Dear Sreeji,
If I understood all you explain me I can't use the same NIC for Linux
and Dosemu ?!
Because My PCI NIC is ON IRQ 10 and range B400-B47F under Linux and I
use the same under Dosemu. About you question, the entire system not
hang it is only the dos session.
But always this story for the use of NIC with Linux and Dosemu, do you
think I need two network cards : one for the dsl/local network access
under linux and on for dosemu/novell access ?
Thanx a lot for your help.
Regards,
Lionel
:
> Hi Lionel,
>
> Does the entire system hang, or only your dos session hangs ? I could
> never successfully load a PCI ethernet Card driver under dosemu, as the
> entire system was hanging. As I did not have much time to debug, I've
> currently opted for an ISA NIC, which works fine.
>
> Are you sure that the IO & IRQ are free at the OS level ? ie. you should
> not have loaded any drivers in Linux (if ur using Linux !) before you
> tried in dosemu. (cat /proc/interrupts & cat /proc/ioports - Ur IO & IRQ
> should not appear here.)
>
> One option would be is to enable debugging (Start dos as dos -H1 -o
> debugfile) & then launch dosdebug on another session, type 'log +a' ENTER
> & then g <ENTER>. In another session watch the debugfile, as it grows &
> see whether the driver is in a loop !
>
> May be you'll find some clues from the dbg. output !
>
> Sreeji
> On 13 Sep 2001, Lionel DARNIS wrote:
>
> > Dear Sreeji,
> >
> > Since I put $_pci = (on) and $_irqpassing the dosemu block when I load
> > the driver of the Network card.
> > An Idea ?
> > About the point 3, the card work fine under msdos
> >
> > Lionel
> >
> > > Hi
> > >
> > > Did you :
> > > 1) Enable PCI in dosemu.conf ie. $_pci = (on)
> > > 2) Pass the IO range & IRQ of the card using the $_ports (Eg. $_ports =
> > > "range 0x1000,0x10FF") & $_irqpassing (Eg. $_irqpassing = "11")
> > > 3) Try loading the driver in MSDOS & did it load properly ?
> > >
> > > Most likely (1) might solve your problem.
> > >
> > > Sreeji
> > >
> > > On 12 Sep 2001, Lionel DARNIS wrote:
> > >
> > > >
> > > > Hi,
> > > >
> > > > Always with my dosemu 1.0.2 and A D-Link network card.
> > > > In my dosemu.conf :
> > > >
> > > > $_ipxsupport = (on)
> > > > $_novell_hack = (on)
> > > > $_vnet = (on)
> > > >
> > > > I try to use a netware client ( NETX with lsl ...) and I don't arrive to
> > > > load the driver of the network card : DLINK, and I obtain this result
> > > > whan I try to launch the driver of the card after the lauch of lsl.exe
> > > >
> > > > C:\NWCLIENT>dlkfet
> > > > D-Link DFE-530TX PCI Fast Ethernet Adapter MLID v2.39 (990119)
> > > > Copyright D-Link Corporation 1999. All right reserved.
> > > >
> > > > Slot 255, IRQ 5, Port 300
> > > > Max Frame 1514 bytes, Line Speed 10 Mbps, Half-Duplex
> > > > Board 1, Frame ETHERNET_802.3, LSB Mode
> > > >
> > > > FATAL: VT86C100A Does not support this bus type
> > > >
> > > > DLKFET-DOS-6: The adapter did not initialize. DLKFET did not load.
> > > >
> > > > Could you help me, PLEASE !!!
> > > >
> > > > Regards.
> > > >
> > > > Lionel DARNIS
> > > >
> > > >
> > > >
> > > > -
> > > > To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
> > > > the body of a message to [EMAIL PROTECTED]
> > > > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > > >
> >
-
To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
