Hi, I solved the issue. I compile now inside kernel and added: CONFIG_USB_MUSB_OMAP2PLUS_GLUE
Thank you very much for all help! Ran On Fri, Jan 16, 2015 at 8:23 AM, Ran Shalit <[email protected]> wrote: > Hello, > > Can anyone please try to see if he can work with usb otg and beagleboard > this is the download page for kernel 2.6.37 I use: > > http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/OMAP_04_02/04_02_00_07/index_FDS.html > > Regards, > Ran > > On Thu, Jan 15, 2015 at 8:16 PM, Ran Shalit <[email protected]> wrote: > >> Hi, >> >> When I compiled earlier kernel version which are supposed to support >> OMAP3530 with beaglebone I fail to start kernel (psp 3.0.1.6, kernel >> 2.6.32); >> >> 1920736 bytes read >> ## Booting kernel from Legacy Image at 80300000 ... >> Image Name: Linux-2.6.32 >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 1920672 Bytes = 1.8 MB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> OK >> >> Starting kernel ... >> >> Uncompressing >> Linux........................................................................................................................ >> done, booting the kernel. >> >> <<-- NO more prinings -->> >> >> I just need to work with usb ethernet in 2.6.37... why does it fail with >> the kernel 2.6.37 ? >> >> Regards, >> Ran >> >> >> >> On Thu, Jan 15, 2015 at 7:14 PM, Ran Shalit <[email protected]> wrote: >> >>> Hi, >>> >>> Did anyone tried to work with the usb connector (the one that is marked >>> as "usb otg"), for ethernet with 2.6.37 ? >>> If not - maybe I should try use some older version for beagleboard ? >>> Regards, >>> Ran >>> >>> On Thu, Jan 15, 2015 at 6:36 PM, Ran Shalit <[email protected]> wrote: >>> >>>> Hi Robert, >>>> >>>> Thanks, >>>> I have compiled both modules and kernel, but still some error, without >>>> any information..... >>>> >>>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >>>> g_ether.ko >>>> insmod: error inserting 'g_ether.ko': -1 No such device >>>> >>>> The new boot log is below. >>>> >>>> Is there any idea why it fails ? >>>> >>>> Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >>>> Beagle Rev C5 >>>> Reading boot sector >>>> Loading u-boot.bin from mmc >>>> >>>> >>>> U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >>>> >>>> , CPU-OPP2 L3-165MHz >>>> OMAP3 Beagle board + LPDDR/NAND >>>> DRAM: 256 MB >>>> NAND: 512 MiB >>>> In: serial >>>> Out: serial >>>> Err: serial >>>> Board revision Ax/Bx >>>> Die ID #74aa000700000000015a676401014023 >>>> Hit any key to stop autoboot: 0 >>>> mmc1 is available >>>> reading uImage >>>> >>>> 2927348 bytes read >>>> ## Booting kernel from Legacy Image at 80300000 ... >>>> Image Name: Linux-2.6.37 >>>> Image Type: ARM Linux Kernel Image (uncompressed) >>>> Data Size: 2927284 Bytes = 2.8 MB >>>> Load Address: 80008000 >>>> Entry Point: 80008000 >>>> Verifying Checksum ... OK >>>> Loading Kernel Image ... OK >>>> OK >>>> >>>> Starting kernel ... >>>> >>>> Uncompressing Linux... done, booting the kernel. >>>> [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc >>>> version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #8 Thu Jan 15 18:29:23 IST >>>> 2015 >>>> [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >>>> cr=10c53c7f >>>> [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >>>> instruction cache >>>> [ 0.000000] Machine: OMAP3 Beagle Board >>>> [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >>>> [ 0.000000] Memory policy: ECC disabled, Data cache writeback >>>> [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) >>>> [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 >>>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >>>> Total pages: 64000 >>>> [ 0.000000] Kernel command line: console=ttyO2,115200n8 >>>> root=/dev/mmcblk0p2 rw rootwait >>>> [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >>>> [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 >>>> bytes) >>>> [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >>>> bytes) >>>> [ 0.000000] Memory: 252MB = 252MB total >>>> [ 0.000000] Memory: 242712k/242712k available, 19432k reserved, 0K >>>> highmem >>>> [ 0.000000] Virtual kernel memory layout: >>>> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >>>> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >>>> [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >>>> [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >>>> [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >>>> [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >>>> [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >>>> [ 0.000000] .text : 0xc003a000 - 0xc056e0d0 (5329 kB) >>>> [ 0.000000] .data : 0xc0570000 - 0xc0725220 (1749 kB) >>>> [ 0.000000] NR_IRQS:409 >>>> [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>>> [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >>>> [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >>>> [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >>>> [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >>>> [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >>>> interrupts >>>> [ 0.000000] Total of 96 interrupts on 1 active controller >>>> [ 0.000000] GPMC revision 5.0 >>>> [ 0.000000] Trying to install interrupt handler for IRQ402 >>>> [ 0.000000] Trying to install interrupt handler for IRQ403 >>>> [ 0.000000] Trying to install interrupt handler for IRQ404 >>>> [ 0.000000] Trying to install interrupt handler for IRQ405 >>>> [ 