Are 45, 46, 47, and 48 shared ports? Meaning if I have a patch cable plugged into 45 and a gbic plugged into 45, will they both work?
On 10/28/11 11:36 AM, "Hopkins, Bruce" <[email protected]> wrote: >Switch your fiber strands around on one end and make sure RX and TX are >matching up. I'm assuming you have matching GBICs such as Multimode or >Single Mode. If you still don't get a light, turn your autonegioation off >on the uplink ports and check to ensure the ports are administratively >up. If all those things are good, then its likely fiber. > > > >-----Original Message----- >From: Jason Grubbs [mailto:[email protected]] >Sent: Friday, October 28, 2011 11:14 AM >To: Enterasys Customer Mailing List >Subject: Re: [enterasys] <no subject> > >Hello All, > >I am now trying to uplink two network closets together using GBICs but >the ports aren't lighting up. Are there any special commands to >configure on the GBIC ports to get them to uplink? > >Jason Grubbs >Network Engineer >Pottsgrove School District > >From: "Pluim, Jeremiah" ><[email protected]<mailto:[email protected]>> >Reply-To: "[email protected]<mailto:[email protected]>" ><[email protected]<mailto:[email protected]>> >Date: Tue, 25 Oct 2011 15:13:09 -0400 >To: Enterasys Customer Mailing List ><[email protected]<mailto:[email protected]>> >Subject: RE: [enterasys] <no subject> > >I had same problem, was Cisco trained. I took some of Enterasys's >bootcamps. They are very helpful. GTAC is helpful too. > > >Jeremiah Pluim, Network Administrator II Avery Weigh-Tronix LLC > > >-----Original Message----- >From: Jason Grubbs [mailto:[email protected]] >Sent: Tuesday, October 25, 2011 2:10 PM >To: Enterasys Customer Mailing List >Subject: Re: [enterasys] <no subject> > >I am having trouble getting them configured at all. The commands are >very different than on Cisco switches. > >I know I have to create all of the vlans on the Enterasys switches >because they don't recognize VTP but I am not having any luck. > >Jason Grubbs >Network Engineer >Pottsgrove School District > >From: "Borel, Reese" ><[email protected]<mailto:[email protected]><mailto:[email protected]>> >Reply-To: >"[email protected]<mailto:[email protected]><mailto:ente >[email protected]>" ><[email protected]<mailto:[email protected]><mailto:ente >[email protected]>> >Date: Tue, 25 Oct 2011 14:52:15 -0400 >To: Enterasys Customer Mailing List ><[email protected]<mailto:[email protected]><mailto:ente >[email protected]>> >Subject: RE:[enterasys] <no subject> > >What is the problem you are having? We have Enterasys to Cisco back to >Enterasys and vice versa... Sending trunked vlans both directions. > >Thanks, >Reese > >-----Original Message----- >From: Jason Grubbs [mailto:[email protected]] >Sent: Tuesday, October 25, 2011 1:47 PM >To: Enterasys Customer Mailing List >Subject: [enterasys] <no subject> > >Hello All, > >Until now, we have been a Cisco network. We recently purchased Enterasys >switches and I am having trouble getting them connected to our Cisco >network. Does anyone have any experience adding Enterasys switches to a >Cisco network? > > >________________________________ >This email and any files transmitted with it are to be treated as >confidential and as such are not to be used or disclosed except for the >purpose for which it has been sent. Any views or opinions presented in >this e-mail are solely those of the author and do not represent those of >the Pottsgrove School District. The School District accepts no liability >for any damage caused by this e-mail. The recipient is required to >indemnify the School District against any claims for loss or damage >caused by any viruses or otherwise. > >--- >To unsubscribe from enterasys, send email to >[email protected]<mailto:[email protected]><mailto:[email protected]> with >the body: unsubscribe enterasys >[email protected]<mailto:[email protected]><mailto:[email protected]> > > >--- >To unsubscribe from enterasys, send email to >[email protected]<mailto:[email protected]><mailto:[email protected]> with >the body: unsubscribe enterasys >[email protected]<mailto:[email protected]><mailto:[email protected]> > > >--- >To unsubscribe from enterasys, send email to >[email protected]<mailto:[email protected]> with the >body: unsubscribe enterasys >[email protected]<mailto:[email protected]> > >--- >To unsubscribe from enterasys, send email to >[email protected]<mailto:[email protected]> with the body: unsubscribe >enterasys >[email protected]<mailto:[email protected]> > > >--- >To unsubscribe from enterasys, send email to >[email protected]<mailto:[email protected]> with the body: unsubscribe >enterasys [email protected]<mailto:[email protected]> > > >--- >To unsubscribe from enterasys, send email to [email protected] with the >body: unsubscribe enterasys [email protected] > > > >--- >To unsubscribe from enterasys, send email to [email protected] with the >body: unsubscribe enterasys [email protected] --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected]
