Hi, Did anyone tried to work with the usb connector (the one that is marked as "usb otg"), for ethernet with 2.6.37 ? If not - maybe I should try use some older version for beagleboard ? Regards, Ran
On Thu, Jan 15, 2015 at 6:36 PM, Ran Shalit <[email protected]> wrote: > Hi Robert, > > Thanks, > I have compiled both modules and kernel, but still some error, without any > information..... > > root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod > g_ether.ko > insmod: error inserting 'g_ether.ko': -1 No such device > > The new boot log is below. > > Is there any idea why it fails ? > > Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) > Beagle Rev C5 > Reading boot sector > Loading u-boot.bin from mmc > > > U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) > > , CPU-OPP2 L3-165MHz > OMAP3 Beagle board + LPDDR/NAND > DRAM: 256 MB > NAND: 512 MiB > In: serial > Out: serial > Err: serial > Board revision Ax/Bx > Die ID #74aa000700000000015a676401014023 > Hit any key to stop autoboot: 0 > mmc1 is available > reading uImage > > 2927348 bytes read > ## Booting kernel from Legacy Image at 80300000 ... > Image Name: Linux-2.6.37 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2927284 Bytes = 2.8 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc version > 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #8 Thu Jan 15 18:29:23 IST 2015 > [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), > cr=10c53c7f > [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing > instruction cache > [ 0.000000] Machine: OMAP3 Beagle Board > [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM > [ 0.000000] Memory policy: ECC disabled, Data cache writeback > [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) > [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 64000 > [ 0.000000] Kernel command line: console=ttyO2,115200n8 > root=/dev/mmcblk0p2 rw rootwait > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 > bytes) > [ 0.000000] Memory: 252MB = 252MB total > [ 0.000000] Memory: 242712k/242712k available, 19432k reserved, 0K > highmem > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) > [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) > [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) > [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) > [ 0.000000] .text : 0xc003a000 - 0xc056e0d0 (5329 kB) > [ 0.000000] .data : 0xc0570000 - 0xc0725220 (1749 kB) > [ 0.000000] NR_IRQS:409 > [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz > [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) > [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) > [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) > [ 0.000000] Reprogramming SDRC clock to 332000000 Hz > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 > interrupts > [ 0.000000] Total of 96 interrupts on 1 active controller > [ 0.000000] GPMC revision 5.0 > [ 0.000000] Trying to install interrupt handler for IRQ402 > [ 0.000000] Trying to install interrupt handler for IRQ403 > [ 0.000000] Trying to install interrupt handler for IRQ404 > [ 0.000000] Trying to install interrupt handler for IRQ405 > [ 0.000000] Trying to install interrupt handler for IRQ406 > [ 0.000000] Trying to install interrupt handler for IRQ407 > [ 0.000000] Trying to install interrupt handler for IRQ408 > [ 0.000000] Trying to install type control for IRQ409 > [ 0.000000] Trying to set irq flags for IRQ409 > [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz > [ 0.000000] Console: colour dummy device 80x30 > [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, > Inc., Ingo Molnar > [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 > [ 0.000000] ... MAX_LOCK_DEPTH: 48 > [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 > [ 0.000000] ... CLASSHASH_SIZE: 4096 > [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 > [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 > [ 0.000000] ... CHAINHASH_SIZE: 16384 > [ 0.000000] memory used by lock dependency info: 3951 kB > [ 0.000000] per task-struct memory footprint: 2304 bytes > [ 0.000000] Calibrating delay loop... 458.96 BogoMIPS (lpj=1789952) > [ 0.000000] pid_max: default: 32768 minimum: 301 > [ 0.000000] Security Framework initialized > [ 0.000000] Mount-cache hash table entries: 512 > [ 0.000000] CPU: Testing write buffer coherency: ok > [ 0.000000] devtmpfs: initialized > [ 0.000000] regulator: core version 0.5 > [ 0.000000] regulator: dummy: > [ 0.000000] NET: Registered protocol family 16 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] OMAP GPIO hardware version 2.5 > [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 > [ 0.000000] OMAP3 Beagle Rev: C4 > [ 0.000000] Found NAND on CS0 > [ 0.000000] Registering NAND on CS0 > [ 0.000000] Unable to get DVI reset GPIO > [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. > [ 0.000000] OMAP DMA hardware revision 4.0 > [ 0.123657] bio: create slab <bio-0> at 0 > [ 0.135101] SCSI subsystem initialized > [ 0.149047] usbcore: registered new interface driver usbfs > [ 0.151000] usbcore: registered new interface driver hub > [ 0.152465] usbcore: registered new device driver usb > [ 0.159149] omap_device: omap_i2c.1: new worst case activate latency 0: > 61035 > [ 0.159362] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz > [ 0.174316] twl4030: PIH (irq 7) chaining IRQs 368..375 > [ 0.174560] twl4030: power (irq 373) chaining IRQs 376..383 > [ 0.177703] twl4030: gpio (irq 368) chaining IRQs 384..401 > [ 0.194580] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal > standby > [ 0.198181] regulator: VDAC: 1800 mV normal standby > [ 0.201873] regulator: VDVI: 1800 mV normal standby > [ 0.205810] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby > [ 0.210021] regulator: VAUX3: 1800 mV normal standby > [ 0.213623] regulator: VAUX4: 1800 mV normal standby > [ 0.214294] omap_device: omap_i2c.1: new worst case deactivate latency > 0: 91552 > [ 0.214691] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz > [ 0.229003] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz > [ 0.239440] Advanced Linux Sound Architecture Driver Version 1.0.23. > [ 0.244750] Switching to clocksource 32k_counter > [ 0.435150] musb-hdrc: version 6.0, peripheral, debug=0 > [ 0.435577] musb-hdrc musb-hdrc.0: degrade from otg to peripheral-only > mode > [ 0.435668] musb-hdrc musb-hdrc.0: dma type: dma-inventra > [ 0.435699] HS USB OTG: no transceiver configured > [ 0.435729] musb-hdrc musb-hdrc.0: musb_init_controller failed with > status -19 > [ 0.437591] NET: Registered protocol family 2 > [ 0.438537] IP route cache hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.441192] TCP established hash table entries: 8192 (order: 4, 65536 > bytes) > [ 0.441772] TCP bind hash table entries: 8192 (order: 6, 360448 bytes) > [ 0.447326] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.447509] TCP reno registered > [ 0.447540] UDP hash table entries: 128 (order: 1, 12288 bytes) > [ 0.448059] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) > [ 0.449432] NET: Registered protocol family 1 > [ 0.451385] RPC: Registered udp transport module. > [ 0.451416] RPC: Registered tcp transport module. > [ 0.451416] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.452758] NetWinder Floating Point Emulator V0.97 (double precision) > [ 0.456146] platform iva.0: Enabled OPP corresponding to 720MHz > [ 0.460144] omap-iommu omap-iommu.0: isp registered > [ 0.461303] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) > [ 0.649597] VFS: Disk quotas dquot_6.5.2 > [ 0.649780] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 0.653320] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, > Inc. > [ 0.657958] msgmni has been set to 474 > [ 0.663879] io scheduler noop registered > [ 0.663909] io scheduler deadline registered > [ 0.664184] io scheduler cfq registered (default) > [ 0.729553] OMAP DSS rev 2.0 > [ 0.730224] OMAP DISPC rev 3.0 > [ 0.730407] OMAP VENC rev 2 > [ 0.731964] OMAP DSI rev 1.0 > [ 1.061706] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > [ 1.074340] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP > UART0 > [ 1.077087] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP > UART1 > [ 1.079193] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP > UART2 > [ 1.822540] console [ttyO2] enabled > [ 1.891143] brd: module loaded > [ 1.925689] loop: module loaded > [ 1.937622] mtdoops: mtd device (mtddev=name/number) must be supplied > [ 1.944610] omap2-nand driver initializing > [ 1.949676] ONFI flash detected > [ 1.953247] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron ) > [ 1.960388] Creating 5 MTD partitions on "omap2-nand.0": > [ 1.966064] 0x000000000000-0x000000080000 : "X-Loader" > [ 1.984436] 0x000000080000-0x000000260000 : "U-Boot" > [ 1.999542] 0x000000260000-0x000000280000 : "U-Boot Env" > [ 2.014068] 0x000000280000-0x000000680000 : "Kernel" > [ 2.030242] 0x000000680000-0x000020000000 : "File System" > [ 2.301544] OneNAND driver initializing > [ 2.317413] mice: PS/2 mouse device common for all mice > [ 2.327362] input: gpio-keys as /devices/platform/gpio-keys/input/input0 > [ 2.345733] omap_device: omap_i2c.1: new worst case activate latency 0: > 122070 > [ 2.355102] input: twl4030_pwrbutton as > /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 > [ 2.374267] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 > [ 2.381378] twl_rtc twl_rtc: Power up reset detected. > [ 2.387847] twl_rtc twl_rtc: Enabling TWL-RTC. > [ 2.395385] i2c /dev entries driver > [ 2.407806] Linux media interface: v0.10 > [ 2.413055] Linux video capture interface: v2.00 > [ 2.420562] omap3isp supply VDD_CSIPHY1 not found, using dummy regulator > [ 2.427795] omap3isp supply VDD_CSIPHY2 not found, using dummy regulator > [ 2.435546] omap3isp omap3isp: Revision 2.0 found > [ 2.440887] omap-iommu omap-iommu.0: isp: version 1.1 > [ 2.552551] omap_i2c omap_i2c.2: Arbitration lost > [ 2.573242] mt9v113 2-003c: chip id mismatch read 0x0, expecting 0x2280 > [ 2.590240] isp_register_subdev_group: Unable to register subdev mt9v113 > [ 2.598937] omap_device: omap_wdt.