Yes its working well thank you for the advice!
> On Jun 30, 2018, at 9:31 PM, Jack Brindle <[email protected]> wrote: > > Yup, you are right. The manual clearly states that PB CTRL only affects CW > and Data modes, and shifts the increment between 0.05 and .01 KHz. > It appears to be fixed at .1 KHz for SSB for both low and hi cut. Those > increments work pretty well as is. > > 73, > Jack, W6FB > >> On Jun 30, 2018, at 8:44 PM, Michael Gillen <[email protected]> wrote: >> >> Hmmm when I try that I get Shif=.05 however and when I turn VFO-A it says >> N/A and it still moves in .10 increments? >> >> >>> On Jun 30, 2018, at 7:55 PM, Jack Brindle <[email protected]> wrote: >>> >>> PB CTRL should do what you want. See page 62 of the K3S manual. >>> >>> Jack, W6FB >>> >>>> On Jun 30, 2018, at 7:31 PM, Michael Gillen via Elecraft >>>> <[email protected]> wrote: >>>> >>>> Good info on the filters I had never tried the LO/HI CUT and I like it. >>>> One question: On my K3S I cannot set the LO CUT to .35KHz it only steps in >>>> .10 increments not 0.05 increments is there some CONFIG item I need to >>>> change? I looked through the CONFIG menus and Fred Cady’s book however I >>>> did not see anything about setting that step. >>>> >>>> 73, >>>> Michael >>>> KK6RWK >>>> >>>> >>>>> On Jun 30, 2018, at 5:37 PM, Bill Frantz <[email protected]> wrote: >>>>> >>>>> Congratulations. The K3 is a really nice radio with extraordinary factory >>>>> support. >>>>> >>>>> For SSB, I set low cut to .35 KHz and adjust the upper cut between 1.9 >>>>> KHz and 2.8 KHz, depending on conditions. Higher makes for easier copy, >>>>> but lower will eliminate more noise, and help with nearby stations. >>>>> Remember, the crystal filters are to protect the AtoD converter in the >>>>> receiver. The DSP has many useful settings between those of the installed >>>>> filters. >>>>> >>>>> 73 Bill AE6JV >>>>> >>>>> On 6/30/18 at 5:07 PM, [email protected] (Bill) wrote: >>>>> >>>>>> I recently purchased a K3 and trying to set up for SSB.I do not do code. >>>>>> Is there any recommended settings for the shift lo cut and width? >>>>>> It has the KFL3A-400 and the KFL3A-12.8 8 pole filters installed >>>>>> I have read the manual and it does not really help me. >>>>>> Thanks >>>>>> Bill >>>>>> W3WGG >>>>> >>>>> --------------------------------------------------------------------------- >>>>> Bill Frantz | Re: Computer reliability, performance, and security: >>>>> 408-356-8506 | The guy who *is* wearing a parachute is *not* the >>>>> www.pwpconsult.com | first to reach the ground. - Terence Kelly >>>>> >>>>> ______________________________________________________________ >>>>> Elecraft mailing list >>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>> Post: mailto:[email protected] >>>>> >>>>> This list hosted by: http://www.qsl.net >>>>> Please help support this email list: http://www.qsl.net/donate.html >>>>> Message delivered to [email protected] >>>> >>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >>>> Message delivered to [email protected] >>> >> > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
