You need to exclude the lab by putting it's filename into '~addons/labs/labs/exlabs.txt' .
I tried your lab in a clean JQt session and got the same result. Well, I do some initialization before J is ready. But it shouldn't be a problem (I hope). Engine: j805/j64/windows Beta-14: commercial/2016-10-28T10:54:53 Library: 8.05.08 Qt IDE: 1.5.2s/5.6.2 Platform: Win 64 Installer: J805 install InstallPath: c:/program files/j64-805 Contact: www.jsoftware.com It crashes in runview. I turned on debug, first with ctrl-k then with 13!:0]1 to get closer to the failure but J crashes. Will play with it some more to see if I can track it down. On Mon, Nov 14, 2016 at 11:19 AM, robert therriault <[email protected]> wrote: > Hi Don, > > You are right about "Introduction to Video Labs" not running in JHS, in > fact I had thought that I had it set up so that it would only be shown in > the jqt labs and would not be visible in the JHS labs, but maybe Chris or > Bill can bring me up to speed on how I specify that. > > In jqt "Introduction to Video Labs" runs fine for me. You might take a > look to see if there are any orphan windows that think that they have > control. You can find the windows that are open using the following > technique. > > JVERSION > Engine: j805/j64/darwin > Beta-14: commercial/2016-10-28T11:59:13 > Library: 8.05.07 > Qt IDE: 1.5.2/5.6.2 > Platform: Darwin 64 > Installer: J805 install > InstallPath: /applications/j64-80514 > Contact: www.jsoftware.com > > wdforms '' NB. should give you a list of current windows > ┌──────────┬───────────────┬───────┬┬───┐ > │multimedia│140198256240224│qtvideo││631│ > └──────────┴───────────────┴───────┴┴───┘ > wd 'psel multimedia;pclose' NB. Let's you close windows that are not > needed > > Hope this helps. > > Cheers, bob > > > > On Nov 14, 2016, at 9:43 AM, Don Guinn <[email protected]> wrote: > > > > I was a little premature in sending that e-mail. Since then I have found > > several other labs that don't work under jhs. > > > > Dissect I > > Dissect II > > J by Point & Click I > > Debug > > All FVJ4 labs > > > > "Video Introduction to Labs" fails in both jhs and JQt. In JQt the > > following: > > |set : bad child id: mm > > : wd > > | (LF,~wd ::(''"_)'qer') (13!:8)3 > > > > It also uses "wd" so it won't work in jhs even if that is fixed. > > > > On Mon, Nov 14, 2016 at 8:45 AM, chris burke <[email protected]> > wrote: > > > >> Will do, thanks. > >> > >> On 14 November 2016 at 06:46, Don Guinn <[email protected]> wrote: > >> > >>> Need to add "labs/labs/core/jclickbeginners.ijt" to EXJHS in > >>> "addons/labs/labs/exlabs.txt" as it assumes that it is running under > JQt. > >>> ---------------------------------------------------------------------- > >>> For information about J forums see http://www.jsoftware.com/forums.htm > >> ---------------------------------------------------------------------- > >> For information about J forums see http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm > ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
