Marc,
Why two lines for links?
links => l1:1
links => l2:2
Please try the format what Goksie suggested:
links => l1:1,l2:2
Regards,
Peter
On 11/29/06, *Marc Storck* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
Hello Peter,
here is my ss7.conf
[linkset-TG1]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => even_mru
context => FROM-TG1
language => en
t35 => 4000,st
subservice => auto
[linkset-V9FF]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => even_mru
context => FROM-V9FF
language => en
t35 => 4000,st
subservice => auto
[link-l1]
linkset => TG1
channels => 2-31
schannel => 1
firstcic => 1
enabled => yes
[link-l2]
linkset => LUXV9FF
channels => 1-31
schannel =>
firstcic => 33
enabled => yes
[host-004-15-7]
enabled => yes
opc => 0x27f
default_linkset => TG1
dpc => TG1:0x108,V9FF:0x108
links => l1:1
links => l2:2
Best regards,
Marc
Peter Demeter wrote:
> Hi,
>
> It seems that the remote switch thinks that you have CIC 33
whitin the
> linkset, but your side configured differently. May I see your
> ss7.config file?
>
> Regards,
> Peter
>
> On 11/28/06, *Marc Storck* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
> <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>>
wrote:
>
> When the remote switch (an ericsson switch, so this is a
"real" link)
> sends messages to me for the CIC 33 and above, I see these
messages:
>
> Nov 28 17:32:48 WARNING[658]: l4isup.c:4071 l4isup_event:
Received
> CIC=33 for unequipped circuit (typ=GRS), link 'l1'.
>
> DO you have an advise for me?
>
> Best regards,
>
> Marc
>
> Goke Aruna wrote:
> > I tested that config on chan_ss7 and its working fine.
I dont
> know of libss7
> >
> > goksie
> >
> > On 11/28/06, *Marc Storck* < [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
> <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>
> > <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
<mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>>> wrote:
> >
> > In the mean time I tested this overhere, but with
only two
> links (1
> > link
> > for each linkset), only the first link has an
schannel.
> >
> > Using this config the channels on l2 stay in Idle
Reset
> pending status,
> > trying to block and unblock channels has the following
results:
> >
> > Nov 28 16:56:39 NOTICE[5667]: l4isup.c:3598
> > do_group_circuit_block_unblock: Sending CIRCUIT GROUP
> BLOCKING, cic=33,
> > mask=0x00000001.
> > Nov 28 16:56:39 WARNING[658]: mtp.c:1669
mtp_thread_main: No
> signalling
> > links inservice and no cluster receivers alive,
dropping packet!
> >
> > Blocking and unblocking request from far end are
ignored as
> no CICs are
> > assigned to linkset to which schannel from l1 is
assigned.
> >
> > The ss7 driver however does not complain about the
config
> itself, so
> > either the config error checking isn't checking this,
or the
> driver
> > takes the binding of Schannel ==> linlkset to
strictly....
> >
> > Who can tell???
> >
> > Thanks,
> >
> > Marc
> >
> > Goke Aruna wrote:
> > > yes... with chan_ss7.
> > >
> > > i have this sample and its working now.
