I don't think any of mine have 7.1.4 on them, I think they are all either still on 7.1.1 or 7.2-beta. oh... are we talking about OSPF PTP, or the radio's PTP mode? I just have ospf setup as normal broadcast links.
On Fri, Sep 25, 2015 at 9:59 PM, Mathew Howard <[email protected]> wrote: > I'm actually using /29s too - with both radios and the router on each end > of the link in the same subnet. As far as I can remember, pretty much > everything is just at the default settings. > > On Fri, Sep 25, 2015 at 7:25 PM, Eric Kuhnke <[email protected]> > wrote: > >> An OSPF PTP link between two routers is usually configured as a /30 , no? >> >> What are your MTU and other settings on the interfaces on both sides? >> Other things like CDP , LDP? >> On Sep 25, 2015 4:56 PM, "Tim Reichhart" <[email protected]> >> wrote: >> >>> Mathew >>> I am running my links in PTP mode but I am splitting my backhauls in /29 >>> on each interface I dont know if that would cause any problems. >>> >>> Tim >>> >>> ------------------------------ >>> -----Original Message----- >>> From: "Mathew Howard" <[email protected]> >>> To: af <[email protected]> >>> Date: 09/25/15 11:03 AM >>> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>> >>> I didn't do anything - they just worked. Are you running them in PTP >>> mode, or PTMP? >>> >>> >>> On Fri, Sep 25, 2015 at 7:27 AM, Tim Reichhart < >>> [email protected]> wrote: >>> >>>> Mathew >>>> please tell me how you got it to work because me and justin wilson is >>>> having hell of time getting my backhaul link to pass the ospf. >>>> >>>> Tim >>>> >>>> ------------------------------ >>>> -----Original Message----- >>>> From: "That One Guy /sarcasm" <[email protected]> >>>> To: [email protected] >>>> Date: 09/25/15 12:52 AM >>>> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>> >>>> that makes sense >>>> >>>> On Thu, Sep 24, 2015 at 11:38 PM, Peter Kranz <[email protected]> >>>> wrote: >>>> >>>>> Links by default now run under WDS.. So they removed the ability to >>>>> disable it. >>>>> >>>>> >>>>> >>>>> -PK >>>>> >>>>> >>>>> >>>>> *From:* Af [mailto:[email protected]] *On Behalf Of* That One Guy >>>>> /sarcasm >>>>> *Sent:* Thursday, September 24, 2015 9:27 PM >>>>> *To:* [email protected] >>>>> *Subject:* Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>>> >>>>> >>>>> >>>>> I'm poking at eoip tunnels with ospf inside >>>>> >>>>> >>>>> >>>>> why did they remove wds? >>>>> >>>>> >>>>> >>>>> >>>>> On Thu, Sep 24, 2015 at 10:11 PM, George Skorup <[email protected]> >>>>> wrote: >>>>> >>>>> I don't have any of the ac radios, only M. Does it have Multicast Data >>>>> - Allow All (check box)? If that's unchecked, then multicast will not be >>>>> allowed over the RF interface, thus OSPF (which is multicast) will not >>>>> work. >>>>> >>>>> Other than that, are you sure you have MT OSPF configured correctly? >>>>> If not that, then I have no idea. Kick it in the pants? >>>>> >>>>> On 9/24/2015 9:58 PM, Tim Reichhart wrote: >>>>> >>>>> so if the multicast filtering can cause ospf not to work correctly? >>>>> Even there is no option for wds on the newer firmware? >>>>> >>>>> Tim >>>>> >>>>> -----Original Message----- >>>>> >>>>> From: "George Skorup" <[email protected]> >>>>> To: [email protected] >>>>> Date: 09/24/15 10:53 PM >>>>> Subject: Re: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>>> >>>>> Does this new 11ac stuff have multicast filtering like the M series? I >>>>> think it's on the advanced tab. I made that mistake once. >>>>> >>>>> On 9/24/2015 9:44 PM, Rhys Cuff (Latrobe I.T) wrote: >>>>> >>>>> I find you need WDS enabled >>>>> >>>>> >>>>> -----Original Message----- >>>>> From: Af [mailto:[email protected]] On Behalf Of Tim Reichhart >>>>> Sent: Friday, 25 September 2015 12:32 PM >>>>> To: [email protected] >>>>> Subject: [AFMUG] ospf issues with pbe-5ac-500 not passing >>>>> >>>>> I am having an weird issues with my PowerBeam 5AC 500 with ospf >>>>> traffic not passing through and I am using these PowerBeam 5AC 500 as >>>>> backhauls and they are connected to mikrotik. I am running firmware >>>>> 7.1.4xc >>>>> and not doing nbma setup. >>>>> >>>>> Tim >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> >>>>> If you only see yourself as part of the team but you don't see your >>>>> team as part of yourself you have already failed as part of the team. >>>>> >>>>> >>>>> >>>> >>>> >>>> >>>> >>>> -- >>>> If you only see yourself as part of the team but you don't see your >>>> team as part of yourself you have already failed as part of the team. >>>> >>>> >>>> >>>> >>>> >>> >>> >>> >>> >>> >
