Got such quick responses last time, so now on the phase 2! And yes
phase 3 is profit.
No Audio! I looked through lots of posts in the archives dating back
quite a bit and using 2.x and early 3.x builds and found no answers to
my problem. So here is my info again. I have 2 brand new PVR-150 MCE
installed to my backend. Video is now working wonderfully with Myth
0.18.1 and via cat /dev/video tests, now onto the audio! And as
suggested I'm now up to build k. MythTV and mpegs directly cat'd
contain no audio.
[EMAIL PROTECTED] incoming]# cat /dev/video0 >> test.mpg
[EMAIL PROTECTED] incoming]# tcprobe -i test.mpg
[tcprobe] MPEG program stream (PS)
[tcprobe] summary for test.mpg, (*) = not default, 0 = not detected
import frame size: -g 720x480 [720x576] (*)
aspect ratio: 4:3 (*)
frame rate: -f 29.970 [25.000] frc=4 (*)
PTS=0.4004, frame_time=33 ms, bitrate=9600 kbps
audio track: -a 0 [0] -e 48000,16,2 [48000,16,2] -n 0x50 [0x2000] (*)
PTS=0.3338, bitrate=384 kbps
-D 1 --av_fine_ms 33 (frames & ms) [0] [0]
[EMAIL PROTECTED] incoming]#
It's got an audio track, just nothing on it. I assume this has been
discussed before, but I found nothing in the archives or faqs to help.
Nothing in modprobe.conf for ivtv as suggested, and just 'ivtv' in
modprobe.preload.
Firmware files extracted from CD-ROM except ivtv-fw-dec.bin which i got
from the recommended firmware file to acheive encoder version 0x02040011
that it was whining about.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.7 (k) loading
ivtv: Linux version: 2.6.11-6mdk 686 gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
PCI: Found IRQ 10 for device 0000:02:0b.0
PCI: Sharing IRQ 10 with 0000:00:1f.4
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 7969385
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840: firmware /lib/modules/HcwMakoA.ROM loaded
ivtv: i2c attach to card #0 ok [client=cx25840[50], addr=44]
ivtv: i2c attach to card #0 ok [client=wm8775[50], addr=1b]
ivtv: Encoder revision: 0x02040011
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Create encoder radio stream
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: Initialized WinTV PVR 150, card #0
ivtv: ====================== NEXT CARD ======================
ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
PCI: Found IRQ 9 for device 0000:02:0c.0
PCI: Sharing IRQ 9 with 0000:00:1f.3
PCI: Sharing IRQ 9 with 0000:00:1f.5
PCI: Sharing IRQ 9 with 0000:02:0e.0
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8402116
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv: i2c attach to card #1 ok [client=tveeprom[50], addr=50]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=61]
cx25840: firmware /lib/modules/HcwMakoA.ROM loaded
ivtv: i2c attach to card #1 ok [client=cx25840[50], addr=44]
ivtv: i2c attach to card #1 ok [client=wm8775[50], addr=1b]
ivtv: Encoder revision: 0x02040011
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
ivtv: Create encoder radio stream
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
Note the 2 sound cards are present from when I had 2 bt8x8 cards being
used in my mythbox, in case you were confused.
==================== START LSPCI ====================
00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset
Host Bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [0104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP
Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc900000-fe9fffff
Prefetchable memory behind bridge: e0600000-e46fffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 12) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: e4700000-f47fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 12)
(prog-if 80 [Master])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev
12) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 3
Region 4: I/O ports at ef40 [size=32]
00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 12)
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at efa0 [size=16]
00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev
12) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 4: I/O ports at ef80 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97
Audio (rev 12)
Subsystem: Intel Corporation: Unknown device 6876
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ef00 [size=64]
01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta/Vanta
LT] (rev 15) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 0004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e2000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at fe9f0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM
Ethernet Controller (rev 03)
Subsystem: Intel Corporation EtherExpress PRO/100 VE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at df00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs: Unknown device 8032
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at df80 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
(rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at dff0 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0b.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 8801
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), cache line size 04
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0c.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 8801
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.0 Ethernet controller: Linksys NC100 Network Everywhere Fast
Ethernet 10/100 (rev 11)
Subsystem: Linksys: Unknown device 0574
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min, 63750ns max), cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at feafec00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
==================== END LSPCI ====================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
_______________________________________________
ivtv-devel mailing list
ivtv-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
