Hello, Can anyone please try to see if he can work with usb otg and beagleboard this is the download page for kernel 2.6.37 I use: http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/OMAP_04_02/04_02_00_07/index_FDS.html
Regards, Ran On Thu, Jan 15, 2015 at 8:16 PM, Ran Shalit <[email protected]> wrote: > Hi, > > When I compiled earlier kernel version which are supposed to support > OMAP3530 with beaglebone I fail to start kernel (psp 3.0.1.6, kernel > 2.6.32); > > 1920736 bytes read > ## Booting kernel from Legacy Image at 80300000 ... > Image Name: Linux-2.6.32 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 1920672 Bytes = 1.8 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing > Linux........................................................................................................................ > done, booting the kernel. > > <<-- NO more prinings -->> > > I just need to work with usb ethernet in 2.6.37... why does it fail with > the kernel 2.6.37 ? > > Regards, > Ran > > > > On Thu, Jan 15, 2015 at 7:14 PM, Ran Shalit <[email protected]> wrote: > >> Hi, >> >> Did anyone tried to work with the usb connector (the one that is marked >> as "usb otg"), for ethernet with 2.6.37 ? >> If not - maybe I should try use some older version for beagleboard ? >> Regards, >> Ran >> >> On Thu, Jan 15, 2015 at 6:36 PM, Ran Shalit <[email protected]> wrote: >> >>> Hi Robert, >>> >>> Thanks, >>> I have compiled both modules and kernel, but still some error, without >>> any information..... >>> >>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >>> g_ether.ko >>> insmod: error inserting 'g_ether.ko': -1 No such device >>> >>> The new boot log is below. >>> >>> Is there any idea why it fails ? >>> >>> Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >>> Beagle Rev C5 >>> Reading boot sector >>> Loading u-boot.bin from mmc >>> >>> >>> U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >>> >>> , CPU-OPP2 L3-165MHz >>> OMAP3 Beagle board + LPDDR/NAND >>> DRAM: 256 MB >>> NAND: 512 MiB >>> In: serial >>> Out: serial >>> Err: serial >>> Board revision Ax/Bx >>> Die ID #74aa000700000000015a676401014023 >>> Hit any key to stop autoboot: 0 >>> mmc1 is available >>> reading uImage >>> >>> 2927348 bytes read >>> ## Booting kernel from Legacy Image at 80300000 ... >>> Image Name: Linux-2.6.37 >>> Image Type: ARM Linux Kernel Image (uncompressed) >>> Data Size: 2927284 Bytes = 2.8 MB >>> Load Address: 80008000 >>> Entry Point: 80008000 >>> Verifying Checksum ... OK >>> Loading Kernel Image ... OK >>> OK >>> >>> Starting kernel ... >>> >>> Uncompressing Linux... done, booting the kernel. >>> [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc version >>> 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #8 Thu Jan 15 18:29:23 IST 2015 >>> [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >>> cr=10c53c7f >>> [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >>> instruction cache >>> [ 0.000000] Machine: OMAP3 Beagle Board >>> [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >>> [ 0.000000] Memory policy: ECC disabled, Data cache writeback >>> [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz ) >>> [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 >>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >>> Total pages: 64000 >>> [ 0.000000] Kernel command line: console=ttyO2,115200n8 >>> root=/dev/mmcblk0p2 rw rootwait >>> [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >>> [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 >>> bytes) >>> [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >>> bytes) >>> [ 0.000000] Memory: 252MB = 252MB total >>> [ 0.000000] Memory: 242712k/242712k available, 19432k reserved, 0K >>> highmem >>> [ 0.000000] Virtual kernel memory layout: >>> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >>> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >>> [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >>> [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >>> [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >>> [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >>> [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >>> [ 0.000000] .text : 0xc003a000 - 0xc056e0d0 (5329 kB) >>> [ 0.000000] .data : 0xc0570000 - 0xc0725220 (1749 kB) >>> [ 0.000000] NR_IRQS:409 >>> [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>> [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >>> [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >>> [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >>> [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >>> [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >>> interrupts >>> [ 0.000000] Total of 96 interrupts on 1 active controller >>> [ 0.000000] GPMC revision 5.0 >>> [ 0.000000] Trying to install interrupt handler for IRQ402 >>> [ 0.000000] Trying to install interrupt handler for IRQ403 >>> [ 0.000000] Trying to install interrupt handler for IRQ404 >>> [ 0.000000] Trying to install interrupt handler for IRQ405 >>> [ 0.000000] Trying to install interrupt handler for IRQ406 >>> [ 0.000000] Trying to install interrupt handler for IRQ407 >>> [ 0.000000] Trying to install interrupt handler for IRQ408 >>> [ 0.000000] Trying to install type control for IRQ409 >>> [ 