On Tue, Sep 20, 2016 at 12:17 PM, Robert Nelson <robertcnel...@gmail.com> wrote: > On Tue, Sep 20, 2016 at 12:05 PM, Dave Lynch <dhlyn...@gmail.com> wrote: >> That image is not working for me either. >> >> If I am following this, there is an issue where the eMMC is being >> partitioned as if it is 4G instead of 2G correct ? >> >> If I just modify the sfdisk portion of the Flash script will that correct >> this ? >> > > Humm.. > > i had just tested > BBB-eMMC-flasher-debian-8.5-console-armhf-2016-09-09-2gb.img.xz this > morning on a Rev C.. (it had flashed just fine) > > Let's try it on one of my old A5A's.. (that's close to your A6)..
So on my A5A... U-Boot SPL 2016.09-rc2-00001-g2e7c9a7 (Sep 09 2016 - 14:20:16) Trying to boot from MMC2 Expected Linux image is not found. Trying to start U-boot U-Boot 2016.09-rc2-00001-g2e7c9a7 (Sep 09 2016 - 14:20:16 -0500), Build: jenkins-github_Bootloader-Builder-446 DRAM: 512 MiB Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Board: BeagleBone Black Net: Warning: ethernet@4a100000 using MAC address from ROM eth0: ethernet@4a100000 Press SPACE to abort autoboot in 2 seconds board_name=[A335BNLT] ... board_rev=[0A5A] ... Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 Card did not respond to voltage select! Card did not respond to voltage select! ** First descriptor is NOT a primary desc on 1:1 ** switch to partitions #0, OK mmc1(part 0) is current device ** No partition table - mmc 1 ** gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 ** First descriptor is NOT a primary desc on 1:1 ** switch to partitions #0, OK mmc1(part 0) is current device ** First descriptor is NOT a primary desc on 1:1 ** gpio: pin 54 (gpio 54) value is 1 ** No partition table - mmc 1 ** Checking for: /uEnv.txt ... ** No partition table - mmc 1 ** Checking for: /boot.scr ... ** No partition table - mmc 1 ** Checking for: /boot/boot.scr ... ** No partition table - mmc 1 ** Checking for: /boot/uEnv.txt ... ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** ** No partition table - mmc 1 ** starting USB... USB0: Port not available. ethernet@4a100000 Waiting for PHY auto negotiation to complete Crap! Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAOCHtYjBVC82yWEsa%3Dfi2LH7nyTgcv-0hjkBN2YXbLka7uKE1w%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.