25:12 PM
*Subject: *Re: [AFMUG] ospf issues with pbe-5ac-500 not passing
An OSPF PTP link between two routers is usually configured as a /30 , no?
What are your MTU and other settings on the interfaces on both sides?
Other things like CDP , LDP?
On Sep 25, 2015 4:56 PM, "Tim Reichhart"
<[email protected]
<mailto:[email protected]>> wrote:
Mathew
I am running my links in PTP mode but I am splitting my backhauls
in /29 on each interface I dont know if that would cause any problems.
Tim
------------------------------------------------------------------------
-----Original Message-----
From: "Mathew Howard" <[email protected]
<mailto:[email protected]>>
To: af <[email protected] <mailto:[email protected]>>
Date: 09/25/15 11:03 AM
Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing
I didn't do anything - they just worked. Are you running them
in PTP mode, or PTMP?
On Fri, Sep 25, 2015 at 7:27 AM, Tim Reichhart
<[email protected]
<mailto:[email protected]>> wrote:
Mathew
please tell me how you got it to work because me and
justin wilson is having hell of time getting my backhaul
link to pass the ospf.
Tim
------------------------------------------------------------------------
-----Original Message-----
From: "That One Guy /sarcasm"
<[email protected]
<mailto:[email protected]>>
To: [email protected] <mailto:[email protected]>
Date: 09/25/15 12:52 AM
Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not
passing
that makes sense
On Thu, Sep 24, 2015 at 11:38 PM, Peter Kranz
<[email protected] <mailto:[email protected]>>
wrote:
Links by default now run under WDS.. So they
removed the ability to disable it.
-PK
*From:* Af [mailto:[email protected]
<mailto:[email protected]>] *On Behalf Of* That
One Guy /sarcasm
*Sent:* Thursday, September 24, 2015 9:27 PM
*To:* [email protected] <mailto:[email protected]>
*Subject:* Re: [AFMUG] ospf issues with
pbe-5ac-500 not passing
I'm poking at eoip tunnels with ospf inside
why did they remove wds?
On Thu, Sep 24, 2015 at 10:11 PM, George Skorup
<[email protected] <mailto:[email protected]>> wrote:
I don't have any of the ac radios, only M.
Does it have Multicast Data - Allow All (check
box)? If that's unchecked, then multicast will
not be allowed over the RF interface, thus
OSPF (which is multicast) will not work.
Other than that, are you sure you have MT OSPF
configured correctly? If not that, then I have
no idea. Kick it in the pants?
On 9/24/2015 9:58 PM, Tim Reichhart wrote:
so if the multicast filtering can cause
ospf not to work correctly? Even there is
no option for wds on the newer firmware?
Tim
-----Original Message-----
From: "George Skorup"
<[email protected]
<mailto:[email protected]>>
To: [email protected] <mailto:[email protected]>
Date: 09/24/15 10:53 PM
Subject: Re: [AFMUG] ospf issues with
pbe-5ac-500 not passing
Does this new 11ac stuff have
multicast filtering like the M series? I
think it's on the advanced tab. I made
that mistake once.
On 9/24/2015 9:44 PM, Rhys Cuff
(Latrobe I.T) wrote:
I find you need WDS enabled
-----Original Message-----
From: Af
[mailto:[email protected]
<mailto:[email protected]>] On
Behalf Of Tim Reichhart
Sent: Friday, 25 September 2015
12:32 PM
To: [email protected] <mailto:[email protected]>
Subject: [AFMUG] ospf issues with
pbe-5ac-500 not passing
I am having an weird issues with
my PowerBeam 5AC 500 with ospf
traffic not passing through and I
am using these PowerBeam 5AC 500
as backhauls and they are
connected to mikrotik. I am
running firmware 7.1.4xc and not
doing nbma setup.
Tim
--
If you only see yourself as part of the team but
you don't see your team as part of yourself you
have already failed as part of the team.
--
If you only see yourself as part of the team but you
don't see your team as part of yourself you have
already failed as part of the team.