0.000000] Trying to set irq flags for IRQ409 >>> [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >>> [ 0.000000] Console: colour dummy device 80x30 >>> [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >>> Inc., Ingo Molnar >>> [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >>> [ 0.000000] ... MAX_LOCK_DEPTH: 48 >>> [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >>> [ 0.000000] ... CLASSHASH_SIZE: 4096 >>> [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >>> [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >>> [ 0.000000] ... CHAINHASH_SIZE: 16384 >>> [ 0.000000] memory used by lock dependency info: 3951 kB >>> [ 0.000000] per task-struct memory footprint: 2304 bytes >>> [ 0.000000] Calibrating delay loop... 458.96 BogoMIPS (lpj=1789952) >>> [ 0.000000] pid_max: default: 32768 minimum: 301 >>> [ 0.000000] Security Framework initialized >>> [ 0.000000] Mount-cache hash table entries: 512 >>> [ 0.000000] CPU: Testing write buffer coherency: ok >>> [ 0.000000] devtmpfs: initialized >>> [ 0.000000] regulator: core version 0.5 >>> [ 0.000000] regulator: dummy: >>> [ 0.000000] NET: Registered protocol family 16 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] OMAP GPIO hardware version 2.5 >>> [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >>> [ 0.000000] OMAP3 Beagle Rev: C4 >>> [ 0.000000] Found NAND on CS0 >>> [ 0.000000] Registering NAND on CS0 >>> [ 0.000000] Unable to get DVI reset GPIO >>> [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >>> [ 0.000000] OMAP DMA hardware revision 4.0 >>> [ 0.123657] bio: create slab <bio-0> at 0 >>> [ 0.135101] SCSI subsystem initialized >>> [ 0.149047] usbcore: registered new interface driver usbfs >>> [ 0.151000] usbcore: registered new interface driver hub >>> [ 0.152465] usbcore: registered new device driver usb >>> [ 0.159149] omap_device: omap_i2c.1: new worst case activate latency >>> 0: 61035 >>> [ 0.159362] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >>> [ 0.174316] twl4030: PIH (irq 7) chaining IRQs 368..375 >>> [ 0.174560] twl4030: power (irq 373) chaining IRQs 376..383 >>> [ 0.177703] twl4030: gpio (irq 368) chaining IRQs 384..401 >>> [ 0.194580] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >>> standby >>> [ 0.198181] regulator: VDAC: 1800 mV normal standby >>> [ 0.201873] regulator: VDVI: 1800 mV normal standby >>> [ 0.205810] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >>> standby >>> [ 0.210021] regulator: VAUX3: 1800 mV normal standby >>> [ 0.213623] regulator: VAUX4: 1800 mV normal standby >>> [ 0.214294] omap_device: omap_i2c.1: new worst case deactivate >>> latency 0: 91552 >>> [ 0.214691] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >>> [ 0.229003] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >>> [ 0.239440] Advanced Linux Sound Architecture Driver Version 1.0.23. >>> [ 0.244750] Switching to clocksource 32k_counter >>> [ 0.435150] musb-hdrc: version 6.0, peripheral, debug=0 >>> [ 0.435577] musb-hdrc musb-hdrc.0: degrade from otg to >>> peripheral-only mode >>> [ 0.435668] musb-hdrc musb-hdrc.0: dma type: dma-inventra >>> [ 0.435699] HS USB OTG: no transceiver configured >>> [ 0.435729] musb-hdrc musb-hdrc.0: musb_init_controller failed with >>> status -19 >>> [ 0.437591] NET: Registered protocol family 2 >>> [ 0.438537] IP route cache hash table entries: 2048 (order: 1, 8192 >>> bytes) >>> [ 0.441192] TCP established hash table entries: 8192 (order: 4, 65536 >>> bytes) >>> [ 0.441772] TCP bind hash table entries: 8192 (order: 6, 360448 bytes) >>> [ 0.447326] TCP: Hash tables configured (established 8192 bind 8192) >>> [ 0.447509] TCP reno registered >>> [ 0.447540] UDP hash table entries: 128 (order: 1, 12288 bytes) >>> [ 0.448059] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) >>> [ 0.449432] NET: Registered protocol family 1 >>> [ 0.451385] RPC: Registered udp transport module. >>> [ 0.451416] RPC: Registered tcp transport module. >>> [ 0.451416] RPC: Registered tcp NFSv4.1 backchannel transport module. >>> [ 0.452758] NetWinder Floating Point Emulator V0.97 (double precision) >>> [ 0.456146] platform iva.0: Enabled OPP corresponding to 720MHz >>> [ 0.460144] omap-iommu omap-iommu.0: isp registered >>> [ 0.461303] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >>> [ 0.649597] VFS: Disk quotas dquot_6.5.2 >>> [ 0.649780] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >>> [ 0.653320] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, >>> Inc. >>> [ 0.657958] msgmni has been set to 474 >>> [ 0.663879] io scheduler noop registered >>> [ 0.663909] io scheduler deadline registered >>> [ 0.664184] io scheduler cfq registered (default) >>> [ 0.729553] OMAP DSS rev 2.0 >>> [ 0.730224] OMAP DISPC rev 3.0 >>> [ 0.730407] OMAP VENC rev 2 >>> [ 0.731964] OMAP DSI rev 1.0 >>> [ 1.061706] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >>> [ 1.074340] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >>> OMAP UART0 >>> [ 1.077087] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >>> OMAP UART1 >>> [ 1.079193] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >>> OMAP UART2 >>> [ 1.822540] console [ttyO2] enabled >>> [ 1.891143] brd: module loaded >>> [ 1.925689] loop: module loaded >>> [ 1.937622] mtdoops: mtd device (mtddev=name/number) must