I'm actually using /29s too - with both radios and the router on each end of the link in the same subnet. As far as I can remember, pretty much everything is just at the default settings.
On Fri, Sep 25, 2015 at 7:25 PM, Eric Kuhnke <[email protected]> wrote: > An OSPF PTP link between two routers is usually configured as a /30 , no? > > What are your MTU and other settings on the interfaces on both sides? > Other things like CDP , LDP? > On Sep 25, 2015 4:56 PM, "Tim Reichhart" <[email protected]> > wrote: > >> Mathew >> I am running my links in PTP mode but I am splitting my backhauls in /29 >> on each interface I dont know if that would cause any problems. >> >> Tim >> >> ------------------------------ >> -----Original Message----- >> From: "Mathew Howard" <[email protected]> >> To: af <[email protected]> >> Date: 09/25/15 11:03 AM >> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >> >> I didn't do anything - they just worked. Are you running them in PTP >> mode, or PTMP? >> >> >> On Fri, Sep 25, 2015 at 7:27 AM, Tim Reichhart < >> [email protected]> wrote: >> >>> Mathew >>> please tell me how you got it to work because me and justin wilson is >>> having hell of time getting my backhaul link to pass the ospf. >>> >>> Tim >>> >>> ------------------------------ >>> -----Original Message----- >>> From: "That One Guy /sarcasm" <[email protected]> >>> To: [email protected] >>> Date: 09/25/15 12:52 AM >>> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>> >>> that makes sense >>> >>> On Thu, Sep 24, 2015 at 11:38 PM, Peter Kranz <[email protected]> >>> wrote: >>> >>>> Links by default now run under WDS.. So they removed the ability to >>>> disable it. >>>> >>>> >>>> >>>> -PK >>>> >>>> >>>> >>>> *From:* Af [mailto:[email protected]] *On Behalf Of* That One Guy >>>> /sarcasm >>>> *Sent:* Thursday, September 24, 2015 9:27 PM >>>> *To:* [email protected] >>>> *Subject:* Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>> >>>> >>>> >>>> I'm poking at eoip tunnels with ospf inside >>>> >>>> >>>> >>>> why did they remove wds? >>>> >>>> >>>> >>>> >>>> On Thu, Sep 24, 2015 at 10:11 PM, George Skorup <[email protected]> >>>> wrote: >>>> >>>> I don't have any of the ac radios, only M. Does it have Multicast Data >>>> - Allow All (check box)? If that's unchecked, then multicast will not be >>>> allowed over the RF interface, thus OSPF (which is multicast) will not >>>> work. >>>> >>>> Other than that, are you sure you have MT OSPF configured correctly? If >>>> not that, then I have no idea. Kick it in the pants? >>>> >>>> On 9/24/2015 9:58 PM, Tim Reichhart wrote: >>>> >>>> so if the multicast filtering can cause ospf not to work correctly? >>>> Even there is no option for wds on the newer firmware? >>>> >>>> Tim >>>> >>>> -----Original Message----- >>>> >>>> From: "George Skorup" <[email protected]> >>>> To: [email protected] >>>> Date: 09/24/15 10:53 PM >>>> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>> >>>> Does this new 11ac stuff have multicast filtering like the M series? I >>>> think it's on the advanced tab. I made that mistake once. >>>> >>>> On 9/24/2015 9:44 PM, Rhys Cuff (Latrobe I.T) wrote: >>>> >>>> I find you need WDS enabled >>>> >>>> >>>> -----Original Message----- >>>> From: Af [mailto:[email protected]] On Behalf Of Tim Reichhart >>>> Sent: Friday, 25 September 2015 12:32 PM >>>> To: [email protected] >>>> Subject: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>> >>>> I am having an weird issues with my PowerBeam 5AC 500 with ospf traffic >>>> not passing through and I am using these PowerBeam 5AC 500 as backhauls and >>>> they are connected to mikrotik. I am running firmware 7.1.4xc and not doing >>>> nbma setup. >>>> >>>> Tim >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> If you only see yourself as part of the team but you don't see your >>>> team as part of yourself you have already failed as part of the team. >>>> >>>> >>>> >>> >>> >>> >>> >>> -- >>> If you only see yourself as part of the team but you don't see your team >>> as part of yourself you have already failed as part of the team. >>> >>> >>> >>> >>> >> >> >> >> >>