0.000000] Trying to install interrupt handler for IRQ406 >>>> [ 0.000000] Trying to install interrupt handler for IRQ407 >>>> [ 0.000000] Trying to install interrupt handler for IRQ408 >>>> [ 0.000000] Trying to install type control for IRQ409 >>>> [ 0.000000] Trying to set irq flags for IRQ409 >>>> [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >>>> [ 0.000000] Console: colour dummy device 80x30 >>>> [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >>>> Inc., Ingo Molnar >>>> [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >>>> [ 0.000000] ... MAX_LOCK_DEPTH: 48 >>>> [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >>>> [ 0.000000] ... CLASSHASH_SIZE: 4096 >>>> [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >>>> [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >>>> [ 0.000000] ... CHAINHASH_SIZE: 16384 >>>> [ 0.000000] memory used by lock dependency info: 3951 kB >>>> [ 0.000000] per task-struct memory footprint: 2304 bytes >>>> [ 0.000000] Calibrating delay loop... 458.96 BogoMIPS (lpj=1789952) >>>> [ 0.000000] pid_max: default: 32768 minimum: 301 >>>> [ 0.000000] Security Framework initialized >>>> [ 0.000000] Mount-cache hash table entries: 512 >>>> [ 0.000000] CPU: Testing write buffer coherency: ok >>>> [ 0.000000] devtmpfs: initialized >>>> [ 0.000000] regulator: core version 0.5 >>>> [ 0.000000] regulator: dummy: >>>> [ 0.000000] NET: Registered protocol family 16 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] OMAP GPIO hardware version 2.5 >>>> [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >>>> [ 0.000000] OMAP3 Beagle Rev: C4 >>>> [ 0.000000] Found NAND on CS0 >>>> [ 0.000000] Registering NAND on CS0 >>>> [ 0.000000] Unable to get DVI reset GPIO >>>> [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >>>> [ 0.000000] OMAP DMA hardware revision 4.0 >>>> [ 0.123657] bio: create slab <bio-0> at 0 >>>> [ 0.135101] SCSI subsystem initialized >>>> [ 0.149047] usbcore: registered new interface driver usbfs >>>> [ 0.151000] usbcore: registered new interface driver hub >>>> [ 0.152465] usbcore: registered new device driver usb >>>> [ 0.159149] omap_device: omap_i2c.1: new worst case activate latency >>>> 0: 61035 >>>> [ 0.159362] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >>>> [ 0.174316] twl4030: PIH (irq 7) chaining IRQs 368..375 >>>> [ 0.174560] twl4030: power (irq 373) chaining IRQs 376..383 >>>> [ 0.177703] twl4030: gpio (irq 368) chaining IRQs 384..401 >>>> [ 0.194580] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >>>> standby >>>> [ 0.198181] regulator: VDAC: 1800 mV normal standby >>>> [ 0.201873] regulator: VDVI: 1800 mV normal standby >>>> [ 0.205810] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >>>> standby >>>> [ 0.210021] regulator: VAUX3: 1800 mV normal standby >>>> [ 0.213623] regulator: VAUX4: 1800 mV normal standby >>>> [ 0.214294] omap_device: omap_i2c.1: new worst case deactivate >>>> latency 0: 91552 >>>> [ 0.214691] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >>>> [ 0.229003] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >>>> [ 0.239440] Advanced Linux Sound Architecture Driver Version 1.0.23. >>>> [ 0.244750] Switching to clocksource 32k_counter >>>> [ 0.435150] musb-hdrc: version 6.0, peripheral, debug=0 >>>> [ 0.435577] musb-hdrc musb-hdrc.0: degrade from otg to >>>> peripheral-only mode >>>> [ 0.435668] musb-hdrc musb-hdrc.0: dma type: dma-inventra >>>> [ 0.435699] HS USB OTG: no transceiver configured >>>> [ 0.435729] musb-hdrc musb-hdrc.0: musb_init_controller failed with >>>> status -19 >>>> [ 0.437591] NET: Registered protocol family 2 >>>> [ 0.438537] IP route cache hash table entries: 2048 (order: 1, 8192 >>>> bytes) >>>> [ 0.441192] TCP established hash table entries: 8192 (order: 4, >>>> 65536 bytes) >>>> [ 0.441772] TCP bind hash table entries: 8192 (order: 6, 360448 >>>> bytes) >>>> [ 0.447326] TCP: Hash tables configured (established 8192 bind 8192) >>>> [ 0.447509] TCP reno registered >>>> [ 0.447540] UDP hash table entries: 128 (order: 1, 12288 bytes) >>>> [ 0.448059] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) >>>> [ 0.449432] NET: Registered protocol family 1 >>>> [ 0.451385] RPC: Registered udp transport module. >>>> [ 0.451416] RPC: Registered tcp transport module. >>>> [ 0.451416] RPC: Registered tcp NFSv4.1 backchannel transport module. >>>> [ 0.452758] NetWinder Floating Point Emulator V0.97 (double >>>> precision) >>>> [ 0.456146] platform iva.0: Enabled OPP corresponding to 720MHz >>>> [ 0.460144] omap-iommu omap-iommu.0: isp registered >>>> [ 0.461303] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >>>> [ 0.649597] VFS: Disk quotas dquot_6.5.2 >>>> [ 0.649780] Dquot-cache hash table entries: 1024 (order 0, 4096 >>>> bytes) >>>> [ 0.653320] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red >>>> Hat, Inc. >>>> [ 0.657958] msgmni has been set to 474 >>>> [ 0.663879] io scheduler noop registered >>>> [ 0.663909] io scheduler deadline registered >>>> [ 0.664184] io scheduler cfq registered (default) >>>> [ 0.729553] OMAP DSS rev 2.0 >>>> [ 0.730224] OMAP DISPC rev 3.0 >>>> [ 0.730407] OMAP VENC rev 2 >>>> [ 0.731964] OMAP DSI rev 1.0 >>>> [ 1.061706] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >>>> [ 1.074340] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >>>> OMAP UART0 >>>> [ 1.077087] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >>>> OMAP UART1 >>>> [ 