be supplied >>> [ 1.944610] omap2-nand driver initializing >>> [ 1.949676] ONFI flash detected >>> [ 1.953247] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron >>> ) >>> [ 1.960388] Creating 5 MTD partitions on "omap2-nand.0": >>> [ 1.966064] 0x000000000000-0x000000080000 : "X-Loader" >>> [ 1.984436] 0x000000080000-0x000000260000 : "U-Boot" >>> [ 1.999542] 0x000000260000-0x000000280000 : "U-Boot Env" >>> [ 2.014068] 0x000000280000-0x000000680000 : "Kernel" >>> [ 2.030242] 0x000000680000-0x000020000000 : "File System" >>> [ 2.301544] OneNAND driver initializing >>> [ 2.317413] mice: PS/2 mouse device common for all mice >>> [ 2.327362] input: gpio-keys as >>> /devices/platform/gpio-keys/input/input0 >>> [ 2.345733] omap_device: omap_i2c.1: new worst case activate latency >>> 0: 122070 >>> [ 2.355102] input: twl4030_pwrbutton as >>> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >>> [ 2.374267] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>> [ 2.381378] twl_rtc twl_rtc: Power up reset detected. >>> [ 2.387847] twl_rtc twl_rtc: Enabling TWL-RTC. >>> [ 2.395385] i2c /dev entries driver >>> [ 2.407806] Linux media interface: v0.10 >>> [ 2.413055] Linux video capture interface: v2.00 >>> [ 2.420562] omap3isp supply VDD_CSIPHY1 not found, using dummy >>> regulator >>> [ 2.427795] omap3isp supply VDD_CSIPHY2 not found, using dummy >>> regulator >>> [ 2.435546] omap3isp omap3isp: Revision 2.0 found >>> [ 2.440887] omap-iommu omap-iommu.0: isp: version 1.1 >>> [ 2.552551] omap_i2c omap_i2c.2: Arbitration lost >>> [ 2.573242] mt9v113 2-003c: chip id mismatch read 0x0, expecting >>> 0x2280 >>> [ 2.590240] isp_register_subdev_group: Unable to register subdev >>> mt9v113 >>> [ 2.598937] omap_device: omap_wdt.-1: new worst case activate latency >>> 0: 30517 >>> [ 2.609344] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>> [ 2.615814] omap_device: omap_wdt.-1: new worst case deactivate >>> latency 0: 30517 >>> [ 2.625457] twl4030_wdt twl4030_wdt: Failed to register misc device >>> [ 2.632202] twl4030_wdt: probe of twl4030_wdt failed with error -16 >>> [ 2.661651] usbcore: registered new interface driver usbhid >>> [ 2.667602] usbhid: USB HID core driver >>> [ 2.679443] ALSA device list: >>> [ 2.682678] No soundcards found. >>> [ 2.686248] oprofile: hardware counters not available >>> [ 2.691619] oprofile: using timer interrupt. >>> [ 2.696716] TCP cubic registered >>> [ 2.700225] Initializing XFRM netlink socket >>> [ 2.704986] NET: Registered protocol family 17 >>> [ 2.709930] NET: Registered protocol family 15 >>> [ 2.715393] Registering the dns_resolver key type >>> [ 2.721282] VFP support v0.3: implementor 41 architecture 3 part 30 >>> variant c rev 1 >>> [ 2.731414] ThumbEE CPU extension supported. >>> [ 2.758483] Power Management for TI OMAP3. >>> [ 2.763824] sr_init: No PMIC hook to init smartreflex >>> [ 2.769836] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >>> driver initialized >>> [ 2.779174] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >>> driver initialized >>> [ 2.789276] SmartReflex Class3 initialized >>> [ 2.857177] clock: disabling unused clocks to save power >>> [ 2.866088] platform iva.0: omap_voltage_scale: Already at the >>> requestedrate 360000000 >>> [ 2.874511] platform mpu.0: omap_voltage_scale: Already at the >>> requestedrate 500000000 >>> [ 2.882934] platform l3_main.0: omap_voltage_scale: Already at the >>> requestedrate 166000000 >>> [ 2.927032] regulator_init_complete: incomplete constraints, leaving >>> VDAC on >>> [ 2.938446] twl_rtc twl_rtc: setting system clock to 2000-01-01 >>> 00:00:00 UTC (946684800) >>> [ 2.947753] omap_vout omap_vout: Buffer Size = 3686400 >>> [ 2.957153] omap_vout omap_vout: : registered and initialized video >>> device 15 >>> [ 2.964782] omap_vout omap_vout: Buffer Size = 3686400 >>> [ 2.973541] omap_vout omap_vout: : registered and initialized video >>> device 16 >>> [ 2.988342] Waiting for root device /dev/mmcblk0p2... >>> [ 3.141418] mmc0: new high speed SDHC card at address aaaa >>> [ 3.151336] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >>> [ 3.175750] mmcblk0: p1 p2 >>> [ 3.218505] EXT3-fs: barriers not enabled >>> [ 3.227325] kjournald starting. Commit interval 5 seconds >>> [ 3.233612] EXT3-fs (mmcblk0p2): warning: maximal mount count >>> reached, running e2fsck is recommended >>> [ 3.247222] EXT3-fs (mmcblk0p2): using internal journal >>> [ 3.252807] EXT3-fs (mmcblk0p2): recovery complete >>> [ 3.258544] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data >>> mode >>> [ 3.266540] VFS: Mounted root (ext3 filesystem) on device 179:2. >>> [ 3.273132] Freeing init memory: 200K >>> Failed to open /dev/kmsg for logging: No such file or directory >>> [ 3.609405] <30>systemd[1]: systemd 37 running in system mode. (+PAM >>> +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >>> >>> Welcome to The ֵngstrצm Distribution! >>> >>> [ 3.713439] <28>systemd[1]: /sbin/modprobe failed with error code 1. >>> [ 3.724670] <30>systemd[1]: Set hostname to <beagleboard>. >>> Starting Runtime Directory... >>> Starting Remount API VFS... >>> Starting Lock Directory... >>> Starting Media Directory... >>> Started Apply Kernel Variables >>> [ OK ] >>> Started Huge Pages File System >>> [ OK ] >>> Starting