Hi, When I compiled earlier kernel version which are supposed to support OMAP3530 with beaglebone I fail to start kernel (psp 3.0.1.6, kernel 2.6.32);
1920736 bytes read ## Booting kernel from Legacy Image at 80300000 ... Image Name: Linux-2.6.32 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1920672 Bytes = 1.8 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux........................................................................................................................ done, booting the kernel. <<-- NO more prinings -->> I just need to work with usb ethernet in 2.6.37... why does it fail with the kernel 2.6.37 ? Regards, Ran On Thu, Jan 15, 2015 at 7:14 PM, Ran Shalit <[email protected]> wrote: > Hi, > > Did anyone tried to work with the usb connector (the one that is marked as > "usb otg"), for ethernet with 2.6.37 ? > If not - maybe I should try use some older version for beagleboard ? > Regards, > Ran > > On Thu, Jan 15, 2015 at 6:36 PM, Ran Shalit <[email protected]> wrote: > >> Hi Robert, >> >> Thanks, >> I have compiled both modules and kernel, but still some error, without >> any information..... >> >> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >> g_ether.ko >> insmod: error inserting 'g_ether.ko': -1 No such device >> >> The new boot log is below. >> >> Is there any idea why it fails ? >> >> Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >> Beagle Rev C5 >> Reading boot sector >> Loading u-boot.bin from mmc >> >> >> U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >> >> , CPU-OPP2 L3-165MHz >> OMAP3 Beagle board + LPDDR/NAND >> DRAM: 256 MB >> NAND: 512 MiB >> In: serial >> Out: serial >> Err: serial >> Board revision Ax/Bx >> Die ID #74aa000700000000015a676401014023 >> Hit any key to stop autoboot: 0 >> mmc1 is available >> reading uImage >> >> 2927348 bytes read >> ## Booting kernel from Legacy Image at 80300000 ... >> Image Name: Linux-2.6.37 >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 2927284 Bytes = 2.8 MB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> OK >> >> Starting kernel ... >> >> Uncompressing Linux... done, booting the kernel. >> [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc version >> 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #8 Thu Jan 15 18:29:23 IST 2015 >> [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >> cr=10c53c7f >> [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >> instruction cache >> [ 0.000000] Machine: OMAP3 Beagle Board >> [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >> [ 0.000000] Memory policy: ECC disabled, Data cache writeback >> [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) >> [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 >> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >> Total pages: 64000 >> [ 0.000000] Kernel command line: console=ttyO2,115200n8 >> root=/dev/mmcblk0p2 rw rootwait >> [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >> [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 >> bytes) >> [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >> bytes) >> [ 0.000000] Memory: 252MB = 252MB total >> [ 0.000000] Memory: 242712k/242712k available, 19432k reserved, 0K >> highmem >> [ 0.000000] Virtual kernel memory layout: >> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >> [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >> [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >> [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >> [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >> [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >> [ 0.000000] .text : 0xc003a000 - 0xc056e0d0 (5329 kB) >> [ 0.000000] .data : 0xc0570000 - 0xc0725220 (1749 kB) >> [ 0.000000] NR_IRQS:409 >> [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >> [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >> [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >> [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >> [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >> [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >> interrupts >> [ 0.000000] Total of 96 interrupts on 1 active controller >> [ 0.000000] GPMC revision 5.0 >> [ 0.000000] Trying to install interrupt handler for IRQ402 >> [ 0.000000] Trying to install interrupt handler for IRQ403 >> [ 0.000000] Trying to install interrupt handler for IRQ404 >> [ 0.000000] Trying to install interrupt handler for IRQ405 >> [ 0.000000] Trying to install interrupt handler for IRQ406 >> [ 0.000000] Trying to install interrupt handler for IRQ407 >> [ 0.000000] Trying to install interrupt handler for IRQ408 >> [ 0.000000] Trying to install type control for IRQ409 >> [ 0.000000] Trying to set irq flags for IRQ409 >> [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >> [ 0.000000] Console: colour dummy device 80x30 >> [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >> Inc., Ingo Molnar >> [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >> [ 0.000000] ... MAX_LOCK_DEPTH: 48 >> [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >> [ 