1.079193] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >>>> OMAP UART2 >>>> [ 1.822540] console [ttyO2] enabled >>>> [ 1.891143] brd: module loaded >>>> [ 1.925689] loop: module loaded >>>> [ 1.937622] mtdoops: mtd device (mtddev=name/number) must be supplied >>>> [ 1.944610] omap2-nand driver initializing >>>> [ 1.949676] ONFI flash detected >>>> [ 1.953247] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc >>>> (Micron ) >>>> [ 1.960388] Creating 5 MTD partitions on "omap2-nand.0": >>>> [ 1.966064] 0x000000000000-0x000000080000 : "X-Loader" >>>> [ 1.984436] 0x000000080000-0x000000260000 : "U-Boot" >>>> [ 1.999542] 0x000000260000-0x000000280000 : "U-Boot Env" >>>> [ 2.014068] 0x000000280000-0x000000680000 : "Kernel" >>>> [ 2.030242] 0x000000680000-0x000020000000 : "File System" >>>> [ 2.301544] OneNAND driver initializing >>>> [ 2.317413] mice: PS/2 mouse device common for all mice >>>> [ 2.327362] input: gpio-keys as >>>> /devices/platform/gpio-keys/input/input0 >>>> [ 2.345733] omap_device: omap_i2c.1: new worst case activate latency >>>> 0: 122070 >>>> [ 2.355102] input: twl4030_pwrbutton as >>>> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >>>> [ 2.374267] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>>> [ 2.381378] twl_rtc twl_rtc: Power up reset detected. >>>> [ 2.387847] twl_rtc twl_rtc: Enabling TWL-RTC. >>>> [ 2.395385] i2c /dev entries driver >>>> [ 2.407806] Linux media interface: v0.10 >>>> [ 2.413055] Linux video capture interface: v2.00 >>>> [ 2.420562] omap3isp supply VDD_CSIPHY1 not found, using dummy >>>> regulator >>>> [ 2.427795] omap3isp supply VDD_CSIPHY2 not found, using dummy >>>> regulator >>>> [ 2.435546] omap3isp omap3isp: Revision 2.0 found >>>> [ 2.440887] omap-iommu omap-iommu.0: isp: version 1.1 >>>> [ 2.552551] omap_i2c omap_i2c.2: Arbitration lost >>>> [ 2.573242] mt9v113 2-003c: chip id mismatch read 0x0, expecting >>>> 0x2280 >>>> [ 2.590240] isp_register_subdev_group: Unable to register subdev >>>> mt9v113 >>>> [ 2.598937] omap_device: omap_wdt.-1: new worst case activate >>>> latency 0: 30517 >>>> [ 2.609344] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>>> [ 2.615814] omap_device: omap_wdt.-1: new worst case deactivate >>>> latency 0: 30517 >>>> [ 2.625457] twl4030_wdt twl4030_wdt: Failed to register misc device >>>> [ 2.632202] twl4030_wdt: probe of twl4030_wdt failed with error -16 >>>> [ 2.661651] usbcore: registered new interface driver usbhid >>>> [ 2.667602] usbhid: USB HID core driver >>>> [ 2.679443] ALSA device list: >>>> [ 2.682678] No soundcards found. >>>> [ 2.686248] oprofile: hardware counters not available >>>> [ 2.691619] oprofile: using timer interrupt. >>>> [ 2.696716] TCP cubic registered >>>> [ 2.700225] Initializing XFRM netlink socket >>>> [ 2.704986] NET: Registered protocol family 17 >>>> [ 2.709930] NET: Registered protocol family 15 >>>> [ 2.715393] Registering the dns_resolver key type >>>> [ 2.721282] VFP support v0.3: implementor 41 architecture 3 part 30 >>>> variant c rev 1 >>>> [ 2.731414] ThumbEE CPU extension supported. >>>> [ 2.758483] Power Management for TI OMAP3. >>>> [ 2.763824] sr_init: No PMIC hook to init smartreflex >>>> [ 2.769836] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >>>> driver initialized >>>> [ 2.779174] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >>>> driver initialized >>>> [ 2.789276] SmartReflex Class3 initialized >>>> [ 2.857177] clock: disabling unused clocks to save power >>>> [ 2.866088] platform iva.0: omap_voltage_scale: Already at the >>>> requestedrate 360000000 >>>> [ 2.874511] platform mpu.0: omap_voltage_scale: Already at the >>>> requestedrate 500000000 >>>> [ 2.882934] platform l3_main.0: omap_voltage_scale: Already at the >>>> requestedrate 166000000 >>>> [ 2.927032] regulator_init_complete: incomplete constraints, leaving >>>> VDAC on >>>> [ 2.938446] twl_rtc twl_rtc: setting system clock to 2000-01-01 >>>> 00:00:00 UTC (946684800) >>>> [ 2.947753] omap_vout omap_vout: Buffer Size = 3686400 >>>> [ 2.957153] omap_vout omap_vout: : registered and initialized video >>>> device 15 >>>> [ 2.964782] omap_vout omap_vout: Buffer Size = 3686400 >>>> [ 2.973541] omap_vout omap_vout: : registered and initialized video >>>> device 16 >>>> [ 2.988342] Waiting for root device /dev/mmcblk0p2... >>>> [ 3.141418] mmc0: new high speed SDHC card at address aaaa >>>> [ 3.151336] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >>>> [ 3.175750] mmcblk0: p1 p2 >>>> [ 3.218505] EXT3-fs: barriers not enabled >>>> [ 3.227325] kjournald starting. Commit interval 5 seconds >>>> [ 3.233612] EXT3-fs (mmcblk0p2): warning: maximal mount count >>>> reached, running e2fsck is recommended >>>> [ 3.247222] EXT3-fs (mmcblk0p2): using internal journal >>>> [ 3.252807] EXT3-fs (mmcblk0p2): recovery complete >>>> [ 3.258544] EXT3-fs (mmcblk0p2): mounted filesystem with ordered >>>> data mode >>>> [ 3.266540] VFS: Mounted root (ext3 filesystem) on device 179:2. >>>> [ 3.273132] Freeing init memory: 200K >>>> Failed to open /dev/kmsg for logging: No such file or directory >>>> [ 3.609405] <30>systemd[1]: systemd 37 running in system mode. (+PAM >>>> +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >>>> >>>> Welcome to The ֵngstrצm Distribution! >>>> >>>> [ 3.713439] <28>systemd[1]: /sbin/modprobe failed with error code 1. >>>> [ 3.724670] <30>systemd[1]: Set hostname to <beagleboard>. >>>> Starting Runtime Directory... >>>> Starting Remount API