> > *It seems to me that usb0 isn't getting an ip address(192.168.7.2) > correctly?* > *Any suggestions?* >
Woah nelly ! That's a lot of output, ;) So, I'm not all that familiar with the Jessie images, but it seems as though the cdc_ether device is working fine. Have you attempted manually bring up eth1 ? e.g. sudo ifconfig eth1 192.168.7.2 sudo ifconfig eth1 up ?? But even then I'm not sure what could be the cause for eth1 not coming up, other than a couple guesses. I might have to defer to Robert, as he honestly knows these images better than all. On Thu, Mar 10, 2016 at 8:19 PM, Cornelius Lee <[email protected]> wrote: > Hi William, > > Thank you for your email,...below is what I get from running that command. > > cornelius@cornelius ~ $ dmesg|grep eth > [ 0.988379] e1000e 0000:00:19.0 eth0: registered PHC clock > [ 0.988382] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) > ec:f4:bb:0f:df:a3 > [ 0.988383] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network > Connection > [ 0.988419] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: > FFFFFF-0FF > [ 4.860468] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 7.445242] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow > Control: None > [ 7.445246] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO > [ 7.445274] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 2935.339583] usbcore: registered new interface driver cdc_ether > [ 2935.341774] rndis_host 1-2:1.0 eth1: register 'rndis_host' at > usb-0000:00:14.0-2, RNDIS device, a0:f6:fd:4b:fd:c9 > [ 3005.699765] NETDEV WATCHDOG: eth1 (rndis_host): transmit queue 0 timed > out > [ 3005.699766] Modules linked in: rndis_wlan rndis_host cdc_ether usbnet > mii cdc_acm nls_iso8859_1 uas usb_storage xt_multiport iptable_filter > ip_tables x_tables pci_stub vboxpci(OE) vboxnetadp(OE) vboxnetflt(OE) > vboxdrv(OE) pn544_mei mei_phy pn544 hci nfc dell_wmi sparse_keymap uvcvideo > videobuf2_vmalloc videobuf2_memops videobuf2_core v4l2_common videodev > media hid_logitech_hidpp snd_usb_audio snd_usbmidi_lib dell_laptop dcdbas > i8k dm_multipath scsi_dh intel_rapl iosf_mbi x86_pkg_temp_thermal > intel_powerclamp coretemp kvm_intel arc4 kvm bnep snd_hda_codec_hdmi > crct10dif_pclmul rfcomm crc32_pclmul ghash_clmulni_intel > snd_hda_codec_realtek snd_hda_codec_generic snd_soc_rt5640 iwlmvm bluetooth > snd_soc_rl6231 mac80211 aesni_intel snd_soc_core aes_x86_64 lrw gf128mul > snd_compress glue_helper ablk_helper snd_pcm_dmaengine cryptd snd_hda_intel > snd_hda_controller snd_seq_midi snd_hda_codec snd_seq_midi_event snd_hwdep > snd_rawmidi iwlwifi snd_pcm joydev serio_raw cfg80211 lpc_ich shpchp mei_me > mei 8250_fintek dw_dmac dell_smo8800 dw_dmac_core snd_seq snd_seq_device > snd_soc_sst_acpi snd_timer snd i2c_hid 8250_dw spi_pxa2xx_platform > i2c_designware_platform i2c_designware_core binfmt_misc dell_rbtn mac_hid > soundcore parport_pc ppdev lp parport dm_mirror dm_region_hash dm_log > hid_generic hid_logitech_dj usbhid hid i915 psmouse ahci i2c_algo_bit > libahci sdhci_pci drm_kms_helper e1000e drm ptp pps_core wmi video > sdhci_acpi sdhci > [ 3361.518375] rndis_host 1-2:1.0 