Hi Lionel,
Does the entire system hang, or only your dos session hangs ? I could
never successfully load a PCI ethernet Card driver under dosemu, as the
entire system was hanging. As I did not have much time to debug, I've
currently opted for an ISA NIC, which works fine.
Are you sure that the IO & IRQ are free at the OS level ? ie. you should
not have loaded any drivers in Linux (if ur using Linux !) before you
tried in dosemu. (cat /proc/interrupts & cat /proc/ioports - Ur IO & IRQ
should not appear here.)
One option would be is to enable debugging (Start dos as dos -H1 -o
debugfile) & then launch dosdebug on another session, type 'log +a' ENTER
& then g <ENTER>. In another session watch the debugfile, as it grows &
see whether the driver is in a loop !
May be you'll find some clues from the dbg. output !
Sreeji
On 13 Sep 2001, Lionel DARNIS wrote:
> Dear Sreeji,
>
> Since I put $_pci = (on) and $_irqpassing the dosemu block when I load
> the driver of the Network card.
> An Idea ?
> About the point 3, the card work fine under msdos
>
> Lionel
>
> > Hi
> >
> > Did you :
> > 1) Enable PCI in dosemu.conf ie. $_pci = (on)
> > 2) Pass the IO range & IRQ of the card using the $_ports (Eg. $_ports =
> > "range 0x1000,0x10FF") & $_irqpassing (Eg. $_irqpassing = "11")
> > 3) Try loading the driver in MSDOS & did it load properly ?
> >
> > Most likely (1) might solve your problem.
> >
> > Sreeji
> >
> > On 12 Sep 2001, Lionel DARNIS wrote:
> >
> > >
> > > Hi,
> > >
> > > Always with my dosemu 1.0.2 and A D-Link network card.
> > > In my dosemu.conf :
> > >
> > > $_ipxsupport = (on)
> > > $_novell_hack = (on)
> > > $_vnet = (on)
> > >
> > > I try to use a netware client ( NETX with lsl ...) and I don't arrive to
> > > load the driver of the network card : DLINK, and I obtain this result
> > > whan I try to launch the driver of the card after the lauch of lsl.exe
> > >
> > > C:\NWCLIENT>dlkfet
> > > D-Link DFE-530TX PCI Fast Ethernet Adapter MLID v2.39 (990119)
> > > Copyright D-Link Corporation 1999. All right reserved.
> > >
> > > Slot 255, IRQ 5, Port 300
> > > Max Frame 1514 bytes, Line Speed 10 Mbps, Half-Duplex
> > > Board 1, Frame ETHERNET_802.3, LSB Mode
> > >
> > > FATAL: VT86C100A Does not support this bus type
> > >
> > > DLKFET-DOS-6: The adapter did not initialize. DLKFET did not load.
> > >
> > > Could you help me, PLEASE !!!
> > >
> > > Regards.
> > >
> > > Lionel DARNIS
> > >
> > >
> > >
> > > -
> > > To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
> > > the body of a message to [EMAIL PROTECTED]
> > > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > >
>
-
To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
