On Thu, Apr 17, 2008 at 5:18 PM, Michael Buesch <[EMAIL PROTECTED]> wrote:
> [ 966.619496] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor > 0x4243) > [ 966.619496] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor > 0x4243) > [ 966.619496] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243) > [ 966.619496] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor > 0x4243) > [ 966.637500] ssb: SPROM revision 2 detected. > [ 966.658366] ssb: Sonics Silicon Backplane found on PCI device > 0000:02:05.0 > [ 966.674476] b43-phy3: Broadcom 4318 WLAN found > [ 966.714105] b43-phy3 debug: Found PHY: Analog 3, Type 2, Revision 7 > [ 966.714105] b43-phy3 debug: Found Radio: Manuf 0x17F, Version 0x2050, > Revision 8 > [ 966.734069] phy3: Selected rate control algorithm 'pid' > [ 966.736778] Broadcom 43xx driver loaded [ Features: PNR, Firmware-ID: > FW13 ] > [ 988.593922] input: b43-phy3 as /class/input/input8 > [ 987.781568] b43-phy3: Loading firmware version 351.126 (2006-07-29 > 05:54:02) > [ 987.781568] b43-phy3 warning: You are using an old firmware image. > Support for old firmware will be removed in July 2008. > [ 987.781568] b43-phy3 warning: You must go to > http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download > the latest firmware (version 4). > [ 987.895936] b43-phy3 debug: Chip initialized > [ 987.896206] b43-phy3 debug: 32-bit DMA initialized > [ 988.967223] b43-phy3 debug: Wireless interface started > [ 988.967247] b43-phy3 debug: Adding Interface type 2 > [ 988.981264] phy3: HW CONFIG: freq=2412 > [ 991.039238] b43-phy3 debug: Removing Interface type 2 > [ 991.061533] b43-phy3 debug: Wireless interface stopped > [ 990.024893] b43-phy3 debug: DMA-32 rx_ring: Used slots 0/64, Failed > frames 0/0 = 0.0%, Average tries 0.00 > [ 990.026360] b43-phy3 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, > Failed frames 0/0 = 0.0%, Average tries 0.00 > [ 990.031396] b43-phy3 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, > Failed frames 0/0 = 0.0%, Average tries 0.00 > [ 990.038040] b43-phy3 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, > Failed frames 0/0 = 0.0%, Average tries 0.00 > [ 990.048005] b43-phy3 debug: DMA-32 tx_ring_AC_VO: Used slots 0/128, > Failed frames 0/0 = 0.0%, Average tries 0.00 > [ 990.056402] b43-phy3 debug: DMA-32 tx_ring_mcast: Used slots 0/128, > Failed frames 0/0 = 0.0%, Average tries 0.00 Hmm, that looks like no data reaches the TX rings. For comparision, can you post the output of a non-Asus 4318? What happens if you flash a non-Asus SPROM into the card? -- Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
_______________________________________________ Bcm43xx-dev mailing list Bcm43xx-dev@lists.berlios.de https://lists.berlios.de/mailman/listinfo/bcm43xx-dev