VFS... >>>> Starting Lock Directory... >>>> Starting Media Directory... >>>> Started Apply Kernel Variables >>>> [ OK ] >>>> Started Huge Pages File System >>>> [ OK ] >>>> Starting POSIX Message Queue File System... >>>> Starting File System Check on Root Device... >>>> Started Load Kernel Modules >>>> [ OK ] >>>> Started Configuration File System >>>> [ OK ] >>>> Started FUSE Control File System >>>> [ OK ] >>>> Started Set Up Additional Binary Formats >>>> [ OK ] >>>> [ 4.677764] <30>systemd-fsck[593]: Root directory is writable, >>>> skipping check. >>>> Starting Debug File System... >>>> Started Security File System >>>> [ OK ] >>>> Starting Syslog Kernel Log Buffer Bridge... >>>> Started Syslog Kernel Log Buffer Bridge >>>> [ OK ] >>>> Starting udev Coldplug all Devices... >>>> Starting udev Kernel Device Manager... >>>> Started Runtime Directory >>>> [ OK ] >>>> Started Remount API VFS >>>> [ OK ] >>>> Started Lock Directory >>>> [ OK ] >>>> Started udev Ker[ 5.031005] <30>udevd[600]: starting version 175 >>>> nel Device Manager [ OK ] >>>> Started Media Directory >>>> [ OK ] >>>> Started POSIX Message Queue File System >>>> [ OK ] >>>> Started File System Check on Root Device >>>> [ OK ] >>>> Started Debug File System >>>> [ OK ] >>>> Starting Remount Root FS... >>>> Starting STDOUT Syslog Bridge... >>>> Started STDOUT Syslog Bridge >>>> [ OK ] >>>> Started Remount Root FS >>>> [ OK ] >>>> Started Opkg first boot configure >>>> [ OK ] >>>> Starting /tmp... >>>> Started Machine ID first boot configure >>>> [ OK ] >>>> Started /tmp >>>> [ OK ] >>>> Starting Load Random Seed... >>>> Starting Recreate Volatile Files and Directories... >>>> Started Load Random Seed >>>> [ OK ] >>>> Started Recreate Volatile Files and Directories >>>> [ OK ] >>>> Starting Console System Startup Logging... >>>> Starting xinetd.service... >>>> Started Angstrom LED config >>>> [ OK ] >>>> Starting Timestamping service... >>>> Started Timestamping service >>>> [ OK ] >>>> Starting Network Manager... >>>> Started SSH Key Generation >>>> [ OK ] >>>> Starting System Logging Service... >>>> Starting Permit User Sessions... >>>> Starting Login Service... >>>> Starting Avahi mDNS/DNS-SD Stack... >>>> Starting Periodic Command Scheduler... >>>> Started Periodic Command Scheduler >>>> [ OK ] >>>> Starting internet superserver: xinetdStarting D-Bus System Message >>>> Bus... >>>> Starting Disk Manager... >>>> Started Console System Startup Logging >>>> [ OK ] >>>> [ 8.354309] <27>systemd-logind[707]: Failed to open >>>> /sys/class/tty/tty0/active: No such file or directory >>>> Started Permit User Sessions >>>> [ OK ] >>>> [ 8.659515] <27>systemd-logind[707]: Failed to fully start up >>>> daemon: No such file or directory >>>> [ 8.877380] <29>systemd[1]: systemd-logind.service: main process >>>> exited, code=exited, status=1 >>>> [ 9.057952] <75>/usr/sbin/crond[722]: (CRON) INFO (Syslog will be >>>> used instead of sendmail.): No such file or directory >>>> . >>>> Failed to start Login Service >>>> [FAILED] >>>> [ 9.415985] <30>avahi-daemon[711]: Found user 'avahi' (UID 998) and >>>> group 'avahi' (GID 996). >>>> [ 9.478942] <30>avahi-daemon[711]: Successfully dropped root >>>> privileges. >>>> See 'systemctl status systemd-logind.service' for details. >>>> [ 9.517791] <29>systemd[1]: Unit systemd-logind.service entered >>>> failed state. >>>> [ 9.659942] <30>avahi-daemon[711]: avahi-daemon 0.6.30 starting up. >>>> Started xinetd.service >>>> [ OK ] >>>> [ 9.930999] <26>xinetd[868]: 868 {init_services} no services. >>>> Exiting... >>>> Starting Serial Getty on ttyO2... >>>> [ 10.786376] <30>NetworkManager[704]: NetworkManager[704]: <info> >>>> NetworkManager (version 0.9.2.0) is starting... >>>> Started Serial Getty on ttyO2 >>>> [ OK ] >>>> [ 11.033538] <30>udisks-daemon[770]: (process:770): GLib-WARNING **: >>>> goption.c:2168: ignoring no-arg, optional-arg or filename flags (16) on >>>> option of type 1 >>>> [ 11.310058] <14>NetworkManager[704]: <info> NetworkManager (version >>>> 0.9.2.0) is starting... >>>> Started D-Bus System Message Bus >>>> [ OK ] >>>> [ 11.474243] <30>NetworkManager[704]: NetworkManager[704]: <info> >>>> Read config file (null) >>>> [ 11.721771] <14>NetworkManager[704]: <info> Read config file (null) >>>> [ 11.728485] <30>load-timestamp.sh[702]: Update systemtime from >>>> /etc/timestamp >>>> [ 12.190551] <30>load-timestamp.sh[702]: Thu Jan 12 12:19:00 UTC 2012 >>>> [ 12.656372] <27>systemd-uaccess[1031]: Failed to apply ACL on >>>> /dev/v4l-subdev3: Operation not supported >>>> [ 12.891265] <27>systemd-uaccess[1027]: Failed to apply ACL on >>>> /dev/v4l-subdev0: Operation not supported >>>> >>>> .---O---. [ 13.117218] >>>> <27>systemd-uaccess[1019]: Failed to apply ACL on /dev/v4l-subdev1: >>>> Operation not supported >>>> >>>> | | .-. o o >>>> | | |-----.-----.-[ 13.337951] <27>systemd-uaccess[1033]: Failed >>>> to apply ACL on /dev/v4l-subdev2: Operation not supported >>>> ----.| | .----..--[ 13.378295] <27>systemd-uaccess[1037]: Failed to >>>> apply ACL on /dev/v4l-subdev6: Operation not supported >>>> ---.-----. >>>> | | | __ | ---'| '--.| .