*nods* I do that as well. I keep my privates and publics in separate OSPF instances, areas, etc.
----- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com ----- Original Message ----- From: "George Skorup" <[email protected]> To: [email protected] Sent: Friday, September 25, 2015 10:28:57 PM Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing I do a private /29 for radio management and a public /30 for routing. The key with that setup is making sure the public is the first address on the interface making the private secondary. Not only stupid traceroutes, but I have seen stupid routing problems without that too. On 9/25/2015 10:09 PM, Mike Hammett wrote: Not when you have two radios to manage in the middle. ----- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com ----- Original Message ----- From: "Eric Kuhnke" <[email protected]> To: [email protected] Sent: Friday, September 25, 2015 7:25:12 PM Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing An OSPF PTP link between two routers is usually configured as a /30 , no? What are your MTU and other settings on the interfaces on both sides? Other things like CDP , LDP? On Sep 25, 2015 4:56 PM, "Tim Reichhart" < [email protected] > wrote: <blockquote> Mathew I am running my links in PTP mode but I am splitting my backhauls in /29 on each interface I dont know if that would cause any problems. Tim <blockquote> -----Original Message----- From: "Mathew Howard" < [email protected] > To: af < [email protected] > Date: 09/25/15 11:03 AM Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing I didn't do anything - they just worked. Are you running them in PTP mode, or PTMP? On Fri, Sep 25, 2015 at 7:27 AM, Tim Reichhart < [email protected] > wrote: <blockquote> Mathew please tell me how you got it to work because me and justin wilson is having hell of time getting my backhaul link to pass the ospf. Tim <blockquote> -----Original Message----- From: "That One Guy /sarcasm" < [email protected] > To: [email protected] Date: 09/25/15 12:52 AM Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing that makes sense On Thu, Sep 24, 2015 at 11:38 PM, Peter Kranz < [email protected] > wrote: <blockquote> Links by default now run under WDS.. So they removed the ability to disable it. -PK From: Af [mailto: [email protected] ] On Behalf Of That One Guy /sarcasm Sent: Thursday, September 24, 2015 9:27 PM To: [email protected] Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing I'm poking at eoip tunnels with ospf inside why did they remove wds? On Thu, Sep 24, 2015 at 10:11 PM, George Skorup < [email protected] > wrote: <blockquote> I don't have any of the ac radios, only M. Does it have Multicast Data - Allow All (check box)? If that's unchecked, then multicast will not be allowed over the RF interface, thus OSPF (which is multicast) will not work. Other than that, are you sure you have MT OSPF configured correctly? If not that, then I have no idea. Kick it in the pants? On 9/24/2015 9:58 PM, Tim Reichhart wrote: <blockquote> so if the multicast filtering can cause ospf not to work correctly? Even there is no option for wds on the newer firmware? Tim -----Original Message----- <blockquote> From: "George Skorup" < [email protected] > To: [email protected] Date: 09/24/15 10:53 PM Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing Does this new 11ac stuff have multicast filtering like the M series? I think it's on the advanced tab. I made that mistake once. On 9/24/2015 9:44 PM, Rhys Cuff (Latrobe I.T) wrote: <blockquote> I find you need WDS enabled -----Original Message----- From: Af [mailto: [email protected] ] On Behalf Of Tim Reichhart Sent: Friday, 25 September 2015 12:32 PM To: [email protected] Subject: [AFMUG] ospf issues with pbe-5ac-500 not passing I am having an weird issues with my PowerBeam 5AC 500 with ospf traffic not passing through and I am using these PowerBeam 5AC 500 as backhauls and they are connected to mikrotik. I am running firmware 7.1.4xc and not doing nbma setup. Tim </blockquote> </blockquote> </blockquote> -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team. </blockquote> -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team. </blockquote> </blockquote> </blockquote> </blockquote> </blockquote>