POSIX Message Queue File System... >>> Starting File System Check on Root Device... >>> Started Load Kernel Modules >>> [ OK ] >>> Started Configuration File System >>> [ OK ] >>> Started FUSE Control File System >>> [ OK ] >>> Started Set Up Additional Binary Formats >>> [ OK ] >>> [ 4.677764] <30>systemd-fsck[593]: Root directory is writable, >>> skipping check. >>> Starting Debug File System... >>> Started Security File System >>> [ OK ] >>> Starting Syslog Kernel Log Buffer Bridge... >>> Started Syslog Kernel Log Buffer Bridge >>> [ OK ] >>> Starting udev Coldplug all Devices... >>> Starting udev Kernel Device Manager... >>> Started Runtime Directory >>> [ OK ] >>> Started Remount API VFS >>> [ OK ] >>> Started Lock Directory >>> [ OK ] >>> Started udev Ker[ 5.031005] <30>udevd[600]: starting version 175 >>> nel Device Manager [ OK ] >>> Started Media Directory >>> [ OK ] >>> Started POSIX Message Queue File System >>> [ OK ] >>> Started File System Check on Root Device >>> [ OK ] >>> Started Debug File System >>> [ OK ] >>> Starting Remount Root FS... >>> Starting STDOUT Syslog Bridge... >>> Started STDOUT Syslog Bridge >>> [ OK ] >>> Started Remount Root FS >>> [ OK ] >>> Started Opkg first boot configure >>> [ OK ] >>> Starting /tmp... >>> Started Machine ID first boot configure >>> [ OK ] >>> Started /tmp >>> [ OK ] >>> Starting Load Random Seed... >>> Starting Recreate Volatile Files and Directories... >>> Started Load Random Seed >>> [ OK ] >>> Started Recreate Volatile Files and Directories >>> [ OK ] >>> Starting Console System Startup Logging... >>> Starting xinetd.service... >>> Started Angstrom LED config >>> [ OK ] >>> Starting Timestamping service... >>> Started Timestamping service >>> [ OK ] >>> Starting Network Manager... >>> Started SSH Key Generation >>> [ OK ] >>> Starting System Logging Service... >>> Starting Permit User Sessions... >>> Starting Login Service... >>> Starting Avahi mDNS/DNS-SD Stack... >>> Starting Periodic Command Scheduler... >>> Started Periodic Command Scheduler >>> [ OK ] >>> Starting internet superserver: xinetdStarting D-Bus System Message Bus... >>> Starting Disk Manager... >>> Started Console System Startup Logging >>> [ OK ] >>> [ 8.354309] <27>systemd-logind[707]: Failed to open >>> /sys/class/tty/tty0/active: No such file or directory >>> Started Permit User Sessions >>> [ OK ] >>> [ 8.659515] <27>systemd-logind[707]: Failed to fully start up daemon: >>> No such file or directory >>> [ 8.877380] <29>systemd[1]: systemd-logind.service: main process >>> exited, code=exited, status=1 >>> [ 9.057952] <75>/usr/sbin/crond[722]: (CRON) INFO (Syslog will be >>> used instead of sendmail.): No such file or directory >>> . >>> Failed to start Login Service >>> [FAILED] >>> [ 9.415985] <30>avahi-daemon[711]: Found user 'avahi' (UID 998) and >>> group 'avahi' (GID 996). >>> [ 9.478942] <30>avahi-daemon[711]: Successfully dropped root >>> privileges. >>> See 'systemctl status systemd-logind.service' for details. >>> [ 9.517791] <29>systemd[1]: Unit systemd-logind.service entered >>> failed state. >>> [ 9.659942] <30>avahi-daemon[711]: avahi-daemon 0.6.30 starting up. >>> Started xinetd.service >>> [ OK ] >>> [ 9.930999] <26>xinetd[868]: 868 {init_services} no services. >>> Exiting... >>> Starting Serial Getty on ttyO2... >>> [ 10.786376] <30>NetworkManager[704]: NetworkManager[704]: <info> >>> NetworkManager (version 0.9.2.0) is starting... >>> Started Serial Getty on ttyO2 >>> [ OK ] >>> [ 11.033538] <30>udisks-daemon[770]: (process:770): GLib-WARNING **: >>> goption.c:2168: ignoring no-arg, optional-arg or filename flags (16) on >>> option of type 1 >>> [ 11.310058] <14>NetworkManager[704]: <info> NetworkManager (version >>> 0.9.2.0) is starting... >>> Started D-Bus System Message Bus >>> [ OK ] >>> [ 11.474243] <30>NetworkManager[704]: NetworkManager[704]: <info> Read >>> config file (null) >>> [ 11.721771] <14>NetworkManager[704]: <info> Read config file (null) >>> [ 11.728485] <30>load-timestamp.sh[702]: Update systemtime from >>> /etc/timestamp >>> [ 12.190551] <30>load-timestamp.sh[702]: Thu Jan 12 12:19:00 UTC 2012 >>> [ 12.656372] <27>systemd-uaccess[1031]: Failed to apply ACL on >>> /dev/v4l-subdev3: Operation not supported >>> [ 12.891265] <27>systemd-uaccess[1027]: Failed to apply ACL on >>> /dev/v4l-subdev0: Operation not supported >>> >>> .---O---. [ 13.117218] >>> <27>systemd-uaccess[1019]: Failed to apply ACL on /dev/v4l-subdev1: >>> Operation not supported >>> >>> | | .-. o o >>> | | |-----.-----.-[ 13.337951] <27>systemd-uaccess[1033]: Failed >>> to apply ACL on /dev/v4l-subdev2: Operation not supported >>> ----.| | .----..--[ 13.378295] <27>systemd-uaccess[1037]: Failed to >>> apply ACL on /dev/v4l-subdev6: Operation not supported >>> ---.-----. >>> | | | __ | ---'| '--.| .