-'| | | >>>> | | | | | |--- [ 13.526580] <27>systemd-uaccess[1040]: >>>> Failed to apply ACL on /dev/v4l-subdev7: Operation not supported >>>> || --'| | | ' | | | | >>>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>>> [ 13.677337] <27>systemd-uaccess[1028]: Failed to apply ACL on >>>> /dev/v4l-subdev5: Operation not supported >>>> -' | >>>> '---' >>>> >>>> The Angstrom Distribution beagleboard ttyO2 >>>> >>>> Angstrom v2012.01-co[ 13.979644] <27>systemd-uaccess[1042]: Failed to >>>> apply ACL on /dev/v4l-subdev4: Operation not supported >>>> re - Kernel 2.6.37 >>>> >>>> beagleboard login: [ 14.332580] <27>systemd-uaccess[1049]: Failed to >>>> apply ACL on /dev/video0: Operation not supported >>>> [ 14.667114] <27>systemd-uaccess[1051]: Failed to apply ACL on >>>> /dev/video1: Operation not supported >>>> [ 14.995208] <27>systemd-uaccess[1053]: Failed to apply ACL on >>>> /dev/video3: Operation not supported >>>> Started udev Coldplug all Devices >>>> [ OK ] >>>> >>>> [ 15.218170] <27>systemd-uaccess[1055]: Failed to apply ACL on >>>> /dev/video2: Operation not supported >>>> [ 15.450988] <27>systemd-uaccess[1057]: Failed to apply ACL on >>>> /dev/video4: Operation not supported >>>> Started Disk Manager >>>> [ OK ] >>>> >>>> Started Avahi mDNS/DNS-SD Stack >>>> [[ 15.689880] <27> OK ] >>>> systemd-uaccess[1063]: Failed to apply ACL on >>>> /dev/video5: Operation not supported >>>> [ 15.800720] <27>systemd-uaccess[1073]: Failed to apply ACL on >>>> /dev/video8: Operation not supported >>>> [ 16.030517] <27>systemd-uaccess[1072]: Failed to apply ACL on >>>> /dev/video7: Operation not supported >>>> [ 16.091583] <27>systemd-uaccess[1086]: Failed to apply ACL on >>>> /dev/video6: Operation not supported >>>> Stopping Syslog Kernel Log Buffer Bridge... >>>> [ 16.201354] >>>> <30>udisks-daemon[770]: (udisks-daemon:770): udisks-daemon-DEBUG: Starting >>>> daemon version 1.0.4 >>>> [ 16.326660] <30>avahi-daemon[711]: Successfully called chroot(). >>>> [ 16.400512] <30>avahi-daemon[711]: Successfully dropped remaining >>>> capabilities. >>>> [ 16.473449] <30>avahi-daemon[711]: Loading service file >>>> /services/sftp-ssh.service. >>>> [ 16.510803] <30>avahi-daemon[711]: Loading service file >>>> /services/ssh.service. >>>> [ 16.565338] <30>avahi-daemon[711]: Loading service file >>>> /services/udisks.service. >>>> [ 16.644561] <30>avahi-daemon[711]: Network interface enumeration >>>> completed. >>>> [ 16.669464] <30>avahi-daemon[711]: Registering HINFO record with >>>> values 'ARMV7L'/'LINUX'. >>>> [ 16.757904] <30>avahi-daemon[711]: Server startup complete. Host >>>> name is beagleboard.local. Local service cookie is 441939348. >>>> Starting Getty on tty1... >>>> [ 16.862426] <30>avahi-daemon[711]: Service >>>> "beagleboard" (/services/udisks.service) successfully established. >>>> [ 16.971832] <30>dbus-daemon[969]: dbus[969]: [system] Activating >>>> service name='org.freedesktop.PolicyKit1' (using servicehelper) >>>> Started Getty on tty1 >>>> [ OK ] >>>> >>>> [ 17.104522] <29>dbus[969]: [system] Activating service >>>> name='org.freedesktop.PolicyKit1' (using servicehelper) >>>> [ 17.218292] <30>avahi-daemon[711]: Service "beagleboard" >>>> (/services/ssh.service) successfully established. >>>> Starting Gnome D[ 17.271667] <27>isplay Manager..systemd-uaccess. >>>> >>>> [1199]: Failed to apply ACL on /dev/snd/timer: Operation not supported >>>> [ 17.293273] <30>avahi-daemon[711]: Service "beagleboard" >>>> (/services/sftp-ssh.service) successfully established. >>>> Started Gnome Display Manager >>>> [ OK ] >>>> >>>> Stopped Syslog Kernel Log Buffer Bridge >>>> [ OK ] >>>> >>>> Started System Logging Service >>>> [ OK ] >>>> >>>> Started Network Manager >>>> [ OK ] >>>> >>>> .---O---. >>>> | | .-. o o >>>> | | |-----.-----.-----.| | .----..-----.-----. >>>> | | | __ | ---'| '--.| .-'| | | >>>> | | | | | |--- || --'| | | ' | | | | >>>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>>> -' | >>>> '---' >>>> >>>> The Angstrom Distribution beagleboard ttyO2 >>>> >>>> Angstrom v2012.01-core - Kernel 2.6.37 >>>> >>>> beagleboard login: >>>> .---O---. >>>> | | .-. o o >>>> | | |-----.-----.-----.| | .----..-----.-----. >>>> | | | __ | ---'| '--.| .-'| | | >>>> | | | | | |--- || --'| | | ' | | | | >>>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>>> -' | >>>> '---' >>>> >>>> The Angstrom Distribution beagleboard ttyO2 >>>> >>>> Angstrom v2012.01-core - Kernel 2.6.37 >>>> >>>> beagleboard login: root >>>> Last login: Thu Jan 12 12:19:48 GMT 2012 on ttyO2 >>>> root@beagleboard:~# >>>> root@beagleboard:~# >>>> root@beagleboard:~# cd /lib/modules/2.6.37/kernel/drivers/usb/gadget/ >>>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >>>> g_ether.ko >>>> insmod: error inserting 'g_ether.ko': -1 No such device >>>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget >>>> >>>> Regards, >>>> Ran >>>> >>>> >>>> On Thu, Jan 15, 2015 at 6:26 PM, Robert Nelson <[email protected] >>>> > wrote: >>>> >>>>> On Thu, Jan 15, 2015 at 10:23 AM, Ran Shalit <[email protected]> >>>>> wrote: >>>>> > Hi Robert, >>>>> > >>>>> > Thank you very much. >>>>> > I was lazy not to notice that.... >>>>> > It now seems better (less errors on boot), but still fails with same >>>>> error: >>>>> > insmod: error inserting 'g_ether.ko': -1 No such device >>>>> > Can you give me another hint what might cause such failure? >>>>> > >>>>> > This is the boot log: >>>>> > >>>>> > Last login: Thu Jan 12 12:31:58 GMT 2012 on ttyO2 >>>>> > root@beagleboard:~# >>>>> > root@beagleboard:~# >>>>> > root@beagleboard:~# >>>>> > root@beagleboard:~# modprobe g_ether >>>>> > [ 30.667053] g_ether: disagrees about version of symbol >>>>> module_layout >>>>> > FATAL: Error inserting g_ether >>>>> >>>>> This means