Pstat was my issue too when my pressure relief kept blowing. Seems to be a commonly replaced part on the Brewtus.
On Fri, Jun 19, 2020 at 11:51 AM triplereef . <[email protected]> wrote: > Yea - that's what i was thinking - a piece of sediment got in the pstat. > > Just found this video from WLL; he is saying the relief valvr starts to > open around 1.5 and pstat set to 1.3 > https://www.youtube.com/watch?v=WVKg4z3yhkI > > Thanks bmc - i appreciate the response. I should be good to go now. > > On Fri, Jun 19, 2020, 11:39 AM 'Benjamin McCafferty' via Brewtus < > [email protected]> wrote: > >> I believe mine blew off at about 2 bar, from memory. I ran pressure >> around 1.5 all the time. Thinking it through, I wonder if a piece of >> scale/mineral has gotten to the p-stat and caused it to stick? I.e. then it >> keeps heating the steam boiler unchecked until the valve opens? >> >> best, >> bmc >> >> On Jun 19, 2020, at 08:14, triplereef . <[email protected]> wrote: >> >> Question for you guys: >> >> At what pressure does your pressure relief valve connecting the steam >> wand start to open? >> >> I ask because i am troubleshooting this valve opening during normal >> heat-up at around 1.75 bar right now. I'm fairly sure my steam boulier >> usually sits at 1.5 bar but i havevn't paid much attention to it. >> >> My issue started after a two-flush descale i performed yesterday (it had >> been a while since my last descale) >> >> Thank you - trying to get my bearings for what correct pressure should be. >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Brewtus" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/brewtus/CAA-TRKoDMJnfxzLiD1j7BP5aH_iO6Z0VFKLVZ5YKvtrBnOgVOQ%40mail.gmail.com >> <https://groups.google.com/d/msgid/brewtus/CAA-TRKoDMJnfxzLiD1j7BP5aH_iO6Z0VFKLVZ5YKvtrBnOgVOQ%40mail.gmail.com?utm_medium=email&utm_source=footer> >> . >> <20200619_110746.jpg> >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Brewtus" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/brewtus/89429179-2E41-4AFC-9A17-DFCFF71EED74%40me.com >> <https://groups.google.com/d/msgid/brewtus/89429179-2E41-4AFC-9A17-DFCFF71EED74%40me.com?utm_medium=email&utm_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/brewtus/CAA-TRKpwexjc38E9jDrXYS_V3-8pqp6b4r-H5P9HhSkVj6NbSw%40mail.gmail.com > <https://groups.google.com/d/msgid/brewtus/CAA-TRKpwexjc38E9jDrXYS_V3-8pqp6b4r-H5P9HhSkVj6NbSw%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/brewtus/CAOJZtCLuNvQ3qL1TAU7Gja%3Dq%3DCLNbKLR8xmfSLYkAigvYkVYUQ%40mail.gmail.com.