-'| | | >>> | | | | | |--- [ 13.526580] <27>systemd-uaccess[1040]: >>> Failed to apply ACL on /dev/v4l-subdev7: Operation not supported >>> || --'| | | ' | | | | >>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>> [ 13.677337] <27>systemd-uaccess[1028]: Failed to apply ACL on >>> /dev/v4l-subdev5: Operation not supported >>> -' | >>> '---' >>> >>> The Angstrom Distribution beagleboard ttyO2 >>> >>> Angstrom v2012.01-co[ 13.979644] <27>systemd-uaccess[1042]: Failed to >>> apply ACL on /dev/v4l-subdev4: Operation not supported >>> re - Kernel 2.6.37 >>> >>> beagleboard login: [ 14.332580] <27>systemd-uaccess[1049]: Failed to >>> apply ACL on /dev/video0: Operation not supported >>> [ 14.667114] <27>systemd-uaccess[1051]: Failed to apply ACL on >>> /dev/video1: Operation not supported >>> [ 14.995208] <27>systemd-uaccess[1053]: Failed to apply ACL on >>> /dev/video3: Operation not supported >>> Started udev Coldplug all Devices >>> [ OK ] >>> >>> [ 15.218170] <27>systemd-uaccess[1055]: Failed to apply ACL on >>> /dev/video2: Operation not supported >>> [ 15.450988] <27>systemd-uaccess[1057]: Failed to apply ACL on >>> /dev/video4: Operation not supported >>> Started Disk Manager >>> [ OK ] >>> >>> Started Avahi mDNS/DNS-SD Stack >>> [[ 15.689880] <27> OK ] >>> systemd-uaccess[1063]: Failed to apply ACL on >>> /dev/video5: Operation not supported >>> [ 15.800720] <27>systemd-uaccess[1073]: Failed to apply ACL on >>> /dev/video8: Operation not supported >>> [ 16.030517] <27>systemd-uaccess[1072]: Failed to apply ACL on >>> /dev/video7: Operation not supported >>> [ 16.091583] <27>systemd-uaccess[1086]: Failed to apply ACL on >>> /dev/video6: Operation not supported >>> Stopping Syslog Kernel Log Buffer Bridge... >>> [ 16.201354] >>> <30>udisks-daemon[770]: (udisks-daemon:770): udisks-daemon-DEBUG: Starting >>> daemon version 1.0.4 >>> [ 16.326660] <30>avahi-daemon[711]: Successfully called chroot(). >>> [ 16.400512] <30>avahi-daemon[711]: Successfully dropped remaining >>> capabilities. >>> [ 16.473449] <30>avahi-daemon[711]: Loading service file >>> /services/sftp-ssh.service. >>> [ 16.510803] <30>avahi-daemon[711]: Loading service file >>> /services/ssh.service. >>> [ 16.565338] <30>avahi-daemon[711]: Loading service file >>> /services/udisks.service. >>> [ 16.644561] <30>avahi-daemon[711]: Network interface enumeration >>> completed. >>> [ 16.669464] <30>avahi-daemon[711]: Registering HINFO record with >>> values 'ARMV7L'/'LINUX'. >>> [ 16.757904] <30>avahi-daemon[711]: Server startup complete. Host name >>> is beagleboard.local. Local service cookie is 441939348. >>> Starting Getty on tty1... >>> [ 16.862426] <30>avahi-daemon[711]: Service >>> "beagleboard" (/services/udisks.service) successfully established. >>> [ 16.971832] <30>dbus-daemon[969]: dbus[969]: [system] Activating >>> service name='org.freedesktop.PolicyKit1' (using servicehelper) >>> Started Getty on tty1 >>> [ OK ] >>> >>> [ 17.104522] <29>dbus[969]: [system] Activating service >>> name='org.freedesktop.PolicyKit1' (using servicehelper) >>> [ 17.218292] <30>avahi-daemon[711]: Service "beagleboard" >>> (/services/ssh.service) successfully established. >>> Starting Gnome D[ 17.271667] <27>isplay Manager..systemd-uaccess. >>> >>> [1199]: Failed to apply ACL on /dev/snd/timer: Operation not supported >>> [ 17.293273] <30>avahi-daemon[711]: Service "beagleboard" >>> (/services/sftp-ssh.service) successfully established. >>> Started Gnome Display Manager >>> [ OK ] >>> >>> Stopped Syslog Kernel Log Buffer Bridge >>> [ OK ] >>> >>> Started System Logging Service >>> [ OK ] >>> >>> Started Network Manager >>> [ OK ] >>> >>> .---O---. >>> | | .-. o o >>> | | |-----.-----.-----.| | .----..-----.-----. >>> | | | __ | ---'| '--.| .-'| | | >>> | | | | | |--- || --'| | | ' | | | | >>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>> -' | >>> '---' >>> >>> The Angstrom Distribution beagleboard ttyO2 >>> >>> Angstrom v2012.01-core - Kernel 2.6.37 >>> >>> beagleboard login: >>> .---O---. >>> | | .-. o o >>> | | |-----.-----.-----.| | .----..-----.-----. >>> | | | __ | ---'| '--.| .-'| | | >>> | | | | | |--- || --'| | | ' | | | | >>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-' >>> -' | >>> '---' >>> >>> The Angstrom Distribution beagleboard ttyO2 >>> >>> Angstrom v2012.01-core - Kernel 2.6.37 >>> >>> beagleboard login: root >>> Last login: Thu Jan 12 12:19:48 GMT 2012 on ttyO2 >>> root@beagleboard:~# >>> root@beagleboard:~# >>> root@beagleboard:~# cd /lib/modules/2.6.37/kernel/drivers/usb/gadget/ >>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget# insmod >>> g_ether.ko >>> insmod: error inserting 'g_ether.ko': -1 No such device >>> root@beagleboard:/lib/modules/2.6.37/kernel/drivers/usb/gadget >>> >>> Regards, >>> Ran >>> >>> >>> On Thu, Jan 15, 2015 at 6:26 PM, Robert Nelson <[email protected]> >>> wrote: >>> >>>> On Thu, Jan 15, 2015 at 10:23 AM, Ran Shalit <[email protected]> >>>> wrote: >>>> > Hi Robert, >>>> > >>>> > Thank you very much. >>>> > I was lazy not to notice that.... >>>> > It now seems better (less errors on boot), but still fails with same >>>> error: >>>> > insmod: error inserting 'g_ether.ko': -1 No such device >>>> > Can you give me another hint what might cause such failure? >>>> > >>>> > This is the boot log: >>>> > >>>> > Last login: Thu Jan 12 12:31:58 GMT 2012 on ttyO2 >>>> > root@beagleboard:~# >>>> > root@beagleboard:~# >>>> > root@beagleboard:~# >>>> > root@beagleboard:~# modprobe g_ether >>>> > [ 30.667053] g_ether: disagrees about version of symbol >>>> module_layout >>>> > FATAL: Error inserting g_ether >>>> >>>> This means your kernel was built seperatly from the modules.. >>>> >>>> When you build your kernel, just also build 'make modules' and