0.000000] ... CLASSHASH_SIZE: 4096 >> [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >> [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >> [ 0.000000] ... CHAINHASH_SIZE: 16384 >> [ 0.000000] memory used by lock dependency info: 3951 kB >> [ 0.000000] per task-struct memory footprint: 2304 bytes >> [ 0.000000] Calibrating delay loop... 458.96 BogoMIPS (lpj=1789952) >> [ 0.000000] pid_max: default: 32768 minimum: 301 >> [ 0.000000] Security Framework initialized >> [ 0.000000] Mount-cache hash table entries: 512 >> [ 0.000000] CPU: Testing write buffer coherency: ok >> [ 0.000000] devtmpfs: initialized >> [ 0.000000] regulator: core version 0.5 >> [ 0.000000] regulator: dummy: >> [ 0.000000] NET: Registered protocol family 16 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] OMAP GPIO hardware version 2.5 >> [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >> [ 0.000000] OMAP3 Beagle Rev: C4 >> [ 0.000000] Found NAND on CS0 >> [ 0.000000] Registering NAND on CS0 >> [ 0.000000] Unable to get DVI reset GPIO >> [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >> [ 0.000000] OMAP DMA hardware revision 4.0 >> [ 0.123657] bio: create slab <bio-0> at 0 >> [ 0.135101] SCSI subsystem initialized >> [ 0.149047] usbcore: registered new interface driver usbfs >> [ 0.151000] usbcore: registered new interface driver hub >> [ 0.152465] usbcore: registered new device driver usb >> [ 0.159149] omap_device: omap_i2c.1: new worst case activate latency >> 0: 61035 >> [ 0.159362] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >> [ 0.174316] twl4030: PIH (irq 7) chaining IRQs 368..375 >> [ 0.174560] twl4030: power (irq 373) chaining IRQs 376..383 >> [ 0.177703] twl4030: gpio (irq 368) chaining IRQs 384..401 >> [ 0.194580] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >> standby >> [ 0.198181] regulator: VDAC: 1800 mV normal standby >> [ 0.201873] regulator: VDVI: 1800 mV normal standby >> [ 0.205810] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >> standby >> [ 0.210021] regulator: VAUX3: 1800 mV normal standby >> [ 0.213623] regulator: VAUX4: 1800 mV normal standby >> [ 0.214294] omap_device: omap_i2c.1: new worst case deactivate latency >> 0: 91552 >> [ 0.214691] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >> [ 0.229003] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >> [ 0.239440] Advanced Linux Sound Architecture Driver Version 1.0.23. >> [ 0.244750] Switching to clocksource 32k_counter >> [ 0.435150] musb-hdrc: version 6.0, peripheral, debug=0 >> [ 0.435577] musb-hdrc musb-hdrc.0: degrade from otg to peripheral-only >> mode >> [ 0.435668] musb-hdrc musb-hdrc.0: dma type: dma-inventra >> [ 0.435699] HS USB OTG: no transceiver configured >> [ 0.435729] musb-hdrc musb-hdrc.0: musb_init_controller failed with >> status -19 >> [ 0.437591] NET: Registered protocol family 2 >> [ 0.438537] IP route cache hash table entries: 2048 (order: 1, 8192 >> bytes) >> [ 0.441192] TCP established hash table entries: 8192 (order: 4, 65536 >> bytes) >> [ 0.441772] TCP bind hash table entries: 8192 (order: 6, 360448 bytes) >> [ 0.447326] TCP: Hash tables configured (established 8192 bind 8192) >> [ 0.447509] TCP reno registered >> [ 0.447540] UDP hash table entries: 128 (order: 1, 12288 bytes) >> [ 0.448059] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) >> [ 0.449432] NET: Registered protocol family 1 >> [ 0.451385] RPC: Registered udp transport module. >> [ 0.451416] RPC: Registered tcp transport module. >> [ 0.451416] RPC: Registered tcp NFSv4.1 backchannel transport module. >> [ 0.452758] NetWinder Floating Point Emulator V0.97 (double precision) >> [ 0.456146] platform iva.0: Enabled OPP corresponding to 720MHz >> [ 0.460144] omap-iommu omap-iommu.0: isp registered >> [ 0.461303] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >> [ 0.649597] VFS: Disk quotas dquot_6.5.2 >> [ 0.649780] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> [ 0.653320] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, >> Inc. >> [ 0.657958] msgmni has been set to 474 >> [ 0.663879] io scheduler noop registered >> [ 0.663909] io scheduler deadline registered >> [ 0.664184] io scheduler cfq registered (default) >> [ 0.729553] OMAP DSS rev 2.0 >> [ 0.730224] OMAP DISPC rev 3.0 >> [ 0.730407] OMAP VENC rev 2 >> [ 0.731964] OMAP DSI rev 1.0 >> [ 1.061706] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >> [ 1.074340] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP >> UART0 >> [ 1.077087] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP >> UART1 >> [ 1.079193] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP >> UART2 >> [ 1.822540] console [ttyO2] enabled >> [ 1.891143] brd: module loaded >> [ 1.925689] loop: module loaded >> [ 1.937622] mtdoops: mtd device (mtddev=name/number) must be supplied >> [ 1.944610] omap2-nand driver initializing >> [ 1.949676] ONFI flash detected >> [ 1.953247] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron ) >> [ 1.960388] Creating 5 MTD partitions on "omap2-nand.0": >> [ 1.966064] 