eth1: unregister 'rndis_host' > usb-0000:00:14.0-2, RNDIS device > [ 3395.837660] rndis_host 1-2:1.0 eth1: register 'rndis_host' at > usb-0000:00:14.0-2, RNDIS device, a0:f6:fd:4b:fd:c9 > > > and running dmesg|grep usb gives me the following,... > > [ 2935.309616] usb 1-2: Product: BeagleBoneBlack > [ 2935.309617] usb 1-2: Manufacturer: Circuitco > [ 2935.309618] usb 1-2: SerialNumber: 5315BBBK0EEE > [ 2935.311093] usb-storage 1-2:1.4: USB Mass Storage device detected > [ 2935.311147] scsi host5: usb-storage 1-2:1.4 > [ 2935.332057] usbcore: registered new interface driver cdc_acm > [ 2935.339583] usbcore: registered new interface driver cdc_ether > [ 2935.341774] rndis_host 1-2:1.0 eth1: register 'rndis_host' at > usb-0000:00:14.0-2, RNDIS device, a0:f6:fd:4b:fd:c9 > [ 2935.341859] usbcore: registered new interface driver rndis_host > [ 2935.344118] usbcore: registered new interface driver rndis_wlan > [ 3005.699766] Modules linked in: rndis_wlan rndis_host cdc_ether usbnet > mii cdc_acm nls_iso8859_1 uas usb_storage xt_multiport iptable_filter > ip_tables x_tables pci_stub vboxpci(OE) vboxnetadp(OE) vboxnetflt(OE) > vboxdrv(OE) pn544_mei mei_phy pn544 hci nfc dell_wmi sparse_keymap uvcvideo > videobuf2_vmalloc videobuf2_memops videobuf2_core v4l2_common videodev > media hid_logitech_hidpp snd_usb_audio snd_usbmidi_lib dell_laptop dcdbas > i8k dm_multipath scsi_dh intel_rapl iosf_mbi x86_pkg_temp_thermal > intel_powerclamp coretemp kvm_intel arc4 kvm bnep snd_hda_codec_hdmi > crct10dif_pclmul rfcomm crc32_pclmul ghash_clmulni_intel > snd_hda_codec_realtek snd_hda_codec_generic snd_soc_rt5640 iwlmvm bluetooth > snd_soc_rl6231 mac80211 aesni_intel snd_soc_core aes_x86_64 lrw gf128mul > snd_compress glue_helper ablk_helper snd_pcm_dmaengine cryptd snd_hda_intel > snd_hda_controller snd_seq_midi snd_hda_codec snd_seq_midi_event snd_hwdep > snd_rawmidi iwlwifi snd_pcm joydev serio_raw cfg80211 lpc_ich shpchp mei_me > mei 8250_fintek dw_dmac dell_smo8800 dw_dmac_core snd_seq snd_seq_device > snd_soc_sst_acpi snd_timer snd i2c_hid 8250_dw spi_pxa2xx_platform > i2c_designware_platform i2c_designware_core binfmt_misc dell_rbtn mac_hid > soundcore parport_pc ppdev lp parport dm_mirror dm_region_hash dm_log > hid_generic hid_logitech_dj usbhid hid i915 psmouse ahci i2c_algo_bit > libahci sdhci_pci drm_kms_helper e1000e drm ptp pps_core wmi video > sdhci_acpi sdhci > [ 3361.518323] usb 1-2: USB disconnect, device number 5 > [ 3361.518375] rndis_host 1-2:1.0 eth1: unregister 'rndis_host' > usb-0000:00:14.0-2, RNDIS device > [ 3395.707524] usb 1-2: new high-speed USB device number 6 using xhci_hcd > [ 3395.835858] usb 1-2: New USB device found, idVendor=1d6b, idProduct=0104 > [ 3395.835863] usb 1-2: New USB device strings: Mfr=3, Product=4, > SerialNumber=5 > [ 3395.835865] usb 1-2: Product: BeagleBoneBlack > [ 3395.835867] usb 1-2: Manufacturer: Circuitco > [ 3395.835869] usb 1-2: SerialNumber: 5315BBBK0EEE > [ 3395.837660] rndis_host 1-2:1.0 eth1: register 'rndis_host' at > usb-0000:00:14.0-2, RNDIS device, a0:f6:fd:4b:fd:c9 > [ 3395.838325] usb-storage 1-2:1.4: USB Mass Storage device detected > [ 