install >>>> them to the rootfs.. >>>> >>>> >>>> > (/lib/modules/2.6.37/kernel/drivers/usb/gadget/g_ether.ko): Invalid >>>> module >>>> > format >>>> > root@beagleboard:~# d >>>> > >>>> > Texas Instruments X-Loader 1.5.0 (Jun 14 2011 - 22:04:07) >>>> > Beagle Rev C5 >>>> > Reading boot sector >>>> > Loading u-boot.bin from mmc >>>> > >>>> > >>>> > U-Boot 2009.06-rc2 (Jan 15 2015 - 11:12:37) >>>> > >>>> > , CPU-OPP2 L3-165MHz >>>> > OMAP3 Beagle board + LPDDR/NAND >>>> > DRAM: 256 MB >>>> > NAND: 512 MiB >>>> > In: serial >>>> > Out: serial >>>> > Err: serial >>>> > Board revision Ax/Bx >>>> > Die ID #74aa000700000000015a676401014023 >>>> > Hit any key to stop autoboot: 0 >>>> > mmc1 is available >>>> > reading uImage >>>> > >>>> > 2918324 bytes read >>>> > ## Booting kernel from Legacy Image at 80300000 ... >>>> > Image Name: Linux-2.6.37 >>>> > Image Type: ARM Linux Kernel Image (uncompressed) >>>> > Data Size: 2918260 Bytes = 2.8 MB >>>> > Load Address: 80008000 >>>> > Entry Point: 80008000 >>>> > Verifying Checksum ... OK >>>> > Loading Kernel Image ... OK >>>> > OK >>>> > >>>> > Starting kernel ... >>>> > >>>> > Uncompressing Linux... done, booting the kernel. >>>> > [ 0.000000] Linux version 2.6.37 (ubuntu@ubuntu-laptop) (gcc >>>> version >>>> > 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #7 Thu Jan 15 18:09:40 IST 2015 >>>> > [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), >>>> > cr=10c53c7f >>>> > [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing >>>> > instruction cache >>>> > [ 0.000000] Machine: OMAP3 Beagle Board >>>> > [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM >>>> > [ 0.000000] Memory policy: ECC disabled, Data cache writeback >>>> > [ 0.000000] OMAP3430/3530 ES3.1.2 (l2cache iva sgx neon isp 720mhz >>>> ) >>>> > [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: >>>> 0x10000 >>>> > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping >>>> on. Total >>>> > pages: 64000 >>>> > [ 0.000000] Kernel command line: console=ttyO2,115200n8 >>>> > root=/dev/mmcblk0p2 rw rootwait >>>> > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) >>>> > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, >>>> 131072 >>>> > bytes) >>>> > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 >>>> bytes) >>>> > [ 0.000000] Memory: 252MB = 252MB total >>>> > [ 0.000000] Memory: 242740k/242740k available, 19404k reserved, 0K >>>> > highmem >>>> > [ 0.000000] Virtual kernel memory layout: >>>> > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) >>>> > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) >>>> > [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) >>>> > [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) >>>> > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) >>>> > [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) >>>> > [ 0.000000] .init : 0xc0008000 - 0xc003a000 ( 200 kB) >>>> > [ 0.000000] .text : 0xc003a000 - 0xc0568f4c (5308 kB) >>>> > [ 0.000000] .data : 0xc056a000 - 0xc071f1a0 (1749 kB) >>>> > [ 0.000000] NR_IRQS:409 >>>> > [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>>> > [ 0.000000] omap_hwmod: i2c1: softreset failed (waited 10000 usec) >>>> > [ 0.000000] omap_hwmod: i2c2: softreset failed (waited 10000 usec) >>>> > [ 0.000000] omap_hwmod: i2c3: softreset failed (waited 10000 usec) >>>> > [ 0.000000] Reprogramming SDRC clock to 332000000 Hz >>>> > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 >>>> > interrupts >>>> > [ 0.000000] Total of 96 interrupts on 1 active controller >>>> > [ 0.000000] GPMC revision 5.0 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ402 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ403 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ404 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ405 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ406 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ407 >>>> > [ 0.000000] Trying to install interrupt handler for IRQ408 >>>> > [ 0.000000] Trying to install type control for IRQ409 >>>> > [ 0.000000] Trying to set irq flags for IRQ409 >>>> > [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz >>>> > [ 0.000000] Console: colour dummy device 80x30 >>>> > [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, >>>> Inc., >>>> > Ingo Molnar >>>> > [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 >>>> > [ 0.000000] ... MAX_LOCK_DEPTH: 48 >>>> > [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 >>>> > [ 0.000000] ... CLASSHASH_SIZE: 4096 >>>> > [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 >>>> > [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 >>>> > [ 0.000000] ... CHAINHASH_SIZE: 16384 >>>> > [ 0.000000] memory used by lock dependency info: 3951 kB >>>> > [ 0.000000] per task-struct memory footprint: 2304 bytes >>>> > [ 0.000000] Calibrating delay loop... 456.86 BogoMIPS (lpj=1781760) >>>> > [ 0.000000] pid_max: default: 32768 minimum: 301 >>>> > [ 0.000000] Security Framework initialized >>>> > [ 0.000000] Mount-cache hash table entries: 512 >>>> > [ 0.000000] CPU: Testing write buffer coherency: ok >>>> > [ 0.000000] devtmpfs: initialized >>>> > [ 0.000000] regulator: core version 0.5 >>>> > [ 0.000000] regulator: dummy: >>>> > [ 0.000000] NET: Registered protocol family 