Oooooh, right--forgot about that discussion. b Sent from my 8-track deck
On Jan 23, 2012, at 11:19, Dennis Keating <[email protected]> wrote: > you will want to add a guage to the pressure regulator on your mains line if > you add that > > On 1/23/2012 11:24 AM, Benjamin McCafferty wrote: >> >> OK, sorry, I'm missing something. >> >> I ordered the p-stat from Chris' Coffee. Are you saying I'll need a new >> gauge also, i.e. that the stock one will no longer work? >> >> tx, >> bmc >> >> On Jan 23, 2012, at 10:20 AM, Dennis Keating wrote: >> >>> i'm looking at my spare presstat and therem are only wire id nos on it - no >>> p/n. the press regulator i use is grainger p/n 2A645. you will need a >>> gauge, too. >>> >>> On 1/22/2012 5:16 PM, Benjamin McCafferty wrote: >>>> >>>> Thanks Dennis, appreciate the reply. Stupid question--the pressure stat >>>> controls pressure in the steam boiler, yes? Does it also control idle >>>> pressure in the brew boiler? Recognizing that the OPV or setting on the >>>> rotary pump controls brew pressure. >>>> >>>> The black plastic seems to be what's leaking intermittently on mine--I'm >>>> pointing to the leak in the photo with my easter egg dipper, er, fancy >>>> grind stirrer and clump buster... >>>> >>>> Will get the new one ordered--do you happen to remember your part number? >>>> I'll look, perhaps there's only one. >>>> >>>> b >>>> >>>> On Jan 22, 2012, at 1:42 PM, Dennis Keating wrote: >>>> >>>>> Ben, thats the pressurestat . if the fitting that attaches the pipe >>>>> leaks, use teflon tape - if the part is leaking, replace. myself and >>>>> others upgrade to the Jaegerstat from chris coffee service, but a stock >>>>> $30 one works good. >>>>> >>>>> On 1/22/2012 9:05 AM, Benjamin McCafferty wrote: >>>>>> >>>>>> Thanks Stevie! >>>>>> I found the leak, and posted a picture in another message. I had the >>>>>> same failure you described, and added some silicon hose over the water >>>>>> line where it rubs. >>>>>> b >>>>>> >>>>>> On Jan 22, 2012, at 7:39 AM, StevieG. wrote: >>>>>> >>>>>>> Hi Ben - I had this same problem a while back, and found that the >>>>>>> plastic line from the back boiler had cracked where it was rubbing on >>>>>>> the top edge of the boiler. There was an indentation in the >>>>>>> insulation and the plastic was rubbing on the sharp edge. >>>>>>> >>>>>>> Just a thought.... >>>>>>> >>>>>>> -- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "Brewtus" group. >>>>>>> To post to this group, send email to [email protected]. >>>>>>> To unsubscribe from this group, send email to >>>>>>> [email protected]. >>>>>>> For more options, visit this group at >>>>>>> http://groups.google.com/group/brewtus?hl=en. >>>>>>> >>>>> >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google Groups >>>>> "Brewtus" group. >>>>> To post to this group, send email to [email protected]. >>>>> To unsubscribe from this group, send email to >>>>> [email protected]. >>>>> For more options, visit this group at >>>>> http://groups.google.com/group/brewtus?hl=en. >>>> >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "Brewtus" group. >>>> To post to this group, send email to [email protected]. >>>> To unsubscribe from this group, send email to >>>> [email protected]. >>>> For more options, visit this group at >>>> http://groups.google.com/group/brewtus?hl=en. >>> >>> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "Brewtus" group. >>> To post to this group, send email to [email protected]. >>> To unsubscribe from this group, send email to >>> [email protected]. >>> For more options, visit this group at >>> http://groups.google.com/group/brewtus?hl=en. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Brewtus" group. >> To post to this group, send email to [email protected]. >> To unsubscribe from this group, send email to >> [email protected]. >> For more options, visit this group at >> http://groups.google.com/group/brewtus?hl=en. > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group at > http://groups.google.com/group/brewtus?hl=en. -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/brewtus?hl=en.