-1: new worst case activate latency > 0: 30517 > [ 2.609344] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec > [ 2.615814] omap_device: omap_wdt.-1: new worst case deactivate latency > 0: 30517 > [ 2.625457] twl4030_wdt twl4030_wdt: Failed to register misc device > [ 2.632202] twl4030_wdt: probe of twl4030_wdt failed with error -16 > [ 2.661651] usbcore: registered new interface driver usbhid > [ 2.667602] usbhid: USB HID core driver > [ 2.679443] ALSA device list: > [ 2.682678] No soundcards found. > [ 2.686248] oprofile: hardware counters not available > [ 2.691619] oprofile: using timer interrupt. > [ 2.696716] TCP cubic registered > [ 2.700225] Initializing XFRM netlink socket > [ 2.704986] NET: Registered protocol family 17 > [ 2.709930] NET: Registered protocol family 15 > [ 2.715393] Registering the dns_resolver key type > [ 2.721282] VFP support v0.3: implementor 41 architecture 3 part 30 > variant c rev 1 > [ 2.731414] ThumbEE CPU extension supported. > [ 2.758483] Power Management for TI OMAP3. > [ 2.763824] sr_init: No PMIC hook to init smartreflex > [ 2.769836] smartreflex smartreflex.0: omap_sr_probe: SmartReflex > driver initialized > [ 2.779174] smartreflex smartreflex.1: omap_sr_probe: SmartReflex > driver initialized > [ 2.789276] SmartReflex Class3 initialized > [ 2.857177] clock: disabling unused clocks to save power > [ 2.866088] platform iva.0: omap_voltage_scale: Already at the > requestedrate 360000000 > [ 2.874511] platform mpu.0: omap_voltage_scale: Already at the > requestedrate 500000000 > [ 2.882934] platform l3_main.0: omap_voltage_scale: Already at the > requestedrate 166000000 > [ 2.927032] regulator_init_complete: incomplete constraints, leaving > VDAC on > [ 2.938446] twl_rtc twl_rtc: setting system clock to 2000-01-01 > 00:00:00 UTC (946684800) > [ 2.947753] omap_vout omap_vout: Buffer Size = 3686400 > [ 2.957153] omap_vout omap_vout: : registered and initialized video > device 15 > [ 2.964782] omap_vout omap_vout: Buffer Size = 3686400 > [ 2.973541] omap_vout omap_vout: : registered and initialized video > device 16 > [ 2.988342] Waiting for root device /dev/mmcblk0p2... > [ 3.141418] mmc0: new high speed SDHC card at address aaaa > [ 3.151336] mmcblk0: mmc0:aaaa SU16G 14.8 GiB > [ 3.175750] mmcblk0: p1 p2 > [ 3.218505] EXT3-fs: barriers not enabled > [ 3.227325] kjournald starting. Commit interval 5 seconds > [ 3.233612] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, > running e2fsck is recommended > [ 3.247222] EXT3-fs (mmcblk0p2): using internal journal > [ 3.252807] EXT3-fs (mmcblk0p2): recovery complete > [ 3.258544] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data > mode > [ 3.266540] VFS: Mounted root (ext3 filesystem) on device 179:2. > [ 3.273132] Freeing init memory: 200K > Failed to open /dev/kmsg for logging: No such file or directory > [ 3.609405] <30>systemd[1]: systemd 37 running in system mode. (+PAM > +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) > > Welcome to The ֵngstrצm Distribution! > > [ 3.713439] <28>systemd[1]: /sbin/modprobe failed with error code 1. > [ 3.724670] <30>systemd[1]: Set hostname to <beagleboard>. > Starting Runtime Directory... > Starting Remount API VFS... > Starting Lock Directory... > Starting Media Directory... > Started Apply Kernel Variables [ > OK ] > Started Huge Pages File System [ > OK ] > Starting POSIX Message Queue File System... > Starting File System Check on Root Device... > Started Load Kernel Modules [ > OK ] > Started Configuration File System [ > OK ] > Started FUSE Control File System [ > OK ] > Started Set Up Additional Binary Formats [ > OK ] > [ 4.677764] <30>systemd-fsck[593]: Root directory is writable, skipping > check. > Starting Debug File System... > Started Security File System [ > OK ] > Starting Syslog Kernel Log Buffer Bridge... > Started Syslog Kernel Log Buffer Bridge [ > OK ] > Starting udev Coldplug all Devices... > Starting udev Kernel Device Manager... > Started Runtime Directory [ > OK ] > Started Remount API VFS [ > OK ] > Started Lock Directory [ > OK ] > Started udev Ker[ 5.031005] <30>udevd[600]: starting version 175 > nel Device Manager [ OK ] > Started Media Directory [ > OK ] > Started POSIX Message Queue File System [ > OK ] > Started File System Check on Root Device [ > OK ] > Started Debug File System [ > OK ] > Starting Remount Root FS... > Starting STDOUT Syslog Bridge... > Started STDOUT Syslog Bridge [ > OK ] > Started Remount Root FS [ > OK ] > Started Opkg first boot configure [ > OK ] > Starting /tmp... > Started Machine ID first boot configure [ > OK ] > Started /tmp [ > OK ] > Starting Load Random Seed... > Starting Recreate Volatile Files and Directories... > Started Load Random Seed [ > OK ] > Started Recreate Volatile Files and Directories [ > OK ] > Starting Console System Startup Logging... > Starting xinetd.service... > Started Angstrom LED config [ > OK ] > Starting Timestamping service... > Started Timestamping service [ > OK ] > Starting Network Manager... > Started SSH Key Generation [ > OK ] > Starting System Logging Service... > Starting Permit User Sessions... > Starting Login Service... > Starting Avahi mDNS/DNS-SD Stack... > Starting Periodic Command Scheduler... > Started Periodic Command Scheduler [ > OK ] > Starting internet superserver: xinetdStarting D-Bus System Message Bus... > Starting Disk Manager... > Started Console System Startup Logging [ > OK ] > [ 8.354309] <27>systemd-logind[707]: Failed to open > /sys/class/tty/tty0/active: No such file or directory > Started Permit User Sessions [ > OK ] > [ 8.659515] <27>systemd-logind[707]: Failed to fully start up daemon: > No such file or directory > [ 8.877380] <29>systemd[1]: systemd-logind.service: main process > exited, code=exited, status=1 > [ 9.057952] <75>/usr/sbin/crond[722]: (CRON) INFO (Syslog will be used > instead of sendmail.): No such file or directory > . > Failed to start Login Service > [FAILED] > [ 9.415985] <30>avahi-daemon[711]: Found user 'avahi' (UID 998) and > group 'avahi' (GID 996). > [ 9.478942] <30>avahi-daemon[711]: Successfully dropped root privileges. > See 'systemctl status systemd-logind.service' for details. > [ 9.517791] <29>systemd[1]: Unit systemd-logind.service entered failed > state. > [ 9.659942] <30>avahi-daemon[711]: avahi-daemon 0.6.30 starting up. > Started xinetd.service [ > OK ] > [ 9.930999] <26>xinetd[868]: 868 {init_services} no services. Exiting... > Starting Serial Getty on ttyO2... > [ 10.786376] <30>NetworkManager[704]: NetworkManager[704]: <info> > NetworkManager (version 0.9.2.0) is starting... > Started Serial Getty on ttyO2 [ > OK ] > [ 11.033538] <30>udisks-daemon[770]: (process:770): GLib-WARNING **: > goption.c:2168: ignoring no-arg, optional-arg or filename flags (16) on > option of type 1 > [ 11.310058] <14>NetworkManager[704]: <info> NetworkManager (version > 0.9.2.0) is starting... > Started D-Bus System Message Bus [ > OK ] > [ 11.474243] <30>NetworkManager[704]: NetworkManager[704]: <info> Read > config file (null) > [ 11.721771] <14>NetworkManager[704]: <info> Read config file (null) > [ 11.728485] <30>load-timestamp.sh[702]: Update systemtime from > /etc/timestamp > [ 12.190551] <30>load-timestamp.sh[702]: Thu Jan 12 12:19:00 UTC 2012 > [ 12.656372] <27>systemd-uaccess[1031]: Failed to apply ACL on > /dev/v4l-subdev3: Operation not supported > [ 12.891265] <27>systemd-uaccess[1027]: Failed to apply ACL on > /dev/v4l-subdev0: Operation not supported > > .---O---. [ 13.117218] > <27>systemd-uaccess[1019]: Failed to apply ACL on /dev/v4l-subdev1: > Operation not supported > > | | .-. o o > | | |-----.-----.-[ 13.337951] <27>systemd-uaccess[1033]: Failed to > apply ACL on /dev/v4l-subdev2: Operation not supported > ----.| | .----..--[ 13.378295] <27>systemd-uaccess[1037]: Failed to > apply ACL on /dev/v4l-subdev6: Operation not supported > ---.-----. > | | | __ | ---'| '--.| .-'| | | > | | | | | |--- [ 13.526580] <27>systemd-uaccess[1040]: Failed > to apply ACL on /dev/v4l-subdev7: Operation not supported > || --'| | | ' | | | | > '---'---'--'--'--. |-----''----''--' '-----'-'-'-' > [ 13.677337] <27>systemd-uaccess[1028]: Failed to apply ACL on > /dev/v4l-subdev5: Operation not supported > -' | > '---' > > The Angstrom Distribution beagleboard ttyO2 > > Angstrom v2012.01-co[ 13.979644] <27>systemd-uaccess[1042]: Failed to > apply ACL on /dev/v4l-subdev4: Operation not supported > re - Kernel 2.6.37 > > beagleboard login: [ 14.332580] <27>systemd-uaccess[1049]: Failed to > apply ACL on /dev/video0: Operation not supported > [ 14.667114] <27>systemd-uaccess[1051]: Failed to apply ACL on > /dev/video1: Operation not supported > [ 14.995208] <27>systemd-uaccess[1053]: Failed to apply ACL on > /dev/video3: Operation not supported > Started udev Coldplug all Devices [ > OK ] > > [ 15.218170] <27>systemd-uaccess[1055]: Failed to apply ACL on > /dev/video2: Operation not supported > [ 15.450988] <27>systemd-uaccess[1057]: Failed to apply ACL on > /dev/video4: Operation not supported > Started Disk Manager [ > OK ] > > Started Avahi mDNS/DNS-SD Stack > [[ 