Hi, Here is demovideo about via stitching. It is slowly, because of slowly machine. I do some development too, so full patch is attached too.
On Tue, Oct 11, 2016 at 5:49 PM, Marcos Chaparro <[email protected]> wrote: > Hi Heikki, > is there any chance to make some screenshots or video about this? Some of > us do compile kicad to get the latest and greatest but never applied a > patch for a particular feature. > > Regards > > > Marcos > > On Sat, Oct 8, 2016 at 7:04 AM, Heikki Pulkkinen <[email protected]> > wrote: > >> Hi, >> >> Putting back that my via stitching tool to routing tool. It is better >> that way, I think. All via tools are in same place, and it adds vias to >> pours only from hotkeys. >> >> >> >> On Sun, Oct 2, 2016 at 12:28 PM, Heikki Pulkkinen <[email protected]> >> wrote: >> >>> Hi, >>> >>> Finally Via Stitching without tracks is at zone tool. I tested it little >>> bit, but more tests are needed. This patch replace all other patches. Do >>> not use them, use only this patch. I think this is worth of try. I am going >>> to use it anyway, even if it do not get any acceptance. First patch is for >>> Fedora users. It makes possible to build Kicad in Fedora release wxWidgets >>> libs whitout building wxWidget from source. I do not know has anybody else >>> that problem, but I had. >>> >>> >>> Heikki >>> >>> On Tue, Sep 27, 2016 at 6:46 PM, Heikki Pulkkinen <[email protected]> >>> wrote: >>> >>>> Hi >>>> >>>> And I really practice. I made improvement and forgot to copy all. So >>>> improvement is in these two patches. I hope this suggestion is accepted as >>>> a new feature. >>>> >>>> Heikki >>>> >>>> On Tue, Sep 27, 2016 at 2:31 PM, Heikki Pulkkinen <[email protected]> >>>> wrote: >>>> >>>>> Hi, >>>>> >>>>> As in practice, I made a patch file of my changes Not only diifs. It >>>>> is SHIFT-ALT-V hotkey whitch make buried and blind vias, as it is in >>>>> routing too. >>>>> >>>>> >>>>> Heikki >>>>> >>>>> On Sun, Sep 25, 2016 at 2:25 PM, Heikki Pulkkinen <[email protected]> >>>>> wrote: >>>>> >>>>>> Hi, >>>>>> >>>>>> I made some improvements to my patch of via stitching. Now you can >>>>>> just point copper pour place and press V, it make trough via. If you >>>>>> press >>>>>> SHIFT+CTRL+V it make buried or blind via.It does not change working >>>>>> layer. >>>>>> Only when you place buried or blind via from different layer than it's >>>>>> layer pair is. I think that it is quite easy to shoot board full of >>>>>> copper >>>>>> pours connecting vias. It is possible to remove connecting tracks from >>>>>> old >>>>>> designs. Just delete connection from pad and use clenup. Only have to >>>>>> remember that if there are not at least two copper pours in same netcode >>>>>> in >>>>>> different layers via is deleted too. Any support? >>>>>> >>>>>> >>>>>> Heikki >>>>>> >>>>>> On Sat, Sep 24, 2016 at 3:06 PM, Heikki Pulkkinen <[email protected] >>>>>> > wrote: >>>>>> >>>>>>> Hi everybody, >>>>>>> >>>>>>> This is my suggestion to via stitching without any tracks. It >>>>>>> connects unconnected vias in different copper pours witch has same >>>>>>> netcode. >>>>>>> Adding vias is normal routing process without routing tracks. Start - >>>>>>> Change Layer - End. Tool that do those things automatically would be >>>>>>> good, >>>>>>> so you can add all vias in same layer. After adding vias, run "Fill or >>>>>>> Refill All Zones" that "Clenup tracks and vias" do not remove partly >>>>>>> connected vias. >>>>>>> >>>>>>> >>>>>>> Heikki >>>>>>> >>>>>> >>>>>> >>>>> >>>> >>> >> >> _______________________________________________ >> Mailing list: https://launchpad.net/~kicad-developers >> Post to : [email protected] >> Unsubscribe : https://launchpad.net/~kicad-developers >> More help : https://help.launchpad.net/ListHelp >> >> >
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : [email protected] Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
