> Please stick to kernel 2.6.16 and ivtv-0.6. Later versions will only > confuse matters. I do recommend using the ivtv-0.6 development snapshot > (http://ivtvdriver.org/viewcvs/ivtv/branches/0.6.tar.gz?view=tar) as it > has the 'newi2c=0' module option. > > Once you have installed this then let me know the results using newi2c=0 > and newi2c=1 (no other options or debug flags) and we'll take it from > there. > > Hans
ok. Built a new 2.6.16.18 kernel from the tarball and installed the 0.6 based on the link you sent above. modprobe ivtv newi2c=0 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 22 tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: tuner type not set tuner 1-0061: tuner type not set ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv0: Removed Hauppauge WinTV PVR-150, card #0 modprobe ivtv newi2c=1 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 22 tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: tuner type not set tuner 1-0061: tuner type not set ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== reboot (I have ivtv 'blacklisted' for udev, so it won't load automatically) modprobe ivtv newi2c=0 Linux video capture interface: v1.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: tuner type not set tuner 1-0061: tuner type not set ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== rmmod ivtv cx25840 tuner tveeprom wm8775 tda9887 modprobe ivtv newi2c=1 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21 tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: tuner type not set tuner 1-0061: tuner type not set ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== so, ok so far. Try a power cycle: nvram-wakeup --directisa -s $((`date +%s` + 600)) poweroff modprobe ivtv newi2c=0 -takes 10 minutes to come back ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21 tveeprom 1-0050: Huh, no eeprom present (err=-121)? tveeprom 1-0050: Encountered bad packet header [20]. Corrupt or not a Hauppauge eeprom. ivtv0: No tuner detected, default to NTSC ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0xc0045627! ivtv0: i2c hardware 0x00000020 not found for command 0x40345622! ivtv0: i2c addr 0x44 not found for command 0x40345622! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv 168720 0 ivtv 168720 0 tveeprom 14096 1 ivtv i2c_algo_bit 8584 1 ivtv v4l1_compat 12164 1 ivtv videodev 9600 1 ivtv i2c_core 20736 8 wm8775,cx25840,tda9887,tuner,ivtv,tveeprom,i2c_algo_bit,i2c_viapro rmmod ivtv cx25840 tuner tveeprom wm8775 tda9887 modprobe ivtv newi2c=1 -came back instantly ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Thu 08 Jun 2006 12:24:13 AM PDT) loading ivtv: Linux version: 2.6.16.18 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 21 tveeprom 1-0050: Huh, no eeprom present (err=-121)? tveeprom 1-0050: Encountered bad packet header [20]. Corrupt or not a Hauppauge eeprom. ivtv0: No tuner detected, default to NTSC ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0xc0045627! ivtv0: i2c hardware 0x00000020 not found for command 0x40345622! ivtv0: i2c addr 0x44 not found for command 0x40345622! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== rmmod ivtv cx25840 tuner tveeprom wm8775 tda9887 modprobe ivtv newi2c=1 ivtv_debug=33 dmesg was full, but I did get this much: ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 6c failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 6d failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 6e failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 6f failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 42 failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 43 failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 4b failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 44 failed ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: SDA was low at start ivtv0 i2c: SDA stuck low ivtv0 i2c: SCL could not be set high ivtv0 i2c: i2c write to 1b failed ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0xc0045627! ivtv0: i2c hardware 0x00000020 not found for command 0x40345622! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0x40345622! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0 i2c: call_i2c_client addr=44 ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== So, what do you think Hans? _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
