Dear,
Perhaps I will say mistakes, but I can read :
7613#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.232, VC ID: 7232183, VC status: up
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: active
No adjacency
=> For me it is not correct.
On your 3600 :
3600#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.7, VC ID: 7232183, VC status: down
Last error: Remote peer access circuit is down
Output interface: Vl925, imposed label stack {281}
Preferred path: not configured
Default path: active
Next hop: 172.20.202.49
Regards,
Christophe
Le 2015-03-24 09:00, Mohammad Khalil a écrit :
3600#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.7, VC ID: 7232183, VC status: down
Last error: Remote peer access circuit is down
Output interface: Vl925, imposed label stack {281}
Preferred path: not configured
Default path: active
Next hop: 172.20.202.49
Create time: 02:59:58, last status change time: 00:00:02
Last label FSM state change time: 00:01:38
Signaling protocol: LDP, peer 172.20.40.7:0 up
Targeted Hello: 172.20.40.232(LDP Id) -> 172.20.40.7, LDP is UP
Graceful restart: not configured and not enabled
Non stop routing: not configured and not enabled
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LruRrd
Last local dataplane status rcvd: No fault
Last BFD dataplane status rcvd: Not sent
Last BFD peer monitor status rcvd: No fault
Last local AC circuit status rcvd: No fault
Last local AC circuit status sent: DOWN AC(rx/tx faults)
Last local PW i/f circ status rcvd: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: DOWN AC(rx/tx faults)
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 2042, remote 281
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description: AMAAL_TEST
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
Dataplane:
SSM segment/switch IDs: 475811/242336 (used), PWID: 44
VC statistics:
transit packet totals: receive 0, send 16
transit byte totals: receive 0, send 1200
transit packet drops: receive 0, seq error 0, send 0
7613#sh mpls l2transport vc 7232183 detail
Local interface: Vl183 up, line protocol up, Eth VLAN 183 up
Interworking type is Ethernet
Destination address: 172.20.40.232, VC ID: 7232183, VC status: up
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: active
No adjacency
Create time: 03:12:56, last status change time: 00:00:03
Signaling protocol: LDP, peer 172.20.40.232:0 up
Targeted Hello: 172.20.40.7(LDP Id) -> 172.20.40.232, LDP is UP
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LrdRru
Last local dataplane status rcvd: No fault
Last local SSS circuit status rcvd: DOWN AC(rx/tx faults)
Last local SSS circuit status sent: No fault
Last local LDP TLV status sent: DOWN AC(rx/tx faults)
Last remote LDP TLV status rcvd: No fault
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 281, remote 2042
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description: AMAAL_TEST
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
VC statistics:
transit packet totals: receive 16, send 0
transit byte totals: receive 960, send 0
transit packet drops: receive 0, seq error 0, send 0
To: [email protected]
From: [email protected]
Date: Tue, 24 Mar 2015 09:54:47 +0200
Subject: Re: [c-nsp] AToM
On 24/Mar/15 09:49, Mohammad Khalil wrote:
> Hi all
> I am trying to establish AToM between 7613 and 3600
> The module from the 7613 side is 7600 ES+ 20xGE SFP
>
> 3600#sh run int vlan 183
> interface Vlan183
> no ip address
> xconnect 172.20.40.7 7232183 encapsulation mpls
>
> 7613#sh run int vlan 183
> interface Vlan183
> no ip address
> load-interval 30
> xconnect 172.20.40.232 7232183 encapsulation mpls
>
> 7613#sh mpls l2transport vc 7232183
>
> Local intf Local circuit Dest address VC ID Status
> ------------- -------------------------- --------------- ----------
----------
> Vl183 Eth VLAN 183 172.20.40.232 7232183 UP
>
> 3600#sh mpls l2transport vc 7232183
>
> Local intf Local circuit Dest address VC ID Status
> ------------- -------------------------- --------------- ----------
----------
> Vl183 Eth VLAN 183 172.20.40.7 7232183 DOWN
>
> I have tried to configure L3VPN (VRF on both routers and test loopback
interfaces) and it worked fine
>
> Any ideas?
Detailed output?
Mark.
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
--
Christophe Lucas
http://www.clucas.fr/blog/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