0x000000000000-0x000000080000 : "X-Loader" >> [ 1.984436] 0x000000080000-0x000000260000 : "U-Boot" >> [ 1.999542] 0x000000260000-0x000000280000 : "U-Boot Env" >> [ 2.014068] 0x000000280000-0x000000680000 : "Kernel" >> [ 2.030242] 0x000000680000-0x000020000000 : "File System" >> [ 2.301544] OneNAND driver initializing >> [ 2.317413] mice: PS/2 mouse device common for all mice >> [ 2.327362] input: gpio-keys as >> /devices/platform/gpio-keys/input/input0 >> [ 2.345733] omap_device: omap_i2c.1: new worst case activate latency >> 0: 122070 >> [ 2.355102] input: twl4030_pwrbutton as >> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >> [ 2.374267] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >> [ 2.381378] twl_rtc twl_rtc: Power up reset detected. >> [ 2.387847] twl_rtc twl_rtc: Enabling TWL-RTC. >> [ 2.395385] i2c /dev entries driver >> [ 2.407806] Linux media interface: v0.10 >> [ 2.413055] Linux video capture interface: v2.00 >> [ 2.420562] omap3isp supply VDD_CSIPHY1 not found, using dummy >> regulator >> [ 2.427795] omap3isp supply VDD_CSIPHY2 not found, using dummy >> regulator >> [ 2.435546] omap3isp omap3isp: Revision 2.0 found >> [ 2.440887] omap-iommu omap-iommu.0: isp: version 1.1 >> [ 2.552551] omap_i2c omap_i2c.2: Arbitration lost >> [ 2.573242] mt9v113 2-003c: chip id mismatch read 0x0, expecting 0x2280 >> [ 2.590240] isp_register_subdev_group: Unable to register subdev >> mt9v113 >> [ 2.598937] omap_device: omap_wdt.-1: new worst case activate latency >> 0: 30517 >> [ 2.609344] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> [ 2.615814] omap_device: omap_wdt.-1: new worst case deactivate >> latency 0: 30517 >> [ 2.625457] twl4030_wdt twl4030_wdt: Failed to register misc device >> [ 2.632202] twl4030_wdt: probe of twl4030_wdt failed with error -16 >> [ 2.661651] usbcore: registered new interface driver usbhid >> [ 2.667602] usbhid: USB HID core driver >> [ 2.679443] ALSA device list: >> [ 2.682678] No soundcards found. >> [ 2.686248] oprofile: hardware counters not available >> [ 2.691619] oprofile: using timer interrupt. >> [ 2.696716] TCP cubic registered >> [ 2.700225] Initializing XFRM netlink socket >> [ 2.704986] NET: Registered protocol family 17 >> [ 2.709930] NET: Registered protocol family 15 >> [ 2.715393] Registering the dns_resolver key type >> [ 2.721282] VFP support v0.3: implementor 41 architecture 3 part 30 >> variant c rev 1 >> [ 2.731414] ThumbEE CPU extension supported. >> [ 2.758483] Power Management for TI OMAP3. >> [ 2.763824] sr_init: No PMIC hook to init smartreflex >> [ 2.769836] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >> driver initialized >> [ 2.779174] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >> driver initialized >> [ 2.789276] SmartReflex Class3 initialized >> [ 2.857177] clock: disabling unused clocks to save power >> [ 2.866088] platform iva.0: omap_voltage_scale: Already at the >> requestedrate 360000000 >> [ 2.874511] platform mpu.0: omap_voltage_scale: Already at the >> requestedrate 500000000 >> [ 2.882934] platform l3_main.0: omap_voltage_scale: Already at the >> requestedrate 166000000 >> [ 2.927032] regulator_init_complete: incomplete constraints, leaving >> VDAC on >> [ 2.938446] twl_rtc twl_rtc: setting system clock to 2000-01-01 >> 00:00:00 UTC (946684800) >> [ 2.947753] omap_vout omap_vout: Buffer Size = 3686400 >> [ 2.957153] omap_vout omap_vout: : registered and initialized video >> device 15 >> [ 2.964782] omap_vout omap_vout: Buffer Size = 3686400 >> [ 2.973541] omap_vout omap_vout: : registered and initialized video >> device 16 >> [ 2.988342] Waiting for root device /dev/mmcblk0p2... >> [ 3.141418] mmc0: new high speed SDHC card at address aaaa >> [ 3.151336] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >> [ 3.175750] mmcblk0: p1 p2 >> [ 3.218505] EXT3-fs: barriers not enabled >> [ 3.227325] kjournald starting. Commit interval 5 seconds >> [ 3.233612] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, >> running e2fsck is recommended >> [ 3.247222] EXT3-fs (mmcblk0p2): using internal journal >> [ 3.252807] EXT3-fs (mmcblk0p2): recovery complete >> [ 3.258544] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data >> mode >> [ 3.266540] VFS: Mounted root (ext3 filesystem) on device 179:2. >> [ 3.273132] Freeing init memory: 200K >> Failed to open /dev/kmsg for logging: No such file or directory >> [ 3.609405] <30>systemd[1]: systemd 37 running in system mode. (+PAM >> +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >> >> Welcome to The ֵngstrצm Distribution! >> >> [ 3.713439] <28>systemd[1]: /sbin/modprobe failed with error code 1. >> [ 3.724670] <30>systemd[1]: Set hostname to <beagleboard>. >> Starting Runtime Directory... >> Starting Remount API VFS... >> Starting Lock Directory... >> Starting Media Directory... >> Started Apply Kernel Variables [ >> OK ] >> Started Huge Pages File System [ >> OK ] >> Starting POSIX Message Queue File System... >> Starting File System Check on Root Device... >> Started Load Kernel Modules [ >> OK ] >> Started Configuration File System [ >> OK ] >> Started FUSE Control File System [ >> OK ] >> Started Set Up Additional Binary Formats [ >> OK ] >> [ 4.677764] <30>systemd-fsck[593]: Root directory is writable, >> skipping check. >> Starting Debug File System... >> Started Security File System [ >> OK ] >> Starting Syslog Kernel Log Buffer Bridge... >> Started Syslog Kernel Log Buffer Bridge [ >> OK ] >> Starting udev Coldplug all Devices... >> Starting udev Kernel Device Manager... >> Started Runtime Directory [ >> OK ] >> Started Remount API VFS [ >> OK ] >> Started Lock Directory [ >> OK ] >> Started udev Ker[ 5.031005] <30>udevd[600]: starting version 175 >> nel Device Manager [ OK ] >> Started Media Directory [ >> OK ] >> Started POSIX Message Queue File System [ >> OK ] >> Started File System Check on Root Device [ >> OK ] >> Started Debug File System [ >> OK ] >> Starting Remount Root FS... >> Starting STDOUT Syslog Bridge... >> Started STDOUT Syslog Bridge [ >> OK ] >> Started Remount Root FS [ >> OK ] >> Started Opkg first boot configure [ >> OK ] >> Starting /tmp... >> Started Machine ID first boot configure [ >> OK ] >> Started /tmp [ >> OK ] >> Starting Load Random Seed... >> Starting Recreate Volatile Files and Directories... >> Started Load Random Seed [ >> OK ] >> Started Recreate Volatile Files and Directories [ >> OK ] >> Starting Console System Startup Logging... >> Starting xinetd.service... >> Started Angstrom LED config [ >> OK ] >> Starting Timestamping service... >> Started Timestamping service [ >> OK ] >> Starting Network Manager... >> Started SSH Key Generation [ >> OK ] >> Starting System Logging Service... >> Starting Permit User Sessions... >> Starting Login Service... >> Starting Avahi mDNS/DNS-SD Stack... >> Starting Periodic Command Scheduler... >> Started Periodic Command Scheduler [ >> OK ] >> Starting internet superserver: xinetdStarting D-Bus System Message Bus... >> Starting Disk Manager... >> Started Console System Startup Logging [ >> OK ] >> [ 8.354309] <27>systemd-logind[707]: Failed to open >> /sys/class/tty/tty0/active: No such file or directory >> Started Permit User Sessions [ >> OK ] >> [ 8.659515] <27>systemd-logind[707]: Failed to fully start up daemon: >> No such file or directory >> [ 8.877380] <29>systemd[1]: systemd-logind.service: main process >> exited, code=exited, status=1 >> [ 9.057952] <75>/usr/sbin/crond[722]: (CRON) INFO (Syslog will be used >> instead of sendmail.): No such file or directory >> . >> Failed to start Login Service >> [FAILED] >> [ 9.415985] <30>avahi-daemon[711]: Found user 'avahi' (UID 998) and >> group 'avahi' (GID 996). >> [ 9.478942] <30>avahi-daemon[711]: Successfully dropped root >> privileges. >> See 'systemctl status systemd-logind.service' for details. >> [ 9.517791] <29>systemd[1]: Unit systemd-logind.service entered failed >> state. >> [ 9.659942] <30>avahi-daemon[711]: avahi-daemon 0.6.30 starting up. >> Started xinetd.service [ >> OK ] >> [ 9.930999] <26>xinetd[868]: 868 {init_services} no services. >> Exiting... >> Starting Serial Getty on ttyO2... >> [ 10.786376] <30>NetworkManager[704]: NetworkManager[704]: <info> >> NetworkManager (version 0.9.2.0) is starting... >> Started Serial Getty on ttyO2 [ >> OK ] >> [ 11.033538] <30>udisks-daemon[770]: (process:770): GLib-WARNING **: >> goption.c:2168: ignoring no-arg, optional-arg or filename flags (16) on >> option of type 1 >> [ 11.310058] <14>NetworkManager[704]: <info> NetworkManager (version >> 0.9.2.0) is starting... >> Started D-Bus System Message Bus [ >> OK ] >> [ 11.474243] <30>NetworkManager[704]: NetworkManager[704]: <info> Read >> config file (null) >> [ 11.721771] <14>NetworkManager[704]: <info> Read config file (null) >> [ 11.728485] <30>load-timestamp.sh[702]: Update systemtime from >> /etc/timestamp >> [ 12.190551] <30>load-timestamp.sh[702]: Thu Jan 12 12:19:00 UTC 2012 >> [ 12.656372] <27>systemd-uaccess[1031]: Failed to apply ACL on >> /dev/v4l-subdev3: Operation not supported >> [ 12.891265] <27>systemd-uaccess[1027]: Failed to apply ACL on >> /dev/v4l-subdev0: Operation not supported >> >> .---O---. [ 13.117218] >> <27>systemd-uaccess[1019]: Failed to apply ACL on /dev/v4l-subdev1: >> Operation not supported >> >> | | .-. o o >> | | |-----.-----.-[ 13.337951] <27>systemd-uaccess[1033]: Failed to >> apply ACL on /dev/v4l-subdev2: Operation not supported >> ----.| | .----..--[ 13.378295] <27>systemd-uaccess[1037]: Failed to >> apply ACL on /dev/v4l-subdev6: Operation not supported >> ---.-----. >> | | | __ | ---'| '--.| .