your kernel was built seperatly from the modules.. >>>>> >>>>> When you build your kernel, just also build 'make modules' and install >>>>> them to the rootfs.. >>>>> >>>>> >>>>> > (/lib/modules/2.6.37/kernel/drivers/usb/gadget/g_ether.ko): Invalid >>>>> module >>>>> > format >>>>> > root@beagleboard:~# d >>>>> > >>>>> > Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >>>>> > Beagle Rev C5 >>>>> > Reading boot sector >>>>> > Loading u-boot.bin from mmc >>>>> > >>>>> > >>>>> > U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >>>>> > >>>>> > , CPU-OPP2 L3-165MHz >>>>> > OMAP3 Beagle board + LPDDR/NAND >>>>> > DRAM: 256 MB >>>>> > NAND: 512 MiB >>>>> > In: serial >>>>> > Out: serial >>>>> > Err: serial >>>>> > Board revision Ax/Bx >>>>> > Die ID #74aa000700000000015a676401014023 >>>>> > Hit any key to stop autoboot: 0 >>>>> > mmc1 is available >>>>> > reading uImage >>>>> > >>>>> > 2918324 bytes read >>>>> > ## Booting kernel from Legacy Image at 80300000 ... >>>>> > Image Name: Linux-2.6.37 >>>>> > Image Type: ARM Linux Kernel Image (uncompressed) >>>>> > Data Size: 2918260 Bytes = 2.8 MB >>>>> > Load Address: 80008000 >>>>> > Entry Point: 80008000 >>>>> > Verifying Checksum ... OK >>>>> > Loading Kernel Image ... OK >>>>> > OK >>>>> > >>>>> > Starting kernel ... >>>>> > >>>>> > Uncompressing Linux... done, booting the kernel. >>>>> > [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc >>>>> version >>>>> > 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #7 Thu Jan 15 18:09:40 IST >>>>> 2015 >>>>> > [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >>>>> > cr=10c53c7f >>>>> > [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >>>>> > instruction cache >>>>> > [ 0.000000] Machine: OMAP3 Beagle Board >>>>> > [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >>>>> > [ 0.000000] Memory policy: ECC disabled, Data cache writeback >>>>> > [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp >>>>> 720mhz ) >>>>> > [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: >>>>> 0x10000 >>>>> > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping >>>>> on. Total >>>>> > pages: 64000 >>>>> > [ 0.000000] Kernel command line: console=ttyO2,115200n8 >>>>> > root=/dev/mmcblk0p2 rw rootwait >>>>> > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >>>>> > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, >>>>> 131072 >>>>> > bytes) >>>>> > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, >>>>> 65536 bytes) >>>>> > [ 0.000000] Memory: 252MB = 252MB total >>>>> > [ 0.000000] Memory: 242740k/242740k available, 19404k reserved, 0K >>>>> > highmem >>>>> > [ 0.000000] Virtual kernel memory layout: >>>>> > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >>>>> > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >>>>> > [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >>>>> > [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >>>>> > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >>>>> > [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >>>>> > [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >>>>> > [ 0.000000] .text : 0xc003a000 - 0xc0568f4c (5308 kB) >>>>> > [ 0.000000] .data : 0xc056a000 - 0xc071f1a0 (1749 kB) >>>>> > [ 0.000000] NR_IRQS:409 >>>>> > [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>>>> > [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >>>>> > [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >>>>> > [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >>>>> > [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >>>>> > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with >>>>> 96 >>>>> > interrupts >>>>> > [ 0.000000] Total of 96 interrupts on 1 active controller >>>>> > [ 0.000000] GPMC revision 5.0 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ402 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ403 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ404 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ405 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ406 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ407 >>>>> > [ 0.000000] Trying to install interrupt handler for IRQ408 >>>>> > [ 0.000000] Trying to install type control for IRQ409 >>>>> > [ 0.000000] Trying to set irq flags for IRQ409 >>>>> > [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >>>>> > [ 0.000000] Console: colour dummy device 80x30 >>>>> > [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red >>>>> Hat, Inc., >>>>> > Ingo Molnar >>>>> > [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >>>>> > [ 0.000000] ... MAX_LOCK_DEPTH: 48 >>>>> > [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >>>>> > [ 0.000000] ... CLASSHASH_SIZE: 4096 >>>>> > [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >>>>> > [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >>>>> > [ 0.000000] ... CHAINHASH_SIZE: 16384 >>>>> > [ 0.000000] memory used by lock dependency info: 3951 kB >>>>> > [ 0.000000] per task-struct memory footprint: 2304 bytes >>>>> > [ 0.000000] Calibrating delay loop... 456.86 BogoMIPS >>>>> (lpj=1781760) >>>>> > [ 0.000000] pid_max: default: 32768 minimum: 301 >>>>> > [ 0.000000] Security Framework initialized >>>>> > [ 0.000000] Mount-cache hash table entries: 512 >>>>> > [ 0.000000] CPU: Testing write buffer coherency: ok >>>>> > [ 0.000000] devtmpfs: initialized >>>>> > [ 0.000000] regulator: core version 0.5 >>>>> > [ 0.000000] regulator: dummy: >>>>> > [ 