Yup, you are right. The manual clearly states that PB CTRL only affects CW and Data modes, and shifts the increment between 0.05 and .01 KHz. It appears to be fixed at .1 KHz for SSB for both low and hi cut. Those increments work pretty well as is.
73, Jack, W6FB > On Jun 30, 2018, at 8:44 PM, Michael Gillen <[email protected]> wrote: > > Hmmm when I try that I get Shif=.05 however and when I turn VFO-A it says N/A > and it still moves in .10 increments? > > >> On Jun 30, 2018, at 7:55 PM, Jack Brindle <[email protected]> wrote: >> >> PB CTRL should do what you want. See page 62 of the K3S manual. >> >> Jack, W6FB >> >>> On Jun 30, 2018, at 7:31 PM, Michael Gillen via Elecraft >>> <[email protected]> wrote: >>> >>> Good info on the filters I had never tried the LO/HI CUT and I like it. One >>> question: On my K3S I cannot set the LO CUT to .35KHz it only steps in .10 >>> increments not 0.05 increments is there some CONFIG item I need to change? >>> I looked through the CONFIG menus and Fred Cady’s book however I did not >>> see anything about setting that step. >>> >>> 73, >>> Michael >>> KK6RWK >>> >>> >>>> On Jun 30, 2018, at 5:37 PM, Bill Frantz <[email protected]> wrote: >>>> >>>> Congratulations. The K3 is a really nice radio with extraordinary factory >>>> support. >>>> >>>> For SSB, I set low cut to .35 KHz and adjust the upper cut between 1.9 KHz >>>> and 2.8 KHz, depending on conditions. Higher makes for easier copy, but >>>> lower will eliminate more noise, and help with nearby stations. Remember, >>>> the crystal filters are to protect the AtoD converter in the receiver. The >>>> DSP has many useful settings between those of the installed filters. >>>> >>>> 73 Bill AE6JV >>>> >>>> On 6/30/18 at 5:07 PM, [email protected] (Bill) wrote: >>>> >>>>> I recently purchased a K3 and trying to set up for SSB.I do not do code. >>>>> Is there any recommended settings for the shift lo cut and width? >>>>> It has the KFL3A-400 and the KFL3A-12.8 8 pole filters installed >>>>> I have read the manual and it does not really help me. >>>>> Thanks >>>>> Bill >>>>> W3WGG >>>> >>>> --------------------------------------------------------------------------- >>>> Bill Frantz | Re: Computer reliability, performance, and security: >>>> 408-356-8506 | The guy who *is* wearing a parachute is *not* the >>>> www.pwpconsult.com | first to reach the ground. - Terence Kelly >>>> >>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >>>> Message delivered to [email protected] >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >> > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