15.689880] <27> OK ] > systemd-uaccess[1063]: Failed to apply ACL on > /dev/video5: Operation not supported > [ 15.800720] <27>systemd-uaccess[1073]: Failed to apply ACL on > /dev/video8: Operation not supported > [ 16.030517] <27>systemd-uaccess[1072]: Failed to apply ACL on > /dev/video7: Operation not supported > [ 16.091583] <27>systemd-uaccess[1086]: Failed to apply ACL on > /dev/video6: Operation not supported > Stopping Syslog Kernel Log Buffer Bridge... > [ 16.201354] > <30>udisks-daemon[770]: (udisks-daemon:770): udisks-daemon-DEBUG: Starting > daemon version 1.0.4 > [ 16.326660] <30>avahi-daemon[711]: Successfully called chroot(). > [ 16.400512] <30>avahi-daemon[711]: Successfully dropped remaining > capabilities. > [ 16.473449] <30>avahi-daemon[711]: Loading service file > /services/sftp-ssh.service. > [ 16.510803] <30>avahi-daemon[711]: Loading service file > /services/ssh.service. > [ 16.565338] <30>avahi-daemon[711]: Loading service file > /services/udisks.service. > [ 16.644561] <30>avahi-daemon[711]: Network interface enumeration > completed. > [ 16.669464] <30>avahi-daemon[711]: Registering HINFO record with values > 'ARMV7L'/'LINUX'. > [ 16.757904] <30>avahi-daemon[711]: Server startup complete. Host name > is beagleboard.local. Local service cookie is 441939348. > Starting Getty on tty1... > [ 16.862426] <30>avahi-daemon[711]: Service > "beagleboard" (/services/udisks.service) successfully established. > [ 16.971832] <30>dbus-daemon[969]: dbus[969]: [system] Activating > service name='org.freedesktop.PolicyKit1' (using servicehelper) > Started Getty on tty1 [ > OK ] > > [ 17.104522] <29>dbus[969]: [system] Activating service > name='org.freedesktop.PolicyKit1' (using servicehelper) > [ 17.218292] <30>avahi-daemon[711]: Service "beagleboard" > (/services/ssh.service) successfully established. > Starting Gnome D[ 17.271667] <27>isplay Manager..systemd-uaccess. > [1199]: > Failed to apply ACL on /dev/snd/timer: Operation not supported > [ 17.293273] <30>avahi-daemon[711]: Service "beagleboard" > (/services/sftp-ssh.service) successfully established. > Started Gnome Display Manager [ > OK ] > > Stopped Syslog Kernel Log Buffer Bridge > [ OK ] > > Started System Logging Service > [ OK ] > > Started Network Manager > [ OK ] > > .---O---. > | | .-. o o > | | |-----.-----.-----.| | .----..-----.-----. > | | | __ | ---'| '--.| .-'| | | > | | | | | |--- || --'| | | ' | | | | > '---'---'--'--'--. |-----''----''--' '-----'-'-'-' > -' | > '---' > > The Angstrom Distribution beagleboard ttyO2 > > Angstrom v2012.01-core - Kernel 2.6.37 > > beagleboard login: > .---O---. > | | .-. o o > | | |-----.-----.-----.| | .----..-----.-----. > | | | __ | ---'| '--.| .-'| | | > | | | | | |--- || --'| | | ' | | | | > '---'---'--'--'--. |-----''----''--' '-----'-'-'-' > -' | > '---' > > The Angstrom Distribution beagleboard ttyO2 > > Angstrom v2012.01-core - Kernel 2.6.37 > > beagleboard login: root > Last login: Thu Jan 12 12:19:48 GMT 2012 on ttyO2 > root@beagleboard:~# > root@beagleboard:~# > root@beagleboard:~# cd /lib/modules/2.6.37/kernel/drivers/usb/gadget/ > root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod > g_ether.ko > insmod: error inserting 'g_ether.ko': -1 No such device > root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget > > Regards, > Ran > > > On Thu, Jan 15, 2015 at 6:26 PM, Robert Nelson <[email protected]> > wrote: > >> On Thu, Jan 15, 2015 at 10:23 AM, Ran Shalit <[email protected]> wrote: >> > Hi Robert, >> > >> > Thank you very much. >> > I was lazy not to notice that.... >> > It now seems better (less errors on boot), but still fails with same >> error: >> > insmod: error inserting 'g_ether.ko': -1 No such device >> > Can you give me another hint what might cause such failure? >> > >> > This is the boot log: >> > >> > Last login: Thu Jan 12 12:31:58 GMT 2012 on ttyO2 >> > root@beagleboard:~# >> > root@beagleboard:~# >> > root@beagleboard:~# >> > root@beagleboard:~# modprobe g_ether >> > [ 30.667053] g_ether: disagrees about version of symbol module_layout >> > FATAL: Error inserting g_ether >> >> This means your kernel was built seperatly from the modules.. >> >> When you build your kernel, just also build 'make modules' and install >> them to the rootfs.. >> >> >> > (/lib/modules/2.6.37/kernel/drivers/usb/gadget/g_ether.ko): Invalid >> module >> > format >> > root@beagleboard:~# d >> > >> > Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >> > Beagle Rev C5 >> > Reading boot sector >> > Loading u-boot.bin from mmc >> > >> > >> > U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >> > >> > , CPU-OPP2 L3-165MHz >> > OMAP3 Beagle board + LPDDR/NAND >> > DRAM: 256 MB >> > NAND: 512 MiB >> > In: serial >> > Out: serial >> > Err: serial >> > Board revision Ax/Bx >> > Die ID #74aa000700000000015a676401014023 >> > Hit any key to stop autoboot: 0 >> > mmc1 is available >> > reading uImage >> > >> > 2918324 bytes read >> > ## Booting kernel from Legacy Image at 80300000 ... >> > Image Name: Linux-2.6.37 >> > Image Type: ARM Linux Kernel Image (uncompressed) >> > Data Size: 2918260 Bytes = 2.8 MB >> > Load Address: 80008000 >> > Entry Point: 80008000 >> > Verifying Checksum ... OK >> > Loading Kernel Image ... OK >> > OK >> > >> > Starting kernel ... >> > >> > Uncompressing Linux... done, booting the kernel. >> > [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc version >> > 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #7 Thu Jan 15 18:09:40 IST 2015 >> > [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >> > cr=10c53c7f >> > [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >> > instruction cache >> > [ 0.000000] Machine: OMAP3 Beagle Board >> > [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >> > [ 0.000000] Memory policy: ECC disabled, Data cache writeback >> > [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) >> > [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 >> > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >> Total >> > pages: 64000 >> > [ 0.000000] Kernel command line: console=ttyO2,115200n8 >> > root=/dev/mmcblk0p2 rw rootwait >> > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >> > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 >> > bytes) >> > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >> bytes) >> > [ 0.000000] Memory: 252MB = 252MB total >> > [ 0.000000] Memory: 242740k/242740k available, 19404k reserved, 0K >> > highmem >> > [ 0.000000] Virtual kernel memory layout: >> > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >> > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >> > [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >> > [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >> > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >> > [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >> > [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >> > [ 0.000000] .text : 0xc003a000 - 0xc0568f4c (5308 kB) >> > [ 0.000000] .data : 0xc056a000 - 0xc071f1a0 (1749 kB) >> > [ 0.000000] NR_IRQS:409 >> > [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >> > [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >> > [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >> > [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >> > [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >> > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >> > interrupts >> > [ 0.000000] Total of 96 interrupts on 1 active controller >> > [ 0.000000] GPMC revision 5.0 >> > [ 0.000000] Trying to install interrupt handler for IRQ402 >> > [ 0.000000] Trying to install interrupt handler for IRQ403 >> > [ 0.000000] Trying to install interrupt handler for IRQ404 >> > [ 0.000000] Trying to install interrupt handler for IRQ405 >> > [ 0.000000] Trying to install interrupt handler for IRQ406 >> > [ 0.000000] Trying to install interrupt handler for IRQ407 >> > [ 0.000000] Trying to install interrupt handler for IRQ408 >> > [ 0.000000] Trying to install type control for IRQ409 >> > [ 0.000000] Trying to set irq flags for IRQ409 >> > [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >> > [ 0.000000] Console: colour dummy device 80x30 >> > [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >> Inc., >> > Ingo Molnar >> > [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >> > [ 0.000000] ... MAX_LOCK_DEPTH: 48 >> > [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >> > [ 0.000000] ... CLASSHASH_SIZE: 4096 >> > [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >> > [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >> > [ 0.000000] ... CHAINHASH_SIZE: 16384 >> > [ 0.000000] memory used by lock dependency info: 3951 kB >> > [ 0.000000] per task-struct memory footprint: 2304 bytes >> > [ 0.000000] Calibrating delay loop... 456.86 BogoMIPS (lpj=1781760) >> > [ 0.000000] pid_max: default: 32768 minimum: 301 >> > [ 0.000000] Security Framework initialized >> > [ 0.000000] Mount-cache hash table entries: 512 >> > [ 0.000000] CPU: Testing write buffer coherency: ok >> > [ 0.000000] devtmpfs: initialized >> > [ 0.000000] regulator: core version 0.5 >> > [ 0.000000] regulator: dummy: >> > [ 0.000000] NET: Registered protocol family 16 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] OMAP GPIO hardware version 2.5 >> > [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >> > [ 0.000000] OMAP3 Beagle Rev: C4 >> > [ 0.000000] Found NAND on CS0 >> > [ 0.000000] Registering NAND on CS0 >> > [ 0.000000] Unable to get DVI reset GPIO >> > [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >> > [ 0.000000] OMAP DMA hardware revision 4.0 >> > [ 