Hello Peter,
here is my ss7.conf
[linkset-TG1]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => even_mru
context => FROM-TG1
language => en
t35 => 4000,st
subservice => auto
[linkset-V9FF]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => even_mru
context => FROM-V9FF
language => en
t35 => 4000,st
subservice => auto
[link-l1]
linkset => TG1
channels => 2-31
schannel => 1
firstcic => 1
enabled => yes
[link-l2]
linkset => LUXV9FF
channels => 1-31
schannel =>
firstcic => 33
enabled => yes
[host-004-15-7]
enabled => yes
opc => 0x27f
default_linkset => TG1
dpc => TG1:0x108,V9FF:0x108
links => l1:1
links => l2:2
Best regards,
Marc
Peter Demeter wrote:
Hi,
It seems that the remote switch thinks that you have CIC 33 whitin the
linkset, but your side configured differently. May I see your
ss7.config file?
Regards,
Peter
On 11/28/06, *Marc Storck* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
When the remote switch (an ericsson switch, so this is a "real" link)
sends messages to me for the CIC 33 and above, I see these messages:
Nov 28 17:32:48 WARNING[658]: l4isup.c:4071 l4isup_event: Received
CIC=33 for unequipped circuit (typ=GRS), link 'l1'.
DO you have an advise for me?
Best regards,
Marc
Goke Aruna wrote:
> I tested that config on chan_ss7 and its working fine. I dont
know of libss7
>
> goksie
>
> On 11/28/06, *Marc Storck* < [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
> <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>> wrote:
>
> In the mean time I tested this overhere, but with only two
links (1
> link
> for each linkset), only the first link has an schannel.
>
> Using this config the channels on l2 stay in Idle Reset
pending status,
> trying to block and unblock channels has the following results:
>
> Nov 28 16:56:39 NOTICE[5667]: l4isup.c:3598
> do_group_circuit_block_unblock: Sending CIRCUIT GROUP
BLOCKING, cic=33,
> mask=0x00000001.
> Nov 28 16:56:39 WARNING[658]: mtp.c:1669 mtp_thread_main: No
signalling
> links inservice and no cluster receivers alive, dropping packet!
>
> Blocking and unblocking request from far end are ignored as
no CICs are
> assigned to linkset to which schannel from l1 is assigned.
>
> The ss7 driver however does not complain about the config
itself, so
> either the config error checking isn't checking this, or the
driver
> takes the binding of Schannel ==> linlkset to strictly....
>
> Who can tell???
>
> Thanks,
>
> Marc
>
> Goke Aruna wrote:
> > yes... with chan_ss7.
> >
> > i have this sample and its working now.
> >
> > [linkset-xyz]
> > enabled => yes
> > enable_st => no
> > use_connect => no
> > hunting_policy => seq_lth
> > subservice => auto
> > language => en
> > context => xyz-out
> >
> > [linkset-abc]
> > enabled => yes
> > enable_st => no
> > use_connect => no
> > hunting_policy => seq_lth
> > subservice => auto
> > language => en
> > context => abc-out
> >
> > [link-l1]
> > linkset => xyz
> > channels => 1-15,17-31
> > schannel => 16
> > firstcic => 1
> > echocancel=allways
> > echocan_taps=32
> > echocan_train=350
> > enabled => yes
> >
> > [link-l2]
> > linkset => xyz
> > channels => 1-15,17-31
> > schannel =>
> > firstcic => 33
> > echocancel=allways
> > echocan_taps=32
> > ;echocan_train=350
> > enabled => yes
> >
> > [link-l3]
> > linkset => abc
> > channels => 1-15,17-31
> > schannel =>
> > firstcic => 65
> > echocancel=allways
> > echocan_taps=32
> > ;echocan_train=350
> > enabled => yes
> >
> > [link-l4]
> > linkset => abc
> > channels => 1-15,17-31
> > schannel =>
> > firstcic => 97
> > echocancel=allways
> > echocan_taps=32
> > ;echocan_train=350
> > enabled => yes
> >
> > [host-myhost]
> > enabled => yes
> > opc => 609
> > default_linkset => xyz
> > dpc => xyz:223,abc:223
> > links => l1:1,l2:2,l3:3,l4:4
> >
> >
> > i have this ss7.conf
> >
> > and its working for me.
> >
> > that is question number 1.
> >
> > i think question number 2 should not be a question since u
said u
> used
> > the two box to test before.
> >
> > goksie
> >
> >
> > [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> <mailto:
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> wrote:
> >> Is noone there who can answer my questions?
> >>
> >> :-(
> >>
> >>
> >> On Wed, 22 Nov 2006, [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
> <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> wrote:
> >>
> >>> Hello,
> >>>
> >>> I have some feature-questions.
> >>>
> >>> 1.)
> >>> I have one Asterisk Box with SS7 and 4 E1 Ports.
> >>> i have one Telco with 4 Routings, a a high quality
routing, a
> quality
> >>> Routing a cheap routing and a cheaper routing.
> >>> The telco did not give me 4 SS7 Signalling Links.
> >>> Is it Possible to get this running with chan_ss7 or libss7?
> >>>
> >>>
> >>>
> >>> 2.)
> >>> I have 2 Asterisk boxes and one SS7-Signalling Link, is it
> possible to
> >>> make the signalling for the second box with the
Signalling link
> on the
> >>> first Box?
> >>>
> >>>
> >>>
> >>> Thanks a lot for your help
> >>>
> >>>
> >>> Nico
> >>>
> >>> _______________________________________________
> >>> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com> --
> >>>
> >>> asterisk-ss7 mailing list
> >>> To UNSUBSCRIBE or update options visit:
> >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7
> < http://lists.digium.com/mailman/listinfo/asterisk-ss7>
> >>>
> >> _______________________________________________
> >> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com> --
> >>
> >> asterisk-ss7 mailing list
> >> To UNSUBSCRIBE or update options visit:
> >> http://lists.digium.com/mailman/listinfo/asterisk-ss7
> >>
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> < http://Easynews.com> --
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-ss7
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> < http://Easynews.com> --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
>
>
>
>
------------------------------------------------------------------------
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com> --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com> --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
------------------------------------------------------------------------
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
