Do you fill the drum to the top with water to push the fumes out? and why the
dish wash?
Jewel
----- Original Message -----
From: Rob Monitor
To: [email protected]
Sent: Friday, June 29, 2007 3:00 AM
Subject: Re: [BlindHandyMan] Cutting Circles in Sheet Metal
Hi, yes Know all about putting water and a little dish soap in the drum
before cutting into it... Got about 60 55 gallon drums from a friend of mine
that had a paint shop and paint and other stuff came in the drums.. He tolled
me all about the hazard..
THANKS ROB -- Original Message -----
From: Bill Gallik
To: [email protected]
Sent: Thursday, June 28, 2007 3:16 AM
Subject: Re: [BlindHandyMan] Cutting Circles in Sheet Metal
Rob,
Be VERY CAREFUL when cutting that hole. What did the drum contain? Is there
any possibility of fumes that could explode when heated? You might want to
consider filling the drum with water before cutting the hole to eliminate
the possibility of a disastrous outcome.
When I was about 10 years old a 27 year old neighbor was killed while trying
to use a cutting torch on a storage drum. He left behind a pregnant wife
and a young family, what a pitiful situation that was.
----------------
Bill Gallik
E-Mail: [EMAIL PROTECTED]
- "Nothing changes your opinion of a friend so surely as success - yours or
his."
- Franklin P. Jones
----- Original Message -----
From: "Rob Monitor" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Wednesday, June 27, 2007 10:26 PM
Subject: Re: [BlindHandyMan] Cutting Circles in Sheet Metal
This is Rob again, Ray what I'm cutting the hole in is a 55 gallon oil drum
top. Do you think this nail cutting thing would work for that?? Also I do
have a router and could there be any way I could use that??
THANKS ROB
----- Original Message -----
From: Boyce, Ray
To: [email protected]
Sent: Wednesday, June 27, 2007 9:34 PM
Subject: [BlindHandyMan] Cutting Circles in Sheet Metal
Hi Rob
The cheapest form of a circle cutting jig is just a piece of wood with a
hole drilled as the centre point with a screw and nut to lock it in
position and a nail driven through at the desired diameter with the
point of the nail used as a cutting edge.
Just revolve it around until you cut through the metal if it becomes
dull use another sharp nail.
You can get metal cutting blades for a Jig Saw and circle cutting tin
snips also nibblers if you have a compressor.
Also there are things called trammels which have points both ends which
boiler makers use for marking out circles.
But for a one off cut try the wood and nail trick.
What you did not say is how thick this sheet metal is you are trying to
cut.
If it is really thin like sheet copper you could use scissors.
HTH
Ray
**********************************************************************
This message and its attachments may contain legally
privileged or confidential information. If you are not the
intended recipient, you must not disclose or use the
information contained in it. If you have received this e-mail
in error, please notify the sender immediately by return
e-mail and delete the e-mail.
Any content of this message and its attachments which
does not relate to the official business of Eraring Energy
must be taken not to have been sent or endorsed by
Eraring Energy. No warranty is made that the e-mail or
attachment(s) are free from computer virus or other defect.
**********************************************************************
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
------------------------------------------------------------------------------
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.476 / Virus Database: 269.9.10/875 - Release Date: 27/06/07 9:08
p.m.
[Non-text portions of this message have been removed]
