I think you need to supply a bit more information about what exactly you are doing, and/or expecting to happen. I notice you have a VERIFY(FC1800) on your INIT. So, the FC1800 volser was originally NONSMS? You then re-initialise as SMS, with the same volser? You then add it into a Storage Group, and activate the new SMS config? Or is it already pre-defined to a storage group? What does a D SMS,VOL(FC1800) show?
On 4 August 2014 19:55, Lizette Koehler <[email protected]> wrote: > So are all volumes ENABLED? > > Just because you DISPLAY doesn't tell me their state. > > Lizette > > > -----Original Message----- > >From: Rajesh Janakiraman <[email protected]> > >Sent: Aug 4, 2014 10:28 AM > >To: [email protected] > >Subject: Re: Initialization problem in Storage Group > > > >Hi Lizette, > > > >All the volumes are displayed in pool. > > > > > >On Mon, Aug 4, 2014 at 8:25 AM, Lizette Koehler <[email protected]> > >wrote: > > > >> How does the storage group look in ISMF? Are any volumes DISNEW, > DISABLE, > >> QUINEW? > >> > >> How did you determine the are not in the pool or not being used in the > >> pool? > >> > >> It sounds like some of your volumes may not be in the pool the way you > >> think they should be. > >> > >> Do you have Chicago Soft QuickREF? It has a very nice Space display in > it. > >> > >> It might be quicker to raise an SR with IBM for assistance. We cannot > see > >> what things look like at your shop. > >> > >> > >> Lizette > >> > >> > -----Original Message----- > >> > From: IBM Mainframe Discussion List [mailto:[email protected]] > On > >> > Behalf Of Rajesh Janakiraman > >> > Sent: Sunday, August 03, 2014 7:42 PM > >> > To: [email protected] > >> > Subject: Re: Initialization problem in Storage Group > >> > > >> > Hi Lizette, > >> > All those volumes are already online. > >> > And yes we are doing those steps which you have mentioned > >> > > >> > > >> > On Mon, Aug 4, 2014 at 7:40 AM, Lizette Koehler < > [email protected] > >> > > >> > wrote: > >> > > >> > > I am not sure I understand. > >> > > > >> > > When you initialize a volume for an SMS Managed pool the ICKDSF > >> > > control cards need SG/STGR/STORAGEGROUP. > >> > > > >> > > Vary it online. > >> > > > >> > > Then you go to ISMF (my preference) and add the volume to the pool. > >> > > > >> > > Then you enable the volume or activate the SMS configuration to > bring > >> > > it into the pool. > >> > > > >> > > If you have place holder SMS Volume names for that pool, I think you > >> > > can just enable the volume. Otherwise I think you have to do an > >> ACTIVATE. > >> > > > >> > > Are you doing all of those steps? > >> > > > >> > > > >> > > Lizette > >> > > > >> > > > >> > > > >> > > > >> > > > -----Original Message----- > >> > > > From: IBM Mainframe Discussion List > >> > > > [mailto:[email protected]] On Behalf Of Rajesh Janakiraman > >> > > > Sent: Sunday, August 03, 2014 6:05 PM > >> > > > To: [email protected] > >> > > > Subject: Initialization problem in Storage Group > >> > > > > >> > > > Hi Mates, > >> > > > > >> > > > Our production system Storage Group initialization is not getting > >> > > initialized > >> > > > completely. > >> > > > > >> > > > Whenever we initialize the storage group by submitting jobs it is > >> > > > not > >> > > getting initialized > >> > > > completely, for eg. before initialization if the storage group % > >> > > > free > >> > > space is 52%, > >> > > > then same is shown after initialization. > >> > > > > >> > > > The initialization job contains following commands, below command > is > >> > > > for > >> > > one > >> > > > volume > >> > > > > >> > > > /*$VS, 'RO *ALL,V 1800,OFFLINE' > >> > > > > >> > > > INIT UNITADDRESS(1800) DEVICETYPE(3390) - > >> > > > VOLID(FC1800) INDEX(15,0,045) VTOC(0,1,224) - PURGE MAP NOCHECK > >> > > > STGR VERIFY(FC1800) > >> > > > > >> > > > /*$VS, 'RO *ALL,V 1800,ONLINE' > >> > > > > >> > > > There are total of 1200 volumes. > >> > > > > >> > > > Kindly provide a solution that to get the storage group > initialized > >> > > completely. > >> > > > > >> > > > > >> > > > Thanks & Regards, > >> > > > Rajesh Janakiraman > >> > > > Mainframe System Analyst > >> > > > > >> > > > >> > >> ---------------------------------------------------------------------- > >> For IBM-MAIN subscribe / signoff / archive access instructions, > >> send email to [email protected] with the message: INFO IBM-MAIN > >> > > > > > > > >-- > >Regards, > >*Rajesh Janakiraman* > > > >---------------------------------------------------------------------- > >For IBM-MAIN subscribe / signoff / archive access instructions, > >send email to [email protected] with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
