On Sun, 2017-04-23 at 19:02 +0200, Peter Blodow wrote: > Long time ago, pncconf had an error, so that it made 5 steps to a cycle > instead of 4. This made the same symptoms at the steppers as you > picture. What version of pncconf are you using? > > Peter Blodow
it is the version that comes with LinuxCNC 2.7.8 > > Am 23.04.2017 um 14:50 schrieb Valerio Bellizzomi: > > On Sun, 2017-04-23 at 08:21 -0400, Todd Zuercher wrote: > >> With a stepper that usually means the motor is stalled usually because of > >> too high velocity, acceleration, or a wiring problem (bad connection on > >> one phase). > > the motor moves accordingly when I jog in Axis interface, and the > > microstep scale is ok > > > > I think if a bad connection was there, the motor could not move > > > > > > > > > >> ----- Original Message ----- > >> From: "Valerio Bellizzomi" <vale...@selnet.org> > >> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> > >> Sent: Sunday, April 23, 2017 2:46:03 AM > >> Subject: Re: [Emc-users] how to configure motors in pncconf? > >> > >> On Sat, 2017-04-22 at 10:24 +0200, Valerio Bellizzomi wrote: > >>> On Fri, 2017-04-21 at 11:56 +0100, andy pugh wrote: > >>>> On 21 April 2017 at 11:45, Valerio Bellizzomi <vale...@selnet.org> wrote: > >>>>> The X stepgen is show as 5 in the tab, and as > >>>>> hm2_5i25.0.stepgen.05.counts in the test window, and it is changing > >>>>> while I press the movement button > >>>> I think this is the problem. > >>>> > >>>> https://github.com/LinuxCNC/hostmot2-firmware/blob/master/src/PIN_7I76x2_34.vhd > >>>> > >>>> Shows stepgen.05 to be on the expansion connector, not the DB25. > >>>> > >>>> Configure the X axis to be on Connector 3. > >> Hello, > >> What does it means when motor vibrates and makes sounds ? > >> > >> The test window of pncconf is limited to 5000 and has disabled arrow > >> control, that means we can't set nothing higher than 5000. So, once > >> generated the config files with pncconf, I have edited the files by > >> hand, and now I am testing with Axis. > >> > >> now I have set the parameters as follows: > >> > >> step on-time 5000 > >> step space 5000 > >> dir setup 10000 > >> dir hold 10000 > >> > >> When the motor is at rest (before any jog command within Axis), it does > >> not vibrate. But once a command is given, when it goes at rest again it > >> vibrates and makes sounds, until I disable from the Axis interface. > >> > >> > >> > >> > >> ------------------------------------------------------------------------------ > >> Check out the vibrant tech community on one of the world's most > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot > >> _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> ------------------------------------------------------------------------------ > >> Check out the vibrant tech community on one of the world's most > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot > >> _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > ------------------------------------------------------------------------------ > > Check out the vibrant tech community on one of the world's most > > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > --- > Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft. > https://www.avast.com/antivirus > > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