3395.838386] scsi host6: usb-storage 1-2:1.4 > > > It seems to me that usb0 isn't getting an ip address(192.168.7.2) > correctly? > Any suggestions? > > Regards, > Cornelius > > > > On Fri, Mar 11, 2016 at 11:00 AM, William Hermans <[email protected]> > wrote: > >> Perhaps running dmesg will give you a better idea of what's going on. If >> nothing else it'll give you some output to post here for others to have a >> better idea of whats going on. >> >> *example* >> >> william@beaglebone:~$ dmesg | grep eth >> [ 4.483906] cpsw 4a100000.ethernet: Detected MACID = 78:a5:04:ca:fb:dc >> [ 12.770249] net eth0: initializing cpsw version 1.12 (0) >> [ 12.780876] net eth0: phy found : id is : 0x7c0f1 >> [ 12.795971] net eth0: phy 4a101000.mdio:03 not found on slave 1 >> [ 12.806243] net eth0: BQL enabled >> [ 14.773478] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - >> flow control rx/tx >> [563836.873858] cpsw 4a100000.ethernet eth0: Link is Down >> [563838.954250] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - >> flow control rx/tx >> [566399.033841] cpsw 4a100000.ethernet eth0: Link is Down >> [566401.114229] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - >> flow control rx/tx >> >> >> On Thu, Mar 10, 2016 at 7:56 PM, Cornelius Lee <[email protected]> >> wrote: >> >>> Hi Robert, >>> >>> I have just flashed >>> https://rcn-ee.com/rootfs/bb.org/testing/2016-03-09/lxqt-4gb/BBB-eMMC-flasher-debian-8.3-lxqt-4gb-armhf-2016-03-09-4gb.img.xz >>> >>> and i can't ping to 192.168.7.2. Furthermore, ifconfig pulls up no inet >>> address on eth1. >>> >>> Any idea why? >>> >>> >>> Regards, >>> Cornelius >>> >>> >>> >>> On Thu, Mar 10, 2016 at 11:56 PM, Robert Nelson <[email protected] >>> > wrote: >>> >>>> On Thu, Mar 10, 2016 at 9:50 AM, Cornelius Lee <[email protected]> >>>> wrote: >>>> > Ah, great! Thank you. >>>> > I will test it tomorrow in the morning at the office then. >>>> > I will keep you updated too. =) >>>> > >>>> > Goodnight from Singapore. >>>> >>>> BTW, I'm not sure how to reverse connman's direction: >>>> >>>> But right now, when you plug in the usb connector, your laptop/desktop >>>> will get an ip (192.168.7.x) and use the bbb for internet over your >>>> laptop/desktop's wifi/ethernet.. So if you plug in an ethernet cable >>>> into the bbb, you'll get network access again on your laptop/desktop.. >>>> >>>> Trying to figure out how to reverse that. ;) >>>> >>>> Regards, >>>> >>>> >>>> -- >>>> Robert Nelson >>>> https://rcn-ee.com/ >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to a topic in the >>>> Google Groups "BeagleBoard" group. >>>> To unsubscribe from this topic, visit >>>> https://groups.google.com/d/topic/beagleboard/cvW0j4knXe4/unsubscribe. >>>> To unsubscribe from this group and all its topics, send an email to >>>> [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to a topic in the >> Google Groups "BeagleBoard" group. >> To unsubscribe from this topic, visit >> https://groups.google.com/d/topic/beagleboard/cvW0j4knXe4/unsubscribe. >> To unsubscribe from this group and all its topics, send an email to >> [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
