Marc, Why two lines for links? links => l1:1 links => l2:2
Please try the format what Goksie suggested: links => l1:1,l2:2 Regards, Peter On 11/29/06, Marc Storck <[EMAIL PROTECTED]> wrote:
Hello Peter, here is my ss7.conf [linkset-TG1] enabled => yes enable_st => no use_connect => no hunting_policy => even_mru context => FROM-TG1 language => en t35 => 4000,st subservice => auto [linkset-V9FF] enabled => yes enable_st => no use_connect => no hunting_policy => even_mru context => FROM-V9FF language => en t35 => 4000,st subservice => auto [link-l1] linkset => TG1 channels => 2-31 schannel => 1 firstcic => 1 enabled => yes [link-l2] linkset => LUXV9FF channels => 1-31 schannel => firstcic => 33 enabled => yes [host-004-15-7] enabled => yes opc => 0x27f default_linkset => TG1 dpc => TG1:0x108,V9FF:0x108 links => l1:1 links => l2:2 Best regards, Marc Peter Demeter wrote: > Hi, > > It seems that the remote switch thinks that you have CIC 33 whitin the > linkset, but your side configured differently. May I see your > ss7.config file? > > Regards, > Peter > > On 11/28/06, *Marc Storck* <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> wrote: > > When the remote switch (an ericsson switch, so this is a "real" link) > sends messages to me for the CIC 33 and above, I see these messages: > > Nov 28 17:32:48 WARNING[658]: l4isup.c:4071 l4isup_event: Received > CIC=33 for unequipped circuit (typ=GRS), link 'l1'. > > DO you have an advise for me? > > Best regards, > > Marc > > Goke Aruna wrote: > > I tested that config on chan_ss7 and its working fine. I dont > know of libss7 > > > > goksie > > > > On 11/28/06, *Marc Storck* < [EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]> > > <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>> wrote: > > > > In the mean time I tested this overhere, but with only two > links (1 > > link > > for each linkset), only the first link has an schannel. > > > > Using this config the channels on l2 stay in Idle Reset > pending status, > > trying to block and unblock channels has the following results: > > > > Nov 28 16:56:39 NOTICE[5667]: l4isup.c:3598 > > do_group_circuit_block_unblock: Sending CIRCUIT GROUP > BLOCKING, cic=33, > > mask=0x00000001. > > Nov 28 16:56:39 WARNING[658]: mtp.c:1669 mtp_thread_main: No > signalling > > links inservice and no cluster receivers alive, dropping packet! > > > > Blocking and unblocking request from far end are ignored as > no CICs are > > assigned to linkset to which schannel from l1 is assigned. > > > > The ss7 driver however does not complain about the config > itself, so > > either the config error checking isn't checking this, or the > driver > > takes the binding of Schannel ==> linlkset to strictly.... > > > > Who can tell??? > > > > Thanks, > > > > Marc > > > > Goke Aruna wrote: > > > yes... with chan_ss7. > > > > > > i have this sample and its working now. > > > > > > [linkset-xyz] > > > enabled => yes > > > enable_st => no > > > use_connect => no > > > hunting_policy => seq_lth > > > subservice => auto > > > language => en > > > context => xyz-out > > > > > > [linkset-abc] > > > enabled => yes > > > enable_st => no > > > use_connect => no > > > hunting_policy => seq_lth > > > subservice => auto > > > language => en > > > context => abc-out > > > > > > [link-l1] > > > linkset => xyz > > > channels => 1-15,17-31 > > > schannel => 16 > > > firstcic => 1 > > > echocancel=allways > > > echocan_taps=32 > > > echocan_train=350 > > > enabled => yes > > > > > > [link-l2] > > > linkset => xyz > > > channels => 1-15,17-31 > > > schannel => > > > firstcic => 33 > > > echocancel=allways > > > echocan_taps=32 > > > ;echocan_train=350 > > > enabled => yes > > > > > > [link-l3] > > > linkset => abc > > > channels => 1-15,17-31 > > > schannel => > > > firstcic => 65 > > > echocancel=allways > > > echocan_taps=32 > > > ;echocan_train=350 > > > enabled => yes > > > > > > [link-l4] > > > linkset => abc > > > channels => 1-15,17-31 > > > schannel => > > > firstcic => 97 > > > echocancel=allways > > > echocan_taps=32 > > > ;echocan_train=350 > > > enabled => yes > > > > > > [host-myhost] > > > enabled => yes > > > opc => 609 > > > default_linkset => xyz > > > dpc => xyz:223,abc:223 > > > links => l1:1,l2:2,l3:3,l4:4 > > > > > > > > > i have this ss7.conf > > > > > > and its working for me. > > > > > > that is question number 1. > > > > > > i think question number 2 should not be a question since u > said u > > used > > > the two box to test before. > > > > > > goksie > > > > > > > > > [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> <mailto: > [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> wrote: > > >> Is noone there who can answer my questions? > > >> > > >> :-( > > >> > > >> > > >> On Wed, 22 Nov 2006, [EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]> > > <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> wrote: > > >> > > >>> Hello, > > >>> > > >>> I have some feature-questions. > > >>> > > >>> 1.) > > >>> I have one Asterisk Box with SS7 and 4 E1 Ports. > > >>> i have one Telco with 4 Routings, a a high quality > routing, a > > quality > > >>> Routing a cheap routing and a cheaper routing. > > >>> The telco did not give me 4 SS7 Signalling Links. > > >>> Is it Possible to get this running with chan_ss7 or libss7? > > >>> > > >>> > > >>> > > >>> 2.) > > >>> I have 2 Asterisk boxes and one SS7-Signalling Link, is it > > possible to > > >>> make the signalling for the second box with the > Signalling link > > on the > > >>> first Box? > > >>> > > >>> > > >>> > > >>> Thanks a lot for your help > > >>> > > >>> > > >>> Nico > > >>> > > >>> _______________________________________________ > > >>> --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> > > <http://Easynews.com> -- > > >>> > > >>> asterisk-ss7 mailing list > > >>> To UNSUBSCRIBE or update options visit: > > >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > < http://lists.digium.com/mailman/listinfo/asterisk-ss7> > > >>> > > >> _______________________________________________ > > >> --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> > > <http://Easynews.com> -- > > >> > > >> asterisk-ss7 mailing list > > >> To UNSUBSCRIBE or update options visit: > > >> http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > >> > > > > > > _______________________________________________ > > > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> > > < http://Easynews.com> -- > > > > > > asterisk-ss7 mailing list > > > To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> > > < http://Easynews.com> -- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > > > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com > <http://Easynews.com> -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
