C5G124-48P2 I will unplug the Ethernet cables and try again.
On Oct 28, 2011, at 11:57 AM, "Jolie, David" <[email protected]> wrote: > Most likely they are shared - which product specifically. > > -----Original Message----- > From: Jason Grubbs [mailto:[email protected]] > Sent: Friday, October 28, 2011 11:54 AM > To: Enterasys Customer Mailing List > Subject: Re: [enterasys] <no subject> > > Are 45, 46, 47, and 48 shared ports? Meaning if I have a patch cable plugged > into 45 and a gbic plugged into 45, will they both work? > > On 10/28/11 11:36 AM, "Hopkins, Bruce" <[email protected]> wrote: > >> Switch your fiber strands around on one end and make sure RX and TX are >> matching up. I'm assuming you have matching GBICs such as Multimode or >> Single Mode. If you still don't get a light, turn your autonegioation >> off on the uplink ports and check to ensure the ports are >> administratively up. If all those things are good, then its likely fiber. >> >> >> >> -----Original Message----- >> From: Jason Grubbs [mailto:[email protected]] >> Sent: Friday, October 28, 2011 11:14 AM >> To: Enterasys Customer Mailing List >> Subject: Re: [enterasys] <no subject> >> >> Hello All, >> >> I am now trying to uplink two network closets together using GBICs but >> the ports aren't lighting up. Are there any special commands to >> configure on the GBIC ports to get them to uplink? >> >> Jason Grubbs >> Network Engineer >> Pottsgrove School District >> >> From: "Pluim, Jeremiah" >> <[email protected]<mailto:[email protected]>> >> Reply-To: "[email protected]<mailto:[email protected]>" >> <[email protected]<mailto:[email protected]>> >> Date: Tue, 25 Oct 2011 15:13:09 -0400 >> To: Enterasys Customer Mailing List >> <[email protected]<mailto:[email protected]>> >> Subject: RE: [enterasys] <no subject> >> >> I had same problem, was Cisco trained. I took some of Enterasys's >> bootcamps. They are very helpful. GTAC is helpful too. >> >> >> Jeremiah Pluim, Network Administrator II Avery Weigh-Tronix LLC >> >> >> -----Original Message----- >> From: Jason Grubbs [mailto:[email protected]] >> Sent: Tuesday, October 25, 2011 2:10 PM >> To: Enterasys Customer Mailing List >> Subject: Re: [enterasys] <no subject> >> >> I am having trouble getting them configured at all. The commands are >> very different than on Cisco switches. >> >> I know I have to create all of the vlans on the Enterasys switches >> because they don't recognize VTP but I am not having any luck. >> >> Jason Grubbs >> Network Engineer >> Pottsgrove School District >> >> From: "Borel, Reese" >> <[email protected]<mailto:[email protected]><mailto:[email protected]>> >> Reply-To: >> "[email protected]<mailto:[email protected]><mailto:e >> nte >> [email protected]>" >> <[email protected]<mailto:[email protected]><mailto:e >> nte >> [email protected]>> >> Date: Tue, 25 Oct 2011 14:52:15 -0400 >> To: Enterasys Customer Mailing List >> <[email protected]<mailto:[email protected]><mailto:e >> nte >> [email protected]>> >> Subject: RE:[enterasys] <no subject> >> >> What is the problem you are having? We have Enterasys to Cisco back to >> Enterasys and vice versa... Sending trunked vlans both directions. >> >> Thanks, >> Reese >> >> -----Original Message----- >> From: Jason Grubbs [mailto:[email protected]] >> Sent: Tuesday, October 25, 2011 1:47 PM >> To: Enterasys Customer Mailing List >> Subject: [enterasys] <no subject> >> >> Hello All, >> >> Until now, we have been a Cisco network. We recently purchased >> Enterasys switches and I am having trouble getting them connected to >> our Cisco network. Does anyone have any experience adding Enterasys >> switches to a Cisco network? >> >> >> ________________________________ >> This email and any files transmitted with it are to be treated as >> confidential and as such are not to be used or disclosed except for the >> purpose for which it has been sent. Any views or opinions presented in >> this e-mail are solely those of the author and do not represent those >> of the Pottsgrove School District. The School District accepts no >> liability for any damage caused by this e-mail. The recipient is >> required to indemnify the School District against any claims for loss >> or damage caused by any viruses or otherwise. >> >> --- >> To unsubscribe from enterasys, send email to >> [email protected]<mailto:[email protected]><mailto:[email protected]> with >> the body: unsubscribe enterasys >> [email protected]<mailto:[email protected]><mailto:[email protected]> >> >> >> --- >> To unsubscribe from enterasys, send email to >> [email protected]<mailto:[email protected]><mailto:[email protected]> with >> the body: unsubscribe enterasys >> [email protected]<mailto:[email protected]><mailto:[email protected]> >> >> >> --- >> To unsubscribe from enterasys, send email to >> [email protected]<mailto:[email protected]> with the >> body: unsubscribe enterasys >> [email protected]<mailto:[email protected]> >> >> --- >> To unsubscribe from enterasys, send email to >> [email protected]<mailto:[email protected]> with the body: unsubscribe >> enterasys >> [email protected]<mailto:[email protected] >> m> >> >> >> --- >> To unsubscribe from enterasys, send email to >> [email protected]<mailto:[email protected]> with the body: unsubscribe >> enterasys [email protected]<mailto:[email protected]> >> >> >> --- >> To unsubscribe from enterasys, send email to [email protected] with the >> body: unsubscribe enterasys [email protected] >> >> >> >> --- >> To unsubscribe from enterasys, send email to [email protected] with the >> body: unsubscribe enterasys [email protected] > > > --- > To unsubscribe from enterasys, send email to [email protected] with the body: > unsubscribe enterasys [email protected] > > --- > To unsubscribe from enterasys, send email to [email protected] with the body: > unsubscribe enterasys [email protected] --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected]
