Hi, It seems that the remote switch thinks that you have CIC 33 whitin the linkset, but your side configured differently. May I see your ss7.configfile?
Regards, Peter On 11/28/06, Marc Storck <[EMAIL PROTECTED]> wrote:
When the remote switch (an ericsson switch, so this is a "real" link) sends messages to me for the CIC 33 and above, I see these messages: Nov 28 17:32:48 WARNING[658]: l4isup.c:4071 l4isup_event: Received CIC=33 for unequipped circuit (typ=GRS), link 'l1'. DO you have an advise for me? Best regards, Marc Goke Aruna wrote: > I tested that config on chan_ss7 and its working fine. I dont know of libss7 > > goksie > > On 11/28/06, *Marc Storck* < [EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> wrote: > > In the mean time I tested this overhere, but with only two links (1 > link > for each linkset), only the first link has an schannel. > > Using this config the channels on l2 stay in Idle Reset pending status, > trying to block and unblock channels has the following results: > > Nov 28 16:56:39 NOTICE[5667]: l4isup.c:3598 > do_group_circuit_block_unblock: Sending CIRCUIT GROUP BLOCKING, cic=33, > mask=0x00000001. > Nov 28 16:56:39 WARNING[658]: mtp.c:1669 mtp_thread_main: No signalling > links inservice and no cluster receivers alive, dropping packet! > > Blocking and unblocking request from far end are ignored as no CICs are > assigned to linkset to which schannel from l1 is assigned. > > The ss7 driver however does not complain about the config itself, so > either the config error checking isn't checking this, or the driver > takes the binding of Schannel ==> linlkset to strictly.... > > Who can tell??? > > Thanks, > > Marc > > Goke Aruna wrote: > > yes... with chan_ss7. > > > > i have this sample and its working now. > > > > [linkset-xyz] > > enabled => yes > > enable_st => no > > use_connect => no > > hunting_policy => seq_lth > > subservice => auto > > language => en > > context => xyz-out > > > > [linkset-abc] > > enabled => yes > > enable_st => no > > use_connect => no > > hunting_policy => seq_lth > > subservice => auto > > language => en > > context => abc-out > > > > [link-l1] > > linkset => xyz > > channels => 1-15,17-31 > > schannel => 16 > > firstcic => 1 > > echocancel=allways > > echocan_taps=32 > > echocan_train=350 > > enabled => yes > > > > [link-l2] > > linkset => xyz > > channels => 1-15,17-31 > > schannel => > > firstcic => 33 > > echocancel=allways > > echocan_taps=32 > > ;echocan_train=350 > > enabled => yes > > > > [link-l3] > > linkset => abc > > channels => 1-15,17-31 > > schannel => > > firstcic => 65 > > echocancel=allways > > echocan_taps=32 > > ;echocan_train=350 > > enabled => yes > > > > [link-l4] > > linkset => abc > > channels => 1-15,17-31 > > schannel => > > firstcic => 97 > > echocancel=allways > > echocan_taps=32 > > ;echocan_train=350 > > enabled => yes > > > > [host-myhost] > > enabled => yes > > opc => 609 > > default_linkset => xyz > > dpc => xyz:223,abc:223 > > links => l1:1,l2:2,l3:3,l4:4 > > > > > > i have this ss7.conf > > > > and its working for me. > > > > that is question number 1. > > > > i think question number 2 should not be a question since u said u > used > > the two box to test before. > > > > goksie > > > > > > [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> wrote: > >> Is noone there who can answer my questions? > >> > >> :-( > >> > >> > >> On Wed, 22 Nov 2006, [EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]> wrote: > >> > >>> Hello, > >>> > >>> I have some feature-questions. > >>> > >>> 1.) > >>> I have one Asterisk Box with SS7 and 4 E1 Ports. > >>> i have one Telco with 4 Routings, a a high quality routing, a > quality > >>> Routing a cheap routing and a cheaper routing. > >>> The telco did not give me 4 SS7 Signalling Links. > >>> Is it Possible to get this running with chan_ss7 or libss7? > >>> > >>> > >>> > >>> 2.) > >>> I have 2 Asterisk boxes and one SS7-Signalling Link, is it > possible to > >>> make the signalling for the second box with the Signalling link > on the > >>> first Box? > >>> > >>> > >>> > >>> Thanks a lot for your help > >>> > >>> > >>> Nico > >>> > >>> _______________________________________________ > >>> --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > >>> > >>> asterisk-ss7 mailing list > >>> To UNSUBSCRIBE or update options visit: > >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 > <http://lists.digium.com/mailman/listinfo/asterisk-ss7> > >>> > >> _______________________________________________ > >> --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > >> > >> asterisk-ss7 mailing list > >> To UNSUBSCRIBE or update options visit: > >> http://lists.digium.com/mailman/listinfo/asterisk-ss7 > >> > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