0.000000] NET: Registered protocol family 16 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>>> > [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >>>>> > [ 0.000000] OMAP3 Beagle Rev: C4 >>>>> > [ 0.000000] Found NAND on CS0 >>>>> > [ 0.000000] Registering NAND on CS0 >>>>> > [ 0.000000] Unable to get DVI reset GPIO >>>>> > [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >>>>> > [ 0.000000] OMAP DMA hardware revision 4.0 >>>>> > [ 0.122314] bio: create slab <bio-0> at 0 >>>>> > [ 0.133697] SCSI subsystem initialized >>>>> > [ 0.147491] usbcore: registered new interface driver usbfs >>>>> > [ 0.149322] usbcore: registered new interface driver hub >>>>> > [ 0.150878] usbcore: registered new device driver usb >>>>> > [ 0.157501] omap_device: omap_i2c.1: new worst case activate >>>>> latency 0: >>>>> > 30517 >>>>> > [ 0.157684] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >>>>> > [ 0.172485] twl4030: PIH (irq 7) chaining IRQs 368..375 >>>>> > [ 0.172729] twl4030: power (irq 373) chaining IRQs 376..383 >>>>> > [ 0.175842] twl4030: gpio (irq 368) chaining IRQs 384..401 >>>>> > [ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >>>>> standby >>>>> > [ 0.196044] regulator: VDAC: 1800 mV normal standby >>>>> > [ 0.199615] regulator: VDVI: 1800 mV normal standby >>>>> > [ 0.203613] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >>>>> standby >>>>> > [ 0.207763] regulator: VAUX3: 1800 mV normal standby >>>>> > [ 0.211334] regulator: VAUX4: 1800 mV normal standby >>>>> > [ 0.211914] omap_device: omap_i2c.1: new worst case deactivate >>>>> latency 0: >>>>> > 61035 >>>>> > [ 0.221954] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >>>>> > [ 0.236083] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >>>>> > [ 0.246398] Advanced Linux Sound Architecture Driver Version >>>>> 1.0.23. >>>>> > [ 0.251586] Switching to clocksource 32k_counter >>>>> > [ 0.440246] musb-hdrc: version 6.0, peripheral, debug=0 >>>>> > [ 0.440673] musb-hdrc musb-hdrc.0: degrade from otg to >>>>> peripheral-only >>>>> > mode >>>>> > [ 0.440795] musb-hdrc musb-hdrc.0: dma type: dma-inventra >>>>> > [ 0.440826] HS USB OTG: no transceiver configured >>>>> > [ 0.440856] musb-hdrc musb-hdrc.0: musb_init_controller failed >>>>> with >>>>> > status -19 >>>>> > [ 0.442718] NET: Registered protocol family 2 >>>>> > [ 0.443664] IP route cache hash table entries: 2048 (order: 1, >>>>> 8192 >>>>> > bytes) >>>>> > [ 0.446136] TCP established hash table entries: 8192 (order: 4, >>>>> 65536 >>>>> > bytes) >>>>> > [ 0.446746] TCP bind hash table entries: 8192 (order: 6, 360448 >>>>> bytes) >>>>> > [ 0.452423] TCP: Hash tables configured (established 8192 bind >>>>> 8192) >>>>> > [ 0.452545] TCP reno registered >>>>> > [ 0.452606] UDP hash table entries: 128 (order: 1, 12288 bytes) >>>>> > [ 0.453033] UDP-Lite hash table entries: 128 (order: 1, 12288 >>>>> bytes) >>>>> > [ 0.454437] NET: Registered protocol family 1 >>>>> > [ 0.456481] RPC: Registered udp transport module. >>>>> > [ 0.456512] RPC: Registered tcp transport module. >>>>> > [ 0.456542] RPC: Registered tcp NFSv4.1 backchannel transport >>>>> module. >>>>> > [ 0.457855] NetWinder Floating Point Emulator V0.97 (double >>>>> precision) >>>>> > [ 0.461059] platform iva.0: Enabled OPP corresponding to 720MHz >>>>> > [ 0.465179] omap-iommu omap-iommu.0: isp registered >>>>> > [ 0.466308] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >>>>> > [ 0.654205] VFS: Disk quotas dquot_6.5.2 >>>>> > [ 0.654388] Dquot-cache hash table entries: 1024 (order 0, 4096 >>>>> bytes) >>>>> > [ 0.657714] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red >>>>> Hat, >>>>> > Inc. >>>>> > [ 0.659271] msgmni has been set to 474 >>>>> > [ 0.665100] io scheduler noop registered >>>>> > [ 0.665191] io scheduler deadline registered >>>>> > [ 0.665435] io scheduler cfq registered (default) >>>>> > [ 0.728576] OMAP DSS rev 2.0 >>>>> > [ 0.729248] OMAP DISPC rev 3.0 >>>>> > [ 0.729431] OMAP VENC rev 2 >>>>> > [ 0.730957] OMAP DSI rev 1.0 >>>>> > [ 1.060791] Serial: 8250/16550 driver, 4 ports, IRQ sharing >>>>> enabled >>>>> > [ 1.073242] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >>>>> OMAP >>>>> > UART0 >>>>> > [ 1.076141] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >>>>> OMAP >>>>> > UART1 >>>>> > [ 1.078155] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >>>>> OMAP >>>>> > UART2 >>>>> > [ 1.821472] console [ttyO2] enabled >>>>> > [ 1.889343] brd: module loaded >>>>> > [ 1.923370] loop: module loaded >>>>> > [ 1.935363] mtdoops: mtd device (mtddev=name/number) must be >>>>> supplied >>>>> > [ 1.942352] omap2-nand driver initializing >>>>> > [ 1.947479] ONFI flash detected >>>>> > [ 1.951019] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc >>>>> (Micron ) >>>>> > [ 1.958160] Creating 5 MTD partitions on "omap2-nand.0": >>>>> > [ 1.963836] 0x000000000000-0x000000080000 : "X-Loader" >>>>> > [ 1.982055] 0x000000080000-0x000000260000 : "U-Boot" >>>>> > [ 1.997100] 0x000000260000-0x000000280000 : "U-Boot Env" >>>>> > [ 2.011535] 0x000000280000-0x000000680000 : "Kernel" >>>>> > [ 2.027618] 0x000000680000-0x000020000000 : "File System" >>>>> > [ 2.298248] OneNAND driver initializing >>>>> > [ 2.315246] mice: PS/2 mouse device common for all mice >>>>> > [ 2.324920] input: gpio-keys as >>>>> /devices/platform/gpio-keys/input/input0 >>>>> > [ 2.343780] omap_device: omap_i2c.1: new worst case activate >>>>> latency 