-'| | | >> | | | | | |--- [ 13.526580] <27>systemd-uaccess[1040]: Failed >> to apply ACL on /dev/v4l-subdev7: Operation not supported >> || --'| | | ' | | | | >> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >> [ 13.677337] <27>systemd-uaccess[1028]: Failed to apply ACL on >> /dev/v4l-subdev5: Operation not supported >> -' | >> '---' >> >> The Angstrom Distribution beagleboard ttyO2 >> >> Angstrom v2012.01-co[ 13.979644] <27>systemd-uaccess[1042]: Failed to >> apply ACL on /dev/v4l-subdev4: Operation not supported >> re - Kernel 2.6.37 >> >> beagleboard login: [ 14.332580] <27>systemd-uaccess[1049]: Failed to >> apply ACL on /dev/video0: Operation not supported >> [ 14.667114] <27>systemd-uaccess[1051]: Failed to apply ACL on >> /dev/video1: Operation not supported >> [ 14.995208] <27>systemd-uaccess[1053]: Failed to apply ACL on >> /dev/video3: Operation not supported >> Started udev Coldplug all Devices [ >> OK ] >> >> [ 15.218170] <27>systemd-uaccess[1055]: Failed to apply ACL on >> /dev/video2: Operation not supported >> [ 15.450988] <27>systemd-uaccess[1057]: Failed to apply ACL on >> /dev/video4: Operation not supported >> Started Disk Manager [ >> OK ] >> >> Started Avahi mDNS/DNS-SD Stack >> [[ 15.689880] <27> OK ] >> systemd-uaccess[1063]: Failed to apply ACL on >> /dev/video5: Operation not supported >> [ 15.800720] <27>systemd-uaccess[1073]: Failed to apply ACL on >> /dev/video8: Operation not supported >> [ 16.030517] <27>systemd-uaccess[1072]: Failed to apply ACL on >> /dev/video7: Operation not supported >> [ 16.091583] <27>systemd-uaccess[1086]: Failed to apply ACL on >> /dev/video6: Operation not supported >> Stopping Syslog Kernel Log Buffer Bridge... >> [ 16.201354] >> <30>udisks-daemon[770]: (udisks-daemon:770): udisks-daemon-DEBUG: Starting >> daemon version 1.0.4 >> [ 16.326660] <30>avahi-daemon[711]: Successfully called chroot(). >> [ 16.400512] <30>avahi-daemon[711]: Successfully dropped remaining >> capabilities. >> [ 16.473449] <30>avahi-daemon[711]: Loading service file >> /services/sftp-ssh.service. >> [ 16.510803] <30>avahi-daemon[711]: Loading service file >> /services/ssh.service. >> [ 16.565338] <30>avahi-daemon[711]: Loading service file >> /services/udisks.service. >> [ 16.644561] <30>avahi-daemon[711]: Network interface enumeration >> completed. >> [ 16.669464] <30>avahi-daemon[711]: Registering HINFO record with >> values 'ARMV7L'/'LINUX'. >> [ 16.757904] <30>avahi-daemon[711]: Server startup complete. Host name >> is beagleboard.local. Local service cookie is 441939348. >> Starting Getty on tty1... >> [ 16.862426] <30>avahi-daemon[711]: Service >> "beagleboard" (/services/udisks.service) successfully established. >> [ 16.971832] <30>dbus-daemon[969]: dbus[969]: [system] Activating >> service name='org.freedesktop.PolicyKit1' (using servicehelper) >> Started Getty on tty1 [ >> OK ] >> >> [ 17.104522] <29>dbus[969]: [system] Activating service >> name='org.freedesktop.PolicyKit1' (using servicehelper) >> [ 17.218292] <30>avahi-daemon[711]: Service "beagleboard" >> (/services/ssh.service) successfully established. >> Starting Gnome D[ 17.271667] <27>isplay Manager..systemd-uaccess. >> >> [1199]: Failed to apply ACL on /dev/snd/timer: Operation not supported >> [ 17.293273] <30>avahi-daemon[711]: Service "beagleboard" >> (/services/sftp-ssh.service) successfully established. >> Started Gnome Display Manager [ >> OK ] >> >> Stopped Syslog Kernel Log Buffer Bridge >> [ OK ] >> >> Started System Logging Service >> [ OK ] >> >> Started Network Manager >> [ OK ] >> >> .---O---. >> | | .-. o o >> | | |-----.-----.-----.| | .----..-----.-----. >> | | | __ | ---'| '--.| .-'| | | >> | | | | | |--- || --'| | | ' | | | | >> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >> -' | >> '---' >> >> The Angstrom Distribution beagleboard ttyO2 >> >> Angstrom v2012.01-core - Kernel 2.6.37 >> >> beagleboard login: >> .---O---. >> | | .-. o o >> | | |-----.-----.-----.| | .----..-----.-----. >> | | | __ | ---'| '--.| .-'| | | >> | | | | | |--- || --'| | | ' | | | | >> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >> -' | >> '---' >> >> The Angstrom Distribution beagleboard ttyO2 >> >> Angstrom v2012.01-core - Kernel 2.6.37 >> >> beagleboard login: root >> Last login: Thu Jan 12 12:19:48 GMT 2012 on ttyO2 >> root@beagleboard:~# >> root@beagleboard:~# >> root@beagleboard:~# cd /lib/modules/2.6.37/kernel/drivers/usb/gadget/ >> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >> g_ether.ko >> insmod: error inserting 'g_ether.ko': -1 No such device >> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget >> >> Regards, >> Ran >> >> >> On Thu, Jan 15, 2015 at 6:26 PM, Robert Nelson <[email protected]> >> wrote: >> >>> On Thu, Jan 15, 2015 at 10:23 AM, Ran Shalit <[email protected]> >>> wrote: >>> > Hi Robert, >>> > >>> > Thank you very much. >>> > I was lazy not to notice that.... >>> > It now seems better (less errors on boot), but still fails with same >>> error: >>> > insmod: error inserting 'g_ether.ko': -1 No such device >>> > Can you give me another hint what might cause such failure? >>> > >>> > This is the boot log: >>> > >>> > Last login: Thu Jan 12 12:31:58 GMT 2012 on ttyO2 >>> > root@beagleboard:~# >>> > root@beagleboard:~# >>> > root@beagleboard:~# >>> > root@beagleboard:~# modprobe g_ether >>> > [ 30.667053] g_ether: disagrees about version of symbol module_layout >>> > FATAL: Error inserting g_ether >>> >>> This means your kernel was built seperatly from the modules.. >>> >>> When you build your kernel, just also build 'make modules' and install >>> them to the