Yeah, I think slowing down more and using the fan less(read: almost never) is the solution to the cracks we are getting in some parts. On 2013-09-27 3:12 PM, "d-_-b" <thor.robin...@gmail.com> wrote:
> Parts with fine detail can be run with a lower minimum speed ( default > 10mm/s ). we ran the second triforce at 1mm/s minimum speed and that was a > tad low, but gave us excellent detail. > > > On Fri, Sep 27, 2013 at 10:36 AM, Stefan H.A <stefan...@gmail.com> wrote: > >> I've added some useful links to the tuning section of 3d printer wiki >> page. >> >> Based on the 'too cold' section of the trouble shooting guide I beleive >> we are cooling the part too much with the fan. I think that when printing >> with ABS the fan should remain off unless absolutely necessary (ie. Very >> short layers). Thinking back to the triforce, it only had trouble at the >> very top where the layers were taking only few seconds. >> On 2013-09-26 12:14 AM, "Stefan H.A" <stefan...@gmail.com> wrote: >> >>> Be advised, I changed the infill patern to honeycomb. Don't be alarmed >>> if the printer appears to have a convulsion while printing infill. Do keep >>> an eye out for screws coming loose. >>> >>> I've also set it to print a solid layer every 40 layers. These settings >>> should increase part strength considerably. >>> On 2013-09-24 3:39 PM, "Benjamin Bergman" <b...@benbergman.ca> wrote: >>> >>>> The second one I linked (http://www.thingiverse.com/thing:124533) is >>>> basically a proper version of the one that I cobbled together months >>>> ago that we are currently using. No disassembly required to install >>>> that one. >>>> >>>> It would have been nice if all their end plates had cutouts for t-nuts >>>> to be inserted, like the main back plate has. It would make upgrading >>>> things way easier. >>>> >>>> On Tue, Sep 24, 2013 at 3:18 PM, Stefan H.A <stefan...@gmail.com> >>>> wrote: >>>> > Depending where the bracket attaches, the printer may need to be >>>> partially >>>> > disassembled to add the t-nuts into the channels (looks like that may >>>> be the >>>> > case for the top most screw). I have been looking for a solution that >>>> only >>>> > needs t-nuts in accessable channels. >>>> > >>>> > On 2013-09-24 3:09 PM, "Brian Kulyk" <br...@kulyk.ca> wrote: >>>> >> >>>> >> I like the first one Ben suggested >>>> >> (http://www.thingiverse.com/thing:77301/#remixes) >>>> >> >>>> >> >>>> >> Brian Kulyk >>>> >> 204.887.6988 >>>> >> >>>> >> >>>> >> On Tue, Sep 24, 2013 at 1:50 PM, Benjamin Bergman <b...@benbergman.ca >>>> > >>>> >> wrote: >>>> >>> >>>> >>> A few more options (all designed to attach to the MendelMax 2.0): >>>> >>> http://www.thingiverse.com/thing:77301/#remixes >>>> >>> http://www.thingiverse.com/thing:124533 >>>> >>> http://www.thingiverse.com/thing:78741 >>>> >>> >>>> >>> On Tue, Sep 24, 2013 at 12:33 PM, Stefan H.A <stefan...@gmail.com> >>>> wrote: >>>> >>> > This would probably work but a stand alone spool would take more >>>> space. >>>> >>> > The >>>> >>> > brackets I posted look like they could be attached to the back of >>>> >>> > printer. >>>> >>> > >>>> >>> > On 2013-09-24 11:32 AM, "d-_-b" <thor.robin...@gmail.com> wrote: >>>> >>> >> >>>> >>> >> http://www.thingiverse.com/thing:52927 <- another option for >>>> the >>>> >>> >> spool >>>> >>> >> holder >>>> >>> >> >>>> >>> >> >>>> >>> >> On Mon, Sep 23, 2013 at 12:28 PM, Stefan H.A < >>>> stefan...@gmail.com> >>>> >>> >> wrote: >>>> >>> >>> >>>> >>> >>> Some interesting and helpful links I found surfing thingiverse >>>> and >>>> >>> >>> the >>>> >>> >>> reprap wiki. >>>> >>> >>> >>>> >>> >>> This might work for a spool holder. >>>> >>> >>> >>>> >>> >>> http://www.thingiverse.com/thing:63431 >>>> >>> >>> >>>> >>> >>> Some info about abs and pla. Note the suggestions regarding >>>> print >>>> >>> >>> surface. >>>> >>> >>> >>>> >>> >>> http://reprap.org/wiki/ABS >>>> >>> >>> >>>> >>> >>> http://reprap.org/wiki/PLA >>>> >>> >>> >>>> >>> >>> Marlin firmware's home page which includes a list of >>>> implimented G >>>> >>> >>> and M >>>> >>> >>> codes. >>>> >>> >>> >>>> >>> >>> https://github.com/ErikZalm/Marlin >>>> >>> >>> >>>> >>> >>> On 2013-08-28 1:00 PM, "Aemilianus Kehler" <zew...@gmail.com> >>>> wrote: >>>> >>> >>>> >>>> >>> >>>> Stupid huffer, why don't you learn to share? >>>> >>> >>>> >>>> >>> >>>> Cheers!! >>>> >>> >>>> >>>> >>> >>>> On Aug 27, 2013, at 5:04 PM, Justin Lacko <jus...@takaji.ca> >>>> wrote: >>>> >>> >>>> >>>> >>> >>>> Of course I huffed it all! How else could I say I'm on such a >>>> long >>>> >>> >>>> "trip" to "Denmark"? >>>> >>> >>>> >>>> >>> >>>> >>>> >>> >>>> On 27 August 2013 23:59, Jim MacKenzie <protoj...@gmail.com> >>>> wrote: >>>> >>> >>>>> >>>> >>> >>>>> He probably huffed it all. >>>> >>> >>>>> >>>> >>> >>>>> On Aug 27, 2013 4:58 PM, "Roswyne" <rosw...@gmail.com> wrote: >>>> >>> >>>>>> >>>> >>> >>>>>> Justin had a 1L tin of it, IIRC. I doubt he took it to >>>> Denmark! >>>> >>> >>>>>> >>>> >>> >>>>>> On Aug 27, 2013 4:26 PM, "Stefan H.A" <stefan...