0: >>>>> > 91552 >>>>> > [ 2.352966] input: twl4030_pwrbutton as >>>>> > >>>>> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >>>>> > [ 2.372009] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>>>> > [ 2.379119] twl_rtc twl_rtc: Power up reset detected. >>>>> > [ 2.385589] twl_rtc twl_rtc: Enabling TWL-RTC. >>>>> > [ 2.393066] i2c /dev entries driver >>>>> > [ 2.405456] Linux media interface: v0.10 >>>>> > [ 2.410736] Linux video capture interface: v2.00 >>>>> > [ 2.418273] omap3isp supply VDD_CSIPHY1 not found, using dummy >>>>> regulator >>>>> > [ 2.425506] omap3isp supply VDD_CSIPHY2 not found, using dummy >>>>> regulator >>>>> > [ 2.433227] omap3isp omap3isp: Revision 2.0 found >>>>> > [ 2.438476] omap-iommu omap-iommu.0: isp: version 1.1 >>>>> > [ 2.559204] omap_i2c omap_i2c.2: Arbitration lost >>>>> > [ 2.580078] mt9v113 2-003c: chip id mismatch read 0x0, expecting >>>>> 0x2280 >>>>> > [ 2.597198] isp_register_subdev_group: Unable to register subdev >>>>> mt9v113 >>>>> > [ 2.605865] omap_device: omap_wdt.-1: new worst case activate >>>>> latency 0: >>>>> > 30517 >>>>> > [ 2.616241] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>>>> > [ 2.622711] omap_device: omap_wdt.-1: new worst case deactivate >>>>> latency >>>>> > 0: 30517 >>>>> > [ 2.632354] twl4030_wdt twl4030_wdt: Failed to register misc >>>>> device >>>>> > [ 2.639099] twl4030_wdt: probe of twl4030_wdt failed with error >>>>> -16 >>>>> > [ 2.668334] usbcore: registered new interface driver usbhid >>>>> > [ 2.674285] usbhid: USB HID core driver >>>>> > [ 2.686126] ALSA device list: >>>>> > [ 2.689392] No soundcards found. >>>>> > [ 2.692962] oprofile: hardware counters not available >>>>> > [ 2.698333] oprofile: using timer interrupt. >>>>> > [ 2.703430] TCP cubic registered >>>>> > [ 2.706939] Initializing XFRM netlink socket >>>>> > [ 2.711639] NET: Registered protocol family 17 >>>>> > [ 2.716613] NET: Registered protocol family 15 >>>>> > [ 2.722045] Registering the dns_resolver key type >>>>> > [ 2.727783] VFP support v0.3: implementor 41 architecture 3 part >>>>> 30 >>>>> > variant c rev 1 >>>>> > [ 2.737945] ThumbEE CPU extension supported. >>>>> > [ 2.764984] Power Management for TI OMAP3. >>>>> > [ 2.770355] sr_init: No PMIC hook to init smartreflex >>>>> > [ 2.776336] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >>>>> driver >>>>> > initialized >>>>> > [ 2.785644] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >>>>> driver >>>>> > initialized >>>>> > [ 2.795776] SmartReflex Class3 initialized >>>>> > [ 2.863677] clock: disabling unused clocks to save power >>>>> > [ 2.872497] platform iva.0: omap_voltage_scale: Already at the >>>>> > requestedrate 360000000 >>>>> > [ 2.880920] platform mpu.0: omap_voltage_scale: Already at the >>>>> > requestedrate 500000000 >>>>> > [ 2.889343] platform l3_main.0: omap_voltage_scale: Already at the >>>>> > requestedrate 166000000 >>>>> > [ 2.931488] omap_device: omap_i2c.1: new worst case deactivate >>>>> latency 0: >>>>> > 122070 >>>>> > [ 2.940246] regulator_init_complete: incomplete constraints, >>>>> leaving VDAC >>>>> > on >>>>> > [ 2.952911] twl_rtc twl_rtc: setting system clock to 2000-01-01 >>>>> 00:00:00 >>>>> > UTC (946684800) >>>>> > [ 2.962005] omap_vout omap_vout: Buffer Size = 3686400 >>>>> > [ 2.971313] omap_vout omap_vout: : registered and initialized >>>>> video >>>>> > device 15 >>>>> > [ 2.978973] omap_vout omap_vout: Buffer Size = 3686400 >>>>> > [ 2.987640] omap_vout omap_vout: : registered and initialized >>>>> video >>>>> > device 16 >>>>> > [ 3.002319] Waiting for root device /dev/mmcblk0p2... >>>>> > [ 3.166046] mmc0: new high speed SDHC card at address aaaa >>>>> > [ 3.175537] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >>>>> > [ 3.200164] mmcblk0: p1 p2 >>>>> > [ 3.232910] EXT3-fs: barriers not enabled >>>>> > [ 3.312805] kjournald starting. Commit interval 5 seconds >>>>> > [ 3.319183] EXT3-fs (mmcblk0p2): warning: maximal mount count >>>>> reached, >>>>> > running e2fsck is recommended >>>>> > [ 3.333465] EXT3-fs (mmcblk0p2): using internal journal >>>>> > [ 3.339080] EXT3-fs (mmcblk0p2): recovery complete >>>>> > [ 3.347442] EXT3-fs (mmcblk0p2): mounted filesystem with ordered >>>>> data >>>>> > mode >>>>> > [ 3.355468] VFS: Mounted root (ext3 filesystem) on device 179:2. >>>>> > [ 3.362091] Freeing init memory: 200K >>>>> > Failed to open /dev/kmsg for logging: No such file or directory >>>>> > [ 3.685821] <30>systemd[1]: systemd 37 running in system mode. >>>>> (+PAM >>>>> > +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >>>>> > >>>>> > Welcome to The ֵngstrצm Distribution! >>>>> > >>>>> > [ 3.784942] <28>systemd[1]: /sbin/modprobe failed with error code >>>>> 1. >>>>> > [ 3.796173] <30>systemd[1]: Set hostname to <beagleboard>. >>>>> > [ 4.271270] <27>systemd[1]: Failed to open /dev/autofs: No such >>>>> file or >>>>> > directory >>>>> >>>>> add: CONFIG_AUTOFS4_FS=y >>>>> >>>>> Regards, >>>>> >>>>> -- >>>>> Robert Nelson >>>>> http://www.rcn-ee.com/ >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to a topic in the >>>>> Google Groups "BeagleBoard" group. >>>>> To unsubscribe from this topic, visit >>>>> https://groups.google.com/d/topic/beagleboard/RznTdyaz2gg/unsubscribe. >>>>> To unsubscribe from this group and all its topics, send an email to >>>>> [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> >>> >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