rootfs.. >>> >>> >>> > (/lib/modules/2.6.37/kernel/drivers/usb/gadget/g_ether.ko): Invalid >>> module >>> > format >>> > root@beagleboard:~# d >>> > >>> > Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >>> > Beagle Rev C5 >>> > Reading boot sector >>> > Loading u-boot.bin from mmc >>> > >>> > >>> > U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >>> > >>> > , CPU-OPP2 L3-165MHz >>> > OMAP3 Beagle board + LPDDR/NAND >>> > DRAM: 256 MB >>> > NAND: 512 MiB >>> > In: serial >>> > Out: serial >>> > Err: serial >>> > Board revision Ax/Bx >>> > Die ID #74aa000700000000015a676401014023 >>> > Hit any key to stop autoboot: 0 >>> > mmc1 is available >>> > reading uImage >>> > >>> > 2918324 bytes read >>> > ## Booting kernel from Legacy Image at 80300000 ... >>> > Image Name: Linux-2.6.37 >>> > Image Type: ARM Linux Kernel Image (uncompressed) >>> > Data Size: 2918260 Bytes = 2.8 MB >>> > Load Address: 80008000 >>> > Entry Point: 80008000 >>> > Verifying Checksum ... OK >>> > Loading Kernel Image ... OK >>> > OK >>> > >>> > Starting kernel ... >>> > >>> > Uncompressing Linux... done, booting the kernel. >>> > [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc >>> version >>> > 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #7 Thu Jan 15 18:09:40 IST 2015 >>> > [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >>> > cr=10c53c7f >>> > [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >>> > instruction cache >>> > [ 0.000000] Machine: OMAP3 Beagle Board >>> > [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >>> > [ 0.000000] Memory policy: ECC disabled, Data cache writeback >>> > [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) >>> > [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: >>> 0x10000 >>> > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >>> Total >>> > pages: 64000 >>> > [ 0.000000] Kernel command line: console=ttyO2,115200n8 >>> > root=/dev/mmcblk0p2 rw rootwait >>> > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >>> > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 >>> > bytes) >>> > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >>> bytes) >>> > [ 0.000000] Memory: 252MB = 252MB total >>> > [ 0.000000] Memory: 242740k/242740k available, 19404k reserved, 0K >>> > highmem >>> > [ 0.000000] Virtual kernel memory layout: >>> > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >>> > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >>> > [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >>> > [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >>> > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >>> > [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >>> > [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >>> > [ 0.000000] .text : 0xc003a000 - 0xc0568f4c (5308 kB) >>> > [ 0.000000] .data : 0xc056a000 - 0xc071f1a0 (1749 kB) >>> > [ 0.000000] NR_IRQS:409 >>> > [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>> > [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >>> > [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >>> > [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >>> > [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >>> > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >>> > interrupts >>> > [ 0.000000] Total of 96 interrupts on 1 active controller >>> > [ 0.000000] GPMC revision 5.0 >>> > [ 0.000000] Trying to install interrupt handler for IRQ402 >>> > [ 0.000000] Trying to install interrupt handler for IRQ403 >>> > [ 0.000000] Trying to install interrupt handler for IRQ404 >>> > [ 0.000000] Trying to install interrupt handler for IRQ405 >>> > [ 0.000000] Trying to install interrupt handler for IRQ406 >>> > [ 0.000000] Trying to install interrupt handler for IRQ407 >>> > [ 0.000000] Trying to install interrupt handler for IRQ408 >>> > [ 0.000000] Trying to install type control for IRQ409 >>> > [ 0.000000] Trying to set irq flags for IRQ409 >>> > [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >>> > [ 0.000000] Console: colour dummy device 80x30 >>> > [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >>> Inc., >>> > Ingo Molnar >>> > [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >>> > [ 0.000000] ... MAX_LOCK_DEPTH: 48 >>> > [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >>> > [ 0.000000] ... CLASSHASH_SIZE: 4096 >>> > [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >>> > [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >>> > [ 0.000000] ... CHAINHASH_SIZE: 16384 >>> > [ 0.000000] memory used by lock dependency info: 3951 kB >>> > [ 0.000000] per task-struct memory footprint: 2304 bytes >>> > [ 0.000000] Calibrating delay loop... 456.86 BogoMIPS (lpj=1781760) >>> > [ 0.000000] pid_max: default: 32768 minimum: 301 >>> > [ 0.000000] Security Framework initialized >>> > [ 0.000000] Mount-cache hash table entries: 512 >>> > [ 0.000000] CPU: Testing write buffer coherency: ok >>> > [ 0.000000] devtmpfs: initialized >>> > [ 0.000000] regulator: core version 0.5 >>> > [ 0.000000] regulator: dummy: >>> > [ 0.000000] NET: Registered protocol family 16 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>> > [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >>> > [ 0.000000] OMAP3 Beagle Rev: C4 >>> > [ 0.000000] Found NAND on CS0 >>> > [ 0.000000] Registering NAND on CS0 >>> > [ 0.000000] Unable to get DVI reset GPIO >>> > [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >>> > [ 0.000000] OMAP DMA hardware revision 4.0 >>> > [ 0.122314] bio: create slab <bio-0> at 0 >>> > [ 0.133697] SCSI subsystem initialized >>> > [ 0.147491] usbcore: registered new interface driver usbfs >>> > [ 0.149322] usbcore: registered new interface driver hub >>> > [ 0.150878] usbcore: registered new device driver usb >>> > [ 0.157501] omap_device: omap_i2c.1: new worst case activate >>> latency 0: >>> > 30517 >>> > [ 0.157684] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >>> > [ 0.172485] twl4030: PIH (irq 7) chaining IRQs 368..375 >>> > [ 0.172729] twl4030: power (irq 373) chaining IRQs 376..383 >>> > [ 0.175842] twl4030: gpio (irq 368) chaining IRQs 384..401 >>> > [ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >>> standby >>> > [ 0.196044] regulator: VDAC: 1800 mV normal standby >>> > [ 0.199615] regulator: VDVI: 1800 mV normal standby >>> > [ 0.203613] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >>> standby >>> > [ 0.207763] regulator: VAUX3: 1800 mV normal standby >>> > [ 0.211334] regulator: VAUX4: 1800 mV normal standby >>> > [ 0.211914] omap_device: omap_i2c.1: new worst case deactivate >>> latency 0: >>> > 61035 >>> > [ 0.221954] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >>> > [ 0.236083] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >>> > [ 0.246398] Advanced Linux Sound Architecture Driver Version 1.0.23. >>> > [ 0.251586] Switching to clocksource 32k_counter >>> > [ 0.440246] musb-hdrc: version 6.0, peripheral, debug=0 >>> > [ 0.440673] musb-hdrc musb-hdrc.0: degrade from otg to >>> peripheral-only >>> > mode >>> > [ 0.440795] musb-hdrc musb-hdrc.0: dma type: dma-inventra >>> > [ 0.440826] HS USB OTG: no transceiver configured >>> > [ 0.440856] musb-hdrc musb-hdrc.0: musb_init_controller failed with >>> > status -19 >>> > [ 0.442718] NET: Registered protocol family 2 >>> > [ 0.443664] IP route cache hash table entries: 2048 (order: 1, 8192 >>> > bytes) >>> > [ 0.446136] TCP established hash table entries: 8192 (order: 4, >>> 65536 >>> > bytes) >>> > [ 0.446746] TCP bind hash table entries: 8192 (order: 6, 360448 >>> bytes) >>> > [ 0.452423] TCP: Hash tables configured (established 8192 bind 8192) >>> > [ 0.452545] TCP reno registered >>> > [ 0.452606] UDP hash table entries: 128 (order: 1, 12288 bytes) >>> > [ 0.453033] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) >>> > [ 0.454437] NET: Registered protocol family 1 >>> > [ 0.456481] RPC: Registered udp transport module. >>> > [ 0.456512] RPC: Registered tcp transport module. >>> > [ 0.456542] RPC: Registered tcp NFSv4.1 backchannel transport >>> module. >>> > [ 0.457855] NetWinder Floating Point Emulator V0.97 (double >>> precision) >>> > [ 0.461059] platform iva.0: Enabled OPP corresponding to 720MHz >>> > [ 0.465179] omap-iommu omap-iommu.0: isp registered >>> > [ 0.466308] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >>> > [ 0.654205] VFS: Disk quotas dquot_6.5.2 >>> > [ 0.654388] Dquot-cache hash table entries: 1024 (order 0, 4096 >>> bytes) >>> > [ 0.657714] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red >>> Hat, >>> > Inc. >>> > [ 0.659271] msgmni has been set to 474 >>> > [ 0.665100] io scheduler noop registered >>> > [ 0.665191] io scheduler deadline registered >>> > [ 0.665435] io scheduler cfq registered (default) >>> > [ 0.728576] OMAP DSS rev 2.0 >>> > [ 0.729248] OMAP DISPC rev 3.0 >>> > [ 0.729431] OMAP VENC rev 2 >>> > [ 0.730957] OMAP DSI rev 1.0 >>> > [ 1.060791] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >>> > [ 1.073242] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >>> OMAP >>> > UART0 >>> > [ 1.076141] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >>> OMAP >>> > UART1 >>> > [ 1.078155] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >>> OMAP >>> > UART2 >>> > [ 1.821472] console [ttyO2] enabled >>> > [ 1.889343] brd: module loaded >>> > [ 1.923370] loop: module loaded >>> > [ 1.935363] mtdoops: mtd device (mtddev=name/number) must be >>> supplied >>> > [ 1.942352] omap2-nand driver initializing >>> > [ 1.947479] ONFI flash detected >>> > [ 1.951019] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc >>> (Micron ) >>> > [ 1.958160] Creating 5 MTD partitions on "omap2-nand.0": >>> > [ 1.963836] 0x000000000000-0x000000080000 : "X-Loader" >>> > [ 1.982055] 0x000000080000-0x000000260000 : "U-Boot" >>> > [ 1.997100] 0x000000260000-0x000000280000 : "U-Boot Env" >>> > [ 2.011535] 0x000000280000-0x000000680000 : "Kernel" >>> > [ 2.027618] 0x000000680000-0x000020000000 : "File System" >>> > [ 2.298248] OneNAND driver initializing >>> > [ 2.315246] mice: PS/2 mouse device common for all mice >>> > [ 2.324920] input: gpio-keys as >>> /devices/platform/gpio-keys/input/input0 >>> > [ 2.343780] omap_device: omap_i2c.1: new worst case activate >>> latency 0: >>> > 91552 >>> > [ 2.352966] input: twl4030_pwrbutton as >>> > >>> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >>> > [ 2.372009] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>> > [ 2.379119] twl_rtc twl_rtc: Power up reset detected. >>> > [ 2.385589] twl_rtc twl_rtc: Enabling TWL-RTC. >>> > [ 2.393066] i2c /dev entries driver >>> > [ 2.405456] Linux media interface: v0.10 >>> > [ 2.410736] Linux video capture interface: v2.00 >>> > [ 2.418273] omap3isp supply VDD_CSIPHY1 not found, using dummy >>> regulator >>> > [ 2.425506] omap3isp supply VDD_CSIPHY2 not found, using dummy >>> regulator >>> > [ 2.433227] omap3isp omap3isp: Revision 2.0 found >>> > [ 2.438476] omap-iommu omap-iommu.0: isp: version 1.1 >>> > [ 2.559204] omap_i2c omap_i2c.2: Arbitration lost >>> > [ 2.580078] mt9v113 2-003c: chip id mismatch read 0x0, expecting >>> 0x2280 >>> > [ 2.597198] isp_register_subdev_group: Unable to register subdev >>> mt9v113 >>> > [ 2.605865] omap_device: omap_wdt.-1: new worst case activate >>> latency 0: >>> > 30517 >>> > [ 2.616241] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>> > [ 2.622711] omap_device: omap_wdt.-1: new worst case deactivate >>> latency >>> > 0: 30517 >>> > [ 2.632354] twl4030_wdt twl4030_wdt: Failed to register misc device >>> > [ 2.639099] twl4030_wdt: probe of twl4030_wdt failed with error -16 >>> > [ 2.668334] usbcore: registered new interface driver usbhid >>> > [ 2.674285] usbhid: USB HID core driver >>> > [ 2.686126] ALSA device list: >>> > [ 2.689392] No soundcards found. >>> > [ 2.692962] oprofile: hardware counters not available >>> > [ 2.698333] oprofile: using timer interrupt. >>> > [ 2.703430] TCP cubic registered >>> > [ 2.706939] Initializing XFRM netlink socket >>> > [ 2.711639] NET: Registered protocol family 17 >>> > [ 2.716613] NET: Registered protocol family 15 >>> > [ 2.722045] Registering the dns_resolver key type >>> > [ 2.727783] VFP support v0.3: implementor 41 architecture 3 part 30 >>> > variant c rev 1 >>> > [ 2.737945] ThumbEE CPU extension supported. >>> > [ 2.764984] Power Management for TI OMAP3. >>> > [ 2.770355] sr_init: No PMIC hook to init smartreflex >>> > [ 2.776336] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >>> driver >>> > initialized >>> > [ 2.785644] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >>> driver >>> > initialized >>> > [ 2.795776] SmartReflex Class3 initialized >>> > [ 2.863677] clock: disabling unused clocks to save power >>> > [ 2.872497] platform iva.0: omap_voltage_scale: Already at the >>> > requestedrate 360000000 >>> > [ 2.880920] platform mpu.0: omap_voltage_scale: Already at the >>> > requestedrate 500000000 >>> > [ 2.889343] platform l3_main.0: omap_voltage_scale: Already at the >>> > requestedrate 166000000 >>> > [ 2.931488] omap_device: omap_i2c.1: new worst case deactivate >>> latency 0: >>> > 122070 >>> > [ 2.940246] regulator_init_complete: incomplete constraints, >>> leaving VDAC >>> > on >>> > [ 2.952911] twl_rtc twl_rtc: setting system clock to 2000-01-01 >>> 00:00:00 >>> > UTC (946684800) >>> > [ 2.962005] omap_vout omap_vout: Buffer Size = 3686400 >>> > [ 2.971313] omap_vout omap_vout: : registered and initialized video >>> > device 15 >>> > [ 2.978973] omap_vout omap_vout: Buffer Size = 3686400 >>> > [ 2.987640] omap_vout omap_vout: : registered and initialized video >>> > device 16 >>> > [ 3.002319] Waiting for root device /dev/mmcblk0p2... >>> > [ 3.166046] mmc0: new high speed SDHC card at address aaaa >>> > [ 3.175537] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >>> > [ 3.200164] mmcblk0: p1 p2 >>> > [ 3.232910] EXT3-fs: barriers not enabled >>> > [ 3.312805] kjournald starting. Commit interval 5 seconds >>> > [ 3.319183] EXT3-fs (mmcblk0p2): warning: maximal mount count >>> reached, >>> > running e2fsck is recommended >>> > [ 3.333465] EXT3-fs (mmcblk0p2): using internal journal >>> > [ 3.339080] EXT3-fs (mmcblk0p2): recovery complete >>> > [ 3.347442] EXT3-fs (mmcblk0p2): mounted filesystem with ordered >>> data >>> > mode >>> > [ 3.355468] VFS: Mounted root (ext3 filesystem) on device 179:2. >>> > [ 3.362091] Freeing init memory: 200K >>> > Failed to open /dev/kmsg for logging: No such file or directory >>> > [ 3.685821] <30>systemd[1]: systemd 37 running in system mode. (+PAM >>> > +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >>> > >>> > Welcome to The ֵngstrצm Distribution! >>> > >>> > [ 3.784942] <28>systemd[1]: /sbin/modprobe failed with error code 1. >>> > [ 3.796173] <30>systemd[1]: Set hostname to <beagleboard>. >>> > [ 4.271270] <27>systemd[1]: Failed to open /dev/autofs: No such >>> file or >>> > directory >>> >>> add: CONFIG_AUTOFS4_FS=y >>> >>> Regards, >>> >>> -- >>> Robert Nelson >>> http://www.rcn-ee.com/ >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "BeagleBoard" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/beagleboard/RznTdyaz2gg/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