> > >
> > > [linkset-xyz]
> > > enabled => yes
> > > enable_st => no
> > > use_connect => no
> > > hunting_policy => seq_lth
> > > subservice => auto
> > > language => en
> > > context => xyz-out
> > >
> > > [linkset-abc]
> > > enabled => yes
> > > enable_st => no
> > > use_connect => no
> > > hunting_policy => seq_lth
> > > subservice => auto
> > > language => en
> > > context => abc-out
> > >
> > > [link-l1]
> > > linkset => xyz
> > > channels => 1-15,17-31
> > > schannel => 16
> > > firstcic => 1
> > > echocancel=allways
> > > echocan_taps=32
> > > echocan_train=350
> > > enabled => yes
> > >
> > > [link-l2]
> > > linkset => xyz
> > > channels => 1-15,17-31
> > > schannel =>
> > > firstcic => 33
> > > echocancel=allways
> > > echocan_taps=32
> > > ;echocan_train=350
> > > enabled => yes
> > >
> > > [link-l3]
> > > linkset => abc
> > > channels => 1-15,17-31
> > > schannel =>
> > > firstcic => 65
> > > echocancel=allways
> > > echocan_taps=32
> > > ;echocan_train=350
> > > enabled => yes
> > >
> > > [link-l4]
> > > linkset => abc
> > > channels => 1-15,17-31
> > > schannel =>
> > > firstcic => 97
> > > echocancel=allways
> > > echocan_taps=32
> > > ;echocan_train=350
> > > enabled => yes
> > >
> > > [host-myhost]
> > > enabled => yes
> > > opc => 609
> > > default_linkset => xyz
> > > dpc => xyz:223,abc:223
> > > links => l1:1,l2:2,l3:3,l4:4
> > >
> > >
> > > i have this ss7.conf
> > >
> > > and its working for me.
> > >
> > > that is question number 1.
> > >
> > > i think question number 2 should not be a question
since u
> said u
> > used
> > > the two box to test before.
> > >
> > > goksie
> > >
> > >
> > > [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
<mailto: [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> <mailto:
> [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
<mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>> wrote:
> > >> Is noone there who can answer my questions?
> > >>
> > >> :-(
> > >>
> > >>
> > >> On Wed, 22 Nov 2006, [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
> <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>
> > <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
<mailto: [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>> wrote:
> > >>
> > >>> Hello,
> > >>>
> > >>> I have some feature-questions.
> > >>>
> > >>> 1.)
> > >>> I have one Asterisk Box with SS7 and 4 E1 Ports.
> > >>> i have one Telco with 4 Routings, a a high
quality
> routing, a
> > quality
> > >>> Routing a cheap routing and a cheaper routing.
> > >>> The telco did not give me 4 SS7 Signalling Links.
> > >>> Is it Possible to get this running with chan_ss7
or libss7?
> > >>>
> > >>>
> > >>>
> > >>> 2.)
> > >>> I have 2 Asterisk boxes and one SS7-Signalling
Link, is it
> > possible to
> > >>> make the signalling for the second box with the
> Signalling link
> > on the
> > >>> first Box?
> > >>>
> > >>>
> > >>>
> > >>> Thanks a lot for your help
> > >>>
> > >>>
> > >>> Nico
> > >>>
> > >>> _______________________________________________
> > >>> --Bandwidth and Colocation provided by
Easynews.com <http://Easynews.com>
> <http://Easynews.com>
> > <http://Easynews.com> --
> > >>>
> > >>> asterisk-ss7 mailing list
> > >>> To UNSUBSCRIBE or update options visit:
> > >>>
http://lists.digium.com/mailman/listinfo/asterisk-ss7
> > <
http://lists.digium.com/mailman/listinfo/asterisk-ss7>
> > >>>
> > >> _______________________________________________
> > >> --Bandwidth and Colocation provided by
Easynews.com <http://Easynews.com>
> < http://Easynews.com>
> > <http://Easynews.com> --
> > >>
> > >> asterisk-ss7 mailing list
> > >> To UNSUBSCRIBE or update options visit:
> > >>
http://lists.digium.com/mailman/listinfo/asterisk-ss7
> > >>
> > >
> > > _______________________________________________
> > > --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com>
> > < http://Easynews.com> --
> > >
> > > asterisk-ss7 mailing list
> > > To UNSUBSCRIBE or update options visit:
> > >
http://lists.digium.com/mailman/listinfo/asterisk-ss7
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com>
> > < http://Easynews.com> --
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> >
http://lists.digium.com/mailman/listinfo/asterisk-ss7
> >
> >
> >
> >
>
------------------------------------------------------------------------
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com> --
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-ss7
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com>
> <http://Easynews.com> --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
>
>
>
>
------------------------------------------------------------------------
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com> --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com
<http://Easynews.com> --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
<http://lists.digium.com/mailman/listinfo/asterisk-ss7>
------------------------------------------------------------------------
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