0.122314] bio: create slab <bio-0> at 0 >> > [ 0.133697] SCSI subsystem initialized >> > [ 0.147491] usbcore: registered new interface driver usbfs >> > [ 0.149322] usbcore: registered new interface driver hub >> > [ 0.150878] usbcore: registered new device driver usb >> > [ 0.157501] omap_device: omap_i2c.1: new worst case activate latency >> 0: >> > 30517 >> > [ 0.157684] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >> > [ 0.172485] twl4030: PIH (irq 7) chaining IRQs 368..375 >> > [ 0.172729] twl4030: power (irq 373) chaining IRQs 376..383 >> > [ 0.175842] twl4030: gpio (irq 368) chaining IRQs 384..401 >> > [ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >> standby >> > [ 0.196044] regulator: VDAC: 1800 mV normal standby >> > [ 0.199615] regulator: VDVI: 1800 mV normal standby >> > [ 0.203613] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >> standby >> > [ 0.207763] regulator: VAUX3: 1800 mV normal standby >> > [ 0.211334] regulator: VAUX4: 1800 mV normal standby >> > [ 0.211914] omap_device: omap_i2c.1: new worst case deactivate >> latency 0: >> > 61035 >> > [ 0.221954] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >> > [ 0.236083] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >> > [ 0.246398] Advanced Linux Sound Architecture Driver Version 1.0.23. >> > [ 0.251586] Switching to clocksource 32k_counter >> > [ 0.440246] musb-hdrc: version 6.0, peripheral, debug=0 >> > [ 0.440673] musb-hdrc musb-hdrc.0: degrade from otg to >> peripheral-only >> > mode >> > [ 0.440795] musb-hdrc musb-hdrc.0: dma type: dma-inventra >> > [ 0.440826] HS USB OTG: no transceiver configured >> > [ 0.440856] musb-hdrc musb-hdrc.0: musb_init_controller failed with >> > status -19 >> > [ 0.442718] NET: Registered protocol family 2 >> > [ 0.443664] IP route cache hash table entries: 2048 (order: 1, 8192 >> > bytes) >> > [ 0.446136] TCP established hash table entries: 8192 (order: 4, 65536 >> > bytes) >> > [ 0.446746] TCP bind hash table entries: 8192 (order: 6, 360448 >> bytes) >> > [ 0.452423] TCP: Hash tables configured (established 8192 bind 8192) >> > [ 0.452545] TCP reno registered >> > [ 0.452606] UDP hash table entries: 128 (order: 1, 12288 bytes) >> > [ 0.453033] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) >> > [ 0.454437] NET: Registered protocol family 1 >> > [ 0.456481] RPC: Registered udp transport module. >> > [ 0.456512] RPC: Registered tcp transport module. >> > [ 0.456542] RPC: Registered tcp NFSv4.1 backchannel transport module. >> > [ 0.457855] NetWinder Floating Point Emulator V0.97 (double >> precision) >> > [ 0.461059] platform iva.0: Enabled OPP corresponding to 720MHz >> > [ 0.465179] omap-iommu omap-iommu.0: isp registered >> > [ 0.466308] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >> > [ 0.654205] VFS: Disk quotas dquot_6.5.2 >> > [ 0.654388] Dquot-cache hash table entries: 1024 (order 0, 4096 >> bytes) >> > [ 0.657714] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, >> > Inc. >> > [ 0.659271] msgmni has been set to 474 >> > [ 0.665100] io scheduler noop registered >> > [ 0.665191] io scheduler deadline registered >> > [ 0.665435] io scheduler cfq registered (default) >> > [ 0.728576] OMAP DSS rev 2.0 >> > [ 0.729248] OMAP DISPC rev 3.0 >> > [ 0.729431] OMAP VENC rev 2 >> > [ 0.730957] OMAP DSI rev 1.0 >> > [ 1.060791] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >> > [ 1.073242] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >> OMAP >> > UART0 >> > [ 1.076141] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >> OMAP >> > UART1 >> > [ 1.078155] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >> OMAP >> > UART2 >> > [ 1.821472] console [ttyO2] enabled >> > [ 1.889343] brd: module loaded >> > [ 1.923370] loop: module loaded >> > [ 1.935363] mtdoops: mtd device (mtddev=name/number) must be supplied >> > [ 1.942352] omap2-nand driver initializing >> > [ 1.947479] ONFI flash detected >> > [ 1.951019] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc >> (Micron ) >> > [ 1.958160] Creating 5 MTD partitions on "omap2-nand.0": >> > [ 1.963836] 0x000000000000-0x000000080000 : "X-Loader" >> > [ 1.982055] 0x000000080000-0x000000260000 : "U-Boot" >> > [ 1.997100] 0x000000260000-0x000000280000 : "U-Boot Env" >> > [ 2.011535] 0x000000280000-0x000000680000 : "Kernel" >> > [ 2.027618] 0x000000680000-0x000020000000 : "File System" >> > [ 2.298248] OneNAND driver initializing >> > [ 2.315246] mice: PS/2 mouse device common for all mice >> > [ 2.324920] input: gpio-keys as >> /devices/platform/gpio-keys/input/input0 >> > [ 2.343780] omap_device: omap_i2c.1: new worst case activate latency >> 0: >> > 91552 >> > [ 2.352966] input: twl4030_pwrbutton as >> > >> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >> > [ 2.372009] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >> > [ 