16 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] OMAP GPIO hardware version 2.5 >>>> > [ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0 >>>> > [ 0.000000] OMAP3 Beagle Rev: C4 >>>> > [ 0.000000] Found NAND on CS0 >>>> > [ 0.000000] Registering NAND on CS0 >>>> > [ 0.000000] Unable to get DVI reset GPIO >>>> > [ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported. >>>> > [ 0.000000] OMAP DMA hardware revision 4.0 >>>> > [ 0.122314] bio: create slab <bio-0> at 0 >>>> > [ 0.133697] SCSI subsystem initialized >>>> > [ 0.147491] usbcore: registered new interface driver usbfs >>>> > [ 0.149322] usbcore: registered new interface driver hub >>>> > [ 0.150878] usbcore: registered new device driver usb >>>> > [ 0.157501] omap_device: omap_i2c.1: new worst case activate >>>> latency 0: >>>> > 30517 >>>> > [ 0.157684] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz >>>> > [ 0.172485] twl4030: PIH (irq 7) chaining IRQs 368..375 >>>> > [ 0.172729] twl4030: power (irq 373) chaining IRQs 376..383 >>>> > [ 0.175842] twl4030: gpio (irq 368) chaining IRQs 384..401 >>>> > [ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal >>>> standby >>>> > [ 0.196044] regulator: VDAC: 1800 mV normal standby >>>> > [ 0.199615] regulator: VDVI: 1800 mV normal standby >>>> > [ 0.203613] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal >>>> standby >>>> > [ 0.207763] regulator: VAUX3: 1800 mV normal standby >>>> > [ 0.211334] regulator: VAUX4: 1800 mV normal standby >>>> > [ 0.211914] omap_device: omap_i2c.1: new worst case deactivate >>>> latency 0: >>>> > 61035 >>>> > [ 0.221954] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz >>>> > [ 0.236083] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz >>>> > [ 0.246398] Advanced Linux Sound Architecture Driver Version >>>> 1.0.23. >>>> > [ 0.251586] Switching to clocksource 32k_counter >>>> > [ 0.440246] musb-hdrc: version 6.0, peripheral, debug=0 >>>> > [ 0.440673] musb-hdrc musb-hdrc.0: degrade from otg to >>>> peripheral-only >>>> > mode >>>> > [ 0.440795] musb-hdrc musb-hdrc.0: dma type: dma-inventra >>>> > [ 0.440826] HS USB OTG: no transceiver configured >>>> > [ 0.440856] musb-hdrc musb-hdrc.0: musb_init_controller failed with >>>> > status -19 >>>> > [ 0.442718] NET: Registered protocol family 2 >>>> > [ 0.443664] IP route cache hash table entries: 2048 (order: 1, 8192 >>>> > bytes) >>>> > [ 0.446136] TCP established hash table entries: 8192 (order: 4, >>>> 65536 >>>> > bytes) >>>> > [ 0.446746] TCP bind hash table entries: 8192 (order: 6, 360448 >>>> bytes) >>>> > [ 0.452423] TCP: Hash tables configured (established 8192 bind >>>> 8192) >>>> > [ 0.452545] TCP reno registered >>>> > [ 0.452606] UDP hash table entries: 128 (order: 1, 12288 bytes) >>>> > [ 0.453033] UDP-Lite hash table entries: 128 (order: 1, 12288 >>>> bytes) >>>> > [ 0.454437] NET: Registered protocol family 1 >>>> > [ 0.456481] RPC: Registered udp transport module. >>>> > [ 0.456512] RPC: Registered tcp transport module. >>>> > [ 0.456542] RPC: Registered tcp NFSv4.1 backchannel transport >>>> module. >>>> > [ 0.457855] NetWinder Floating Point Emulator V0.97 (double >>>> precision) >>>> > [ 0.461059] platform iva.0: Enabled OPP corresponding to 720MHz >>>> > [ 0.465179] omap-iommu omap-iommu.0: isp registered >>>> > [ 0.466308] OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) >>>> > [ 0.654205] VFS: Disk quotas dquot_6.5.2 >>>> > [ 0.654388] Dquot-cache hash table entries: 1024 (order 0, 4096 >>>> bytes) >>>> > [ 0.657714] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red >>>> Hat, >>>> > Inc. >>>> > [ 0.659271] msgmni has been set to 474 >>>> > [ 0.665100] io scheduler noop registered >>>> > [ 0.665191] io scheduler deadline registered >>>> > [ 0.665435] io scheduler cfq registered (default) >>>> > [ 0.728576] OMAP DSS rev 2.0 >>>> > [ 0.729248] OMAP DISPC rev 3.0 >>>> > [ 0.729431] OMAP VENC rev 2 >>>> > [ 0.730957] OMAP DSI rev 1.0 >>>> > [ 1.060791] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >>>> > [ 1.073242] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a >>>> OMAP >>>> > UART0 >>>> > [ 1.076141] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a >>>> OMAP >>>> > UART1 >>>> > [ 1.078155] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a >>>> OMAP >>>> > UART2 >>>> > [ 1.821472] console [ttyO2] enabled >>>> > [ 1.889343] brd: module loaded >>>> > [ 1.923370] loop: module loaded >>>> > [ 1.935363] mtdoops: mtd device (mtddev=name/number) must be >>>> supplied >>>> > [ 1.942352] omap2-nand driver initializing >>>> > [ 1.947479] ONFI flash detected >>>> > [ 1.951019] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc >>>> (Micron ) >>>> > [ 1.958160] Creating 5 MTD partitions on "omap2-nand.0": >>>> > [ 1.963836] 0x000000000000-0x000000080000 : "X-Loader" >>>> > [ 1.982055] 0x000000080000-0x000000260000 : "U-Boot" >>>> > [ 1.997100] 0x000000260000-0x000000280000 : "U-Boot Env" >>>> > [ 2.011535] 0x000000280000-0x000000680000 : "Kernel" >>>> > [ 2.027618] 0x000000680000-0x000020000000 : "File System" >>>> > [ 2.298248] OneNAND driver initializing >>>> > [ 2.315246] mice: PS/2 mouse device common for all mice >>>> > [ 2.324920] input: gpio-keys as >>>> /devices/platform/gpio-keys/input/input0 >>>> > [ 2.343780] omap_device: omap_i2c.1: new worst case activate >>>> latency 0: >>>> > 91552 >>>> > [ 2.352966] input: twl4030_pwrbutton as >>>> > >>>> /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 >>>> > [ 2.372009] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>>> > [ 2.379119] twl_rtc twl_rtc: Power up reset detected. >>>> > [ 2.385589] twl_rtc twl_rtc: Enabling TWL-RTC. >>>> > [ 2.393066] i2c /dev entries driver >>>> > [ 2.405456] Linux media interface: v0.10 >>>> > [ 2.410736] Linux video capture interface: v2.00 >>>> > [ 2.418273] omap3isp supply VDD_CSIPHY1 not found, using dummy >>>> regulator >>>> > [ 2.425506] omap3isp supply VDD_CSIPHY2 not found, using dummy >>>> regulator >>>> > [ 2.433227] omap3isp omap3isp: Revision 2.0 found >>>> > [ 2.438476] omap-iommu omap-iommu.0: isp: version 1.1 >>>> > [ 2.559204] omap_i2c omap_i2c.2: Arbitration lost >>>> > [ 2.580078] mt9v113 2-003c: chip id mismatch read 0x0, expecting >>>> 0x2280 >>>> > [ 2.597198] isp_register_subdev_group: Unable to register subdev >>>> mt9v113 >>>> > [ 2.605865] omap_device: omap_wdt.-1: new worst case activate >>>> latency 0: >>>> > 30517 >>>> > [ 2.616241] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>>> > [ 2.622711] omap_device: omap_wdt.-1: new worst case deactivate >>>> latency >>>> > 0: 30517 >>>> > [ 2.632354] twl4030_wdt twl4030_wdt: Failed to register misc device >>>> > [ 2.639099] twl4030_wdt: probe of twl4030_wdt failed with error -16 >>>> > [ 2.668334] usbcore: registered new interface driver usbhid >>>> > [ 2.674285] usbhid: USB HID core driver >>>> > [ 2.686126] ALSA device list: >>>> > [ 2.689392] No soundcards found. >>>> > [ 2.692962] oprofile: hardware counters not available >>>> > [ 2.698333] oprofile: using timer interrupt. >>>> > [ 2.703430] TCP cubic registered >>>> > [ 2.706939] Initializing XFRM netlink socket >>>> > [ 2.711639] NET: Registered protocol family 17 >>>> > [ 2.716613] NET: Registered protocol family 15 >>>> > [ 2.722045] Registering the dns_resolver key type >>>> > [ 2.727783] VFP support v0.3: implementor 41 architecture 3 part 30 >>>> > variant c rev 1 >>>> > [ 2.737945] ThumbEE CPU extension supported. >>>> > [ 2.764984] Power Management for TI OMAP3. >>>> > [ 2.770355] sr_init: No PMIC hook to init smartreflex >>>> > [ 2.776336] smartreflex smartreflex.0: omap_sr_probe: SmartReflex >>>> driver >>>> > initialized >>>> > [ 2.785644] smartreflex smartreflex.1: omap_sr_probe: SmartReflex >>>> driver >>>> > initialized >>>> > [ 2.795776] SmartReflex Class3 initialized >>>> > [ 2.863677] clock: disabling unused clocks to save power >>>> > [ 2.872497] platform iva.0: omap_voltage_scale: Already at the >>>> > requestedrate 360000000 >>>> > [ 2.880920] platform mpu.0: omap_voltage_scale: Already at the >>>> > requestedrate 500000000 >>>> > [ 2.889343] platform l3_main.0: omap_voltage_scale: Already at the >>>> > requestedrate 166000000 >>>> > [ 2.931488] omap_device: omap_i2c.1: new worst case deactivate >>>> latency 0: >>>> > 122070 >>>> > [ 2.940246] regulator_init_complete: incomplete constraints, >>>> leaving VDAC >>>> > on >>>> > [ 2.952911] twl_rtc twl_rtc: setting system clock to 2000-01-01 >>>> 00:00:00 >>>> > UTC (946684800) >>>> > [ 2.962005] omap_vout omap_vout: Buffer Size = 3686400 >>>> > [ 2.971313] omap_vout omap_vout: : registered and initialized video >>>> > device 15 >>>> > [ 2.978973] omap_vout omap_vout: Buffer Size = 3686400 >>>> > [ 2.987640] omap_vout omap_vout: : registered and initialized video >>>> > device 16 >>>> > [ 3.002319] Waiting for root device /dev/mmcblk0p2... >>>> > [ 3.166046] mmc0: new high speed SDHC card at address aaaa >>>> > [ 3.175537] mmcblk0: mmc0:aaaa SU16G 14.8 GiB >>>> > [ 3.200164] mmcblk0: p1 p2 >>>> > [ 3.232910] EXT3-fs: barriers not enabled >>>> > [ 3.312805] kjournald starting. Commit interval 5 seconds >>>> > [ 3.319183] EXT3-fs (mmcblk0p2): warning: maximal mount count >>>> reached, >>>> > running e2fsck is recommended >>>> > [ 3.333465] EXT3-fs (mmcblk0p2): using internal journal >>>> > [ 3.339080] EXT3-fs (mmcblk0p2): recovery complete >>>> > [ 3.347442] EXT3-fs (mmcblk0p2): mounted filesystem with ordered >>>> data >>>> > mode >>>> > [ 3.355468] VFS: Mounted root (ext3 filesystem) on device 179:2. >>>> > [ 3.362091] Freeing init memory: 200K >>>> > Failed to open /dev/kmsg for logging: No such file or directory >>>> > [ 3.685821] <30>systemd[1]: systemd 37 running in system mode. >>>> (+PAM >>>> > +LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom) >>>> > >>>> > Welcome to The ֵngstrצm Distribution! >>>> > >>>> > [ 3.784942] <28>systemd[1]: /sbin/modprobe failed with error code >>>> 1. >>>> > [ 3.796173] <30>systemd[1]: Set hostname to <beagleboard>. >>>> > [ 4.271270] <27>systemd[1]: Failed to open /dev/autofs: No such >>>> file or >>>> > directory >>>> >>>> add: CONFIG_AUTOFS4_FS=y >>>> >>>> Regards, >>>> >>>> -- >>>> Robert Nelson >>>> http://www.rcn-ee.com/ >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to a topic in the >>>> Google Groups "BeagleBoard" group. >>>> To unsubscribe from this topic, visit >>>> https://groups.google.com/d/topic/beagleboard/RznTdyaz2gg/unsubscribe. >>>> To unsubscribe from this group and all its topics, send an email to >>>> [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
