Dave,
I'm not sure what you're trying to accomplish. The problem isn't a
software mismatch, the problem is that the slot was configured for a
different linecard than has been inserted. That cannot be amended by
explicitly configuring boot defaults and typing a few syntactically
invalid commands.
-- Niels.
* [email protected] (Dave Peters) [Tue 09 Nov 2010, 18:29 CET]:
You can try:
lp boot system mp primary
then
power-off lp primary [slot #]
power-on lp primary [slot#]
If that doesn't work, you may want to try loading the compatible software train
onto the interactive card, so it matches the management module.
--Dave Peters
________________________________________
From: [email protected] [[email protected]]
On Behalf Of Remco Bressers [[email protected]]
Sent: Tuesday, November 09, 2010 8:44 AM
To: [email protected]
Subject: Re: [f-nsp] Not able to use XMR 10 gig linecard
We didn't physically remove the module yet (it's 150KM away) so i hoped
there was a different way of doing it.
The boot procedure on the LP is pretty non-explanatory :
tel...@r#lp boot system mp pri 2
tel...@r#rconsole 2
Remote connection to LP slot 2 established
Press CTRL-X or type 'exit' to disconnect it
NetIron XMR/MLX Boot Monitor Version 3.5.00e
Enter 'b' to stop at boot monitor
sent IPC_MSGTYPE_REBOOT to slot 16 (my_slot = 1, ipc_post_rx32_mode = 0)
received IPC_MSGTYPE_REBOOT_ACK from fid d020
REV B LP
get_moass = cf 207 20
ipc_sedule_type: board_clnd_card_boot: module_type = 20
REV B LP
get_module_type: board_class = cf 207 20
PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xgmac_arg = 0,
hv_cam_type = ff, hv_value = 0
sent IPC_MSGTYPE_LP_CARD_BOOT to slot 32
Received IPC_MSGTYPE_MP_CARD_BOOT_INFO
g_bp_board_class_val = 0x86, g_rx16_backplane_type = 255
BOOT INFO: boot interactively
REV B LP
get_module_type: board_class = cf 207 20
REV B LP
get_module_type: board_class = cf 207 20
PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xbridge_arg = 0,
xgmac_arg = 0, hv_cam_type = ff, hv_value = 0
sent IPC_MSGTYPE_LP_CARD_SW_LOADED (failed) to slot 32
So i think we have to physically eject the module :(
Regards,
Remco
On 11/09/2010 05:41 PM, Jared Valentine wrote:
Sounds like you need to:
1.) physically remove module
2.) remove slot configuration using "no module xxx"
3.) pre-stage the config with the new module "module xxx"
3.) physically replace module
4.) deal with the software issue
-Jared
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Remco Bressers
Sent: Tuesday, November 09, 2010 9:16 AM
To: [email protected]
Subject: Re: [f-nsp] Not able to use XMR 10 gig linecard
Unfortunately that won't work because of the same reason :
tel...@ams-er8-sara(config)#no module 2 ni-xmr-20-port-1g
Error: Please remove module from slot 2 first
Also, powering off the card won't do.
:(
Regards,
Remco
On 11/09/2010 05:12 PM, Michiel Muhlenbaumer wrote:
First run 'no module blabla' and then power-off/on the lc.
Met vriendelijke groet,
Best regards,
Michiel Muhlenbaumer
Atrato IP Networks
(sent from mobile device)
On 9 nov. 2010, at 16:58, Remco Bressers <[email protected]> wrote:
Hi,
The other day, i inserted a brand new NI-XMR-10Gx4 in an XMR-4, but it
won't work correctly.
If i do a "show module", i see the following output on the slot :
S2: NI-XMR-10Gx4 4-port 10GbE Module CARD_STATE_INTERACTIVE 20
0012.f2f5.d128
(S2: Configured as NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module)
What is the correct procedure to configure S2 as ni-xmr-10gx4 ?
I tried :
tel...@r(config)#module 2 ni-xmr-4-port-10g
Error: Please remove module from slot 2 first
tel...@r(config)#
Is this the only (and correct) way?
--
Kind regards,
Signet bv
Remco Bressers
--
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
