Hi Nimish, So the 11.4 and 11.5 tools are still supported with the latest libraries. If you run get_xlVersion() in your matlab prompt you should get 11.4. The script casper_xps.m checks the version number and prints the error. What does your get_xlVersion() output?
Wes On Mon, Oct 8, 2012 at 5:59 PM, Nimish Sane <[email protected]> wrote: > Hi Wes, > > I was able to use the ska-sa mlib_devel repository with Xilinx 11.4 and > Matlab 2009b earlier, and successfully compile my designs. With the latest > update, it seems I can no longer use these versions. The compilation fails > with an error that I have Xilinx 11.4 installed, which is not supported. Is > it now mandatory to upgrade to Xilinx14.2 and Matlab 2012a? > > Thanks, > > Nimish > > > On Sat, Oct 6, 2012 at 2:15 PM, Nimish Sane <[email protected]> wrote: > >> Hi Mark, >> >> That worked. After updating the libraries xsg core config was set to >> default Roach. >> >> Thanks, >> >> Nimish >> >> On Oct 5, 2012, at 6:10 PM, Mark Wagner <[email protected]> wrote: >> >> It's in both, you'll need to specify ROACH2 in the xsg_core_config block >> though. >> >> Mark >> >> >> On Fri, Oct 5, 2012 at 3:06 PM, Nimish Sane <[email protected]> wrote: >> >>> Mark, >>> >>> This is bwrc repo or ska-sa? I am using ska-sa and could not find it. >>> >>> Thanks, >>> >>> Nimish >>> >>> On Oct 5, 2012, at 6:01 PM, Mark Wagner <[email protected]> >>> wrote: >>> >>> Hi Nimish, >>> >>> If you pull the new 10gbe_v2 yellowblock from the most recent repo, all >>> of those options should be available - sfp+, roach2, etc. >>> >>> Mark >>> >>> >>> On Fri, Oct 5, 2012 at 2:57 PM, Nimish Sane <[email protected]>wrote: >>> >>>> Hi Wes, >>>> >>>> I just updated to the latest libraries. Great work! I am looking >>>> forward to using those. I have a quick question. Does ten_Gbe_v2 block >>>> support Roach2? The "port" parameter on the yellow block can be set to >>>> between 0 and 3. I understand that Roach 2 will have 6 CX4 ports (3 each >>>> per mezzanine card). How does that map to the yellow block? >>>> >>>> Also, I remember from the casper workshop that there was going to be a >>>> setting to select between CX4 and SFP+ connection. Do you know what's the >>>> status with that? >>>> >>>> Thanks, >>>> >>>> Nimish >>>> >>>> On Wed, Oct 3, 2012 at 8:10 AM, Andrew Martens <[email protected]>wrote: >>>> >>>>> Hi Dave, Wes >>>>> >>>>> We could probably write a little Wishbone-to-OPB module and plug that >>>>> in >>>>> front of the OPB yellow blocks for some things. Messing with the >>>>> internals of yellow blocks that we don't have hardware for could be >>>>> dangerous e.g ADCs. Ideally people would help out with yellow blocks >>>>> they have hardware for and have expertise in. >>>>> >>>>> Regards >>>>> Andrew >>>>> >>>>> On Wed, 2012-10-03 at 13:29 +0200, Wesley New wrote: >>>>> > Hi Dave, >>>>> > >>>>> > >>>>> > Unfortunately the move to wishbone will need to be done en mass. >>>>> > >>>>> > >>>>> > Wes >>>>> > >>>>> > On Thu, Sep 27, 2012 at 7:40 PM, David MacMahon >>>>> > <[email protected]> wrote: >>>>> > Hi, Wes, >>>>> > >>>>> > Are you converting all yellow blocks to wishbone en masse or >>>>> > can they be converted one by one over time? >>>>> > >>>>> > Thanks, >>>>> > Dave >>>>> > >>>>> > On Sep 27, 2012, at 10:23 AM, Wesley New wrote: >>>>> > >>>>> > > Hi Rurik >>>>> > > >>>>> > > These updates don't contain the wishbone port, that is the >>>>> > next item >>>>> > > on my to-do list. >>>>> > > >>>>> > > Wes >>>>> > > >>>>> > > On 9/27/12, Rurik A. Primiani <[email protected]> >>>>> > wrote: >>>>> > >> Hi Wes, >>>>> > >> >>>>> > >> Great work! I look forward to using the newer tools. Just >>>>> a >>>>> > quick >>>>> > >> question, does this update include the migration to the >>>>> > Wishbone bus >>>>> > >> discussed at the workshop? >>>>> > >> >>>>> > >> Best, >>>>> > >> Rurik >>>>> > >> >>>>> > >> On 9/26/12 9:01 AM, Wesley New wrote: >>>>> > >>> Good Day all, >>>>> > >>> >>>>> > >>> We have updated the existing MSSGE toolflow to work with >>>>> > the Xilinx 14.2 >>>>> > >>> tools and Matlab2012a. I have provided a wikipage with >>>>> all >>>>> > the details >>>>> > >>> and how to get an environment setup, available at: >>>>> > >>> >>>>> > >>>>> https://casper.berkeley.edu/wiki/MSSGE_Setup_with_Xilinx_14.2_and_Matlab_2012a >>>>> > >>> >>>>> > >>> >>>>> > >>> The ska-sa mlib_devel repository currently hosts these >>>>> > changes and can >>>>> > >>> be found at: https://github.com/ska-sa/mlib_devel. So >>>>> feel >>>>> > free to start >>>>> > >>> using the latest tools and post any issues/feeback to the >>>>> > mailing list. >>>>> > >>> >>>>> > >>> Thanks >>>>> > >>> >>>>> > >>> Wesley >>>>> > >> >>>>> > > >>>>> > >>>>> > >>>>> > >>>>> > >>>>> >>>>> >>>>> >>>>> >>>> >>> >> >