2.379119] twl_rtc twl_rtc: Power up reset detected. >> > [ 2.385589] twl_rtc twl_rtc: Enabling TWL-RTC. >> > [ 2.393066] i2c /dev entries driver >> > [ 2.405456] Linux media interface: v0.10 >> > [ 2.410736] Linux video capture interface: v2.00 >> > [ 2.418273] omap3isp supply VDD_CSIPHY1 not found, using dummy >> regulator >> > [ 2.425506] omap3isp supply VDD_CSIPHY2 not found, using dummy >> regulator >> > [ 2.433227] omap3isp omap3isp: Revision 2.0 found >> > [ 2.438476] omap-iommu omap-iommu.0: isp: version 1.1 >> > [ 2.559204] omap_i2c omap_i2c.2: Arbitration lost >> > [ 2.580078] mt9v113 2-003c: chip id mismatch read 0x0, expecting >> 0x2280 >> > [ 2.597198] isp_register_subdev_group: Unable to register subdev >> mt9v113 >> > [ 2.605865] omap_device: omap_wdt.-1: new worst case activate >> latency 0: >> > 30517 >> > [ 2.616241] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> > [ 2.622711] omap_device: omap_wdt.-1: new worst case deactivate >> latency >> > 0: 30517 >> > [ 2.632354] twl4030_wdt twl4030_wdt: Failed to register misc device >> > [ 2.639099] twl4030_wdt: probe of twl4030_wdt failed with error -16 >> > [ 2.668334] usbcore: registered new interface driver usbhid >> > [ 2.674285] usbhid: USB HID core driver >> > [ 2.686126] ALSA device list: >> > [ 2.689392] No soundcards found. >> > [ 2.692962] oprofile: hardware counters not available >> > [ 2.698333] oprofile: using timer interrupt. >> > [ 2.703430] TCP cubic registered >> > [ 2.706939] Initializing XFRM netlink socket >> > [ 2.711639] NET: Registered protocol family 17 >> > [ 2.716613] NET: Registered protocol family 15 >> > [ 2.722045] Registering the dns_resolver key type >> > [ 2.727783] VFP support v0.3: implementor 41 architecture 3 part 30 >> > variant c rev 1 >> > [ 2.737945] ThumbEE CPU extension supported. >> > [ 2.764984] Power Management for TI OMAP3. >> > [ 2.770355] sr_init: No PMIC hook to init smartreflex >> > [ 2.776336] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >> driver >> > initialized >> > [ 2.785644] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >> driver >> > initialized >> > [ 2.795776] SmartReflex Class3 initialized >> > [ 2.863677] clock: disabling unused clocks to save power >> > [ 2.872497] platform iva.0: omap_voltage_scale: Already at the >> > requestedrate 360000000 >> > [ 2.880920] platform mpu.0: omap_voltage_scale: Already at the >> > requestedrate 500000000 >> > [ 2.889343] platform l3_main.0: omap_voltage_scale: Already at the >> > requestedrate 166000000 >> > [ 2.931488] omap_device: omap_i2c.1: new worst case deactivate >> latency 0: >> > 122070 >> > [ 2.940246] regulator_init_complete: incomplete constraints, leaving >> VDAC >> > on >> > [ 2.952911] twl_rtc twl_rtc: setting system clock to 2000-01-01 >> 00:00:00 >> > UTC (946684800) >> > [ 2.962005] omap_vout omap_vout: Buffer Size = 3686400 >> > [ 2.971313] omap_vout omap_vout: : registered and initialized video >> > device 15 >> > [ 2.978973] omap_vout omap_vout: Buffer Size = 3686400 >> > [ 2.987640] omap_vout omap_vout: : registered and initialized video >> > device 16 >> > [ 3.002319] Waiting for root device /dev/mmcblk0p2... >> > [ 3.166046] mmc0: new high speed SDHC card at address aaaa >> > [ 3.175537] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >> > [ 3.200164] mmcblk0: p1 p2 >> > [ 3.232910] EXT3-fs: barriers not enabled >> > [ 3.312805] kjournald starting. Commit interval 5 seconds >> > [ 3.319183] EXT3-fs (mmcblk0p2): warning: maximal mount count >> reached, >> > running e2fsck is recommended >> > [ 3.333465] EXT3-fs (mmcblk0p2): using internal journal >> > [ 3.339080] EXT3-fs (mmcblk0p2): recovery complete >> > [ 3.347442] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data >> > mode >> > [ 3.355468] VFS: Mounted root (ext3 filesystem) on device 179:2. >> > [ 3.362091] Freeing init memory: 200K >> > Failed to open /dev/kmsg for logging: No such file or directory >> > [ 3.685821] <30>systemd[1]: systemd 37 running in system mode. (+PAM >> > +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >> > >> > Welcome to The ֵngstrצm Distribution! >> > >> > [ 3.784942] <28>systemd[1]: /sbin/modprobe failed with error code 1. >> > [ 3.796173] <30>systemd[1]: Set hostname to <beagleboard>. >> > [ 4.271270] <27>systemd[1]: Failed to open /dev/autofs: No such file >> or >> > directory >> >> add: CONFIG_AUTOFS4_FS=y >> >> Regards, >> >> -- >> Robert Nelson >> http://www.rcn-ee.com/ >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to a topic in the >> Google Groups "BeagleBoard" group. >> To unsubscribe from this topic, visit >> https://groups.google.com/d/topic/beagleboard/RznTdyaz2gg/unsubscribe. >> To unsubscribe from this group and all its topics, send an email to >> [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