@gmail.com> >>>> wrote: >>>> >>> >>>>>>> >>>> >>> >>>>>>> I am thinking it might be good to have one thread for all >>>> things >>>> >>> >>>>>>> 3d >>>> >>> >>>>>>> printer so I am starting one. >>>> >>> >>>>>>> >>>> >>> >>>>>>> FYI - I won't be able to make it to the space until sometime >>>> >>> >>>>>>> after >>>> >>> >>>>>>> the meeting, not sure when though. My cousin is visiting >>>> from >>>> >>> >>>>>>> Iceland and >>>> >>> >>>>>>> she is interested in seeing the 3d printer so I'll be >>>> bringing >>>> >>> >>>>>>> her along. >>>> >>> >>>>>>> >>>> >>> >>>>>>> Also I hope to pick up some nail polish remover (acetone) to >>>> >>> >>>>>>> clean >>>> >>> >>>>>>> the print bed and maybe checking out the heated bed as it >>>> has >>>> >>> >>>>>>> been acting >>>> >>> >>>>>>> up. >>>> >>> >>>>>>> >>>> >>> >>>>>>> _______________________________________________ >>>> >>> >>>>>>> SkullSpace Discuss Mailing List >>>> >>> >>>>>>> Help: >>>> >>> >>>>>>> >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>>>>>> Archive: >>>> >>> >>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >>>>>> >>>> >>> >>>>>> >>>> >>> >>>>>> _______________________________________________ >>>> >>> >>>>>> SkullSpace Discuss Mailing List >>>> >>> >>>>>> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>>>>> Archive: >>>> >>> >>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >>>>> >>>> >>> >>>>> >>>> >>> >>>>> _______________________________________________ >>>> >>> >>>>> SkullSpace Discuss Mailing List >>>> >>> >>>>> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>>>> Archive: >>>> >>> >>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >>>> >>>> >>> >>>> >>>> >>> >>>> _______________________________________________ >>>> >>> >>>> SkullSpace Discuss Mailing List >>>> >>> >>>> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>>> Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >>>> >>>> >>> >>>> >>>> >>> >>>> _______________________________________________ >>>> >>> >>>> SkullSpace Discuss Mailing List >>>> >>> >>>> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>>> Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >>> >>>> >>> >>> >>>> >>> >>> _______________________________________________ >>>> >>> >>> SkullSpace Discuss Mailing List >>>> >>> >>> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >>> Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >> >>>> >>> >> >>>> >>> >> >>>> >>> >> >>>> >>> >> -- >>>> >>> >> -- >>>> >>> >> ) thor.robinson; >>>> >>> >> ) icon/phreshlyspun/ppca/skullspace >>>> >>> >> >>>> >>> >> -----BEGIN GEEK CODE BLOCK----- >>>> >>> >> Version: 3.12 >>>> >>> >> GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ E---- W@ N! o K? w--- >>>> >>> >> O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ DI++ D++ G+ e* h-- r y+ >>>> z+ >>>> >>> >> ------END GEEK CODE BLOCK------ >>>> >>> >> >>>> >>> >> _______________________________________________ >>>> >>> >> SkullSpace Discuss Mailing List >>>> >>> >> Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> >> Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> > >>>> >>> > >>>> >>> > _______________________________________________ >>>> >>> > SkullSpace Discuss Mailing List >>>> >>> > Help: >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> > Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> _______________________________________________ >>>> >>> SkullSpace Discuss Mailing List >>>> >>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >>> Archive: >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>> >> >>>> >> >>>> >> >>>> >> _______________________________________________ >>>> >> SkullSpace Discuss Mailing List >>>> >> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> >> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>> > >>>> > >>>> > _______________________________________________ >>>> > SkullSpace Discuss Mailing List >>>> > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> > Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>> _______________________________________________ >>>> SkullSpace Discuss Mailing List >>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>> >>> >> _______________________________________________ >> SkullSpace Discuss Mailing List >> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >> > > > > -- > -- > ) thor.robinson; > ) icon/phreshlyspun/ppca/skullspace > > -----BEGIN GEEK CODE BLOCK----- > Version: 3.12 > GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ E---- W@ N! o K? w--- > O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ DI++ D++ G+ e* h-- r y+ z+ > ------END GEEK CODE BLOCK------ > > _______________________________________________ > SkullSpace Discuss Mailing List > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss > Archive: https://groups.google.com/group/skullspace-discuss-archive/ >
_______________________________________________ SkullSpace Discuss Mailing List Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss Archive: https://groups.google.com/group/skullspace-discuss-archive/
