We ordered the 1024ppr encoder (EM1-2-1024-I): http://www.usdigital.com/products/encoders/incremental/modules/EM1#description with this disk: http://www.usdigital.com/products/encoders/incremental/rotary/disks/DISK-2 and this cable: http://www.usdigital.com/products/cables-connectors/cables/5-pin/CA-C5-SH-NC
Attached is a link to the only (stp) file I could find of the encoder mount. I tapped the small holes in this bracket by hand with a 4-40 tap (don’t tell anyone I used SAE screws on a metric only machine!) to mount the encoder to it. The countersunk holes (using an M4 screw I believe) held this mount to the backplate of the encoder housing with the same screws that held the EMCO encoder to it.. I then adjusted the encoder wheel to line up in the slot as it should using the stock Emco disk mounting hardware which is adjustable. I can’t be sure that I didn’t modify the dimensions of this drawing for the final part but I don’t recall doing that. I usually have my gcode or job file but I can’t seem to find them. I was only making one so I may have failed to save it… bgp.nu:/~tom/pub/EMCO120P-NewEncoderBrakt.stp -Tom > On Jan 22, 2016, at 4:50 PM, Drew Rogge <d...@dasrogges.com> wrote: > > Hi Tom, > > How did you end up mounting the new encoder to your EMCO? I'd like to do the > same thing to mine. > > Drew > > On 1/22/16 7:58 AM, tom-...@bgp.nu wrote: >> >> However, I often see videos of machining centers just spinning way a high >> speed tapping like it’s no big deal. Should I be tapping at much higher >> spindle speed in order to have more torque? Will the spindle be able to >> stop and reverse at those speeds to pull it off? I have aggressive >> start/stop settings on the VFD that controls the spindle, the encoder is >> 1024ppr quadrature…. >> >> >> -Tom >> >> >> ------------------------------------------------------------------------------ >> Site24x7 APM Insight: Get Deep Visibility into Application Performance >> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month >> Monitor end-to-end web transactions and take corrective actions now >> Troubleshoot faster and improve end-user experience. Signup Now! >> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > -- > Drew Rogge > d...@dasrogges.com > > Phone: 8934OOO629OO4829631OOOOOOO > > > ------------------------------------------------------------------------------ > Site24x7 APM Insight: Get Deep Visibility into Application Performance > APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month > Monitor end-to-end web transactions and take corrective actions now > Troubleshoot faster and improve end-user experience. Signup Now! > http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Site24x7 APM Insight: Get Deep Visibility into Application Performance APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor end-to-end web transactions and take corrective actions now Troubleshoot faster and improve end-user experience. Signup Now! http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
