OK Sreeji,
But the fact is I use the card without the linux module loaded and I use
dosemu with the dos driver and it do the same the dosemu session hang.
I tried to found an 3COM ISA Card to test.
I take you inform.
thanx
Lionel
>
> Hi Lionel
>
> Yup. The NIC that you are going to use in DOSEMU *must* be exclusively
> dedicted for DOSEMU. The driver you are loading is a DOS driver, which
> would have been written with DOS in mind, thus having all powers to
> directly access the hw. So you cannot have a single card with both Linux &
> DOS drivers loaded at the same time :(. You'd most likely freeze your
> system (may be when you try to do a ping or so !)
>
> Sreeji
>
> On 13 Sep 2001, Lionel DARNIS wrote:
> > Dear Sreeji,
> >
> > If I understood all you explain me I can't use the same NIC for Linux
> > and Dosemu ?!
> > Because My PCI NIC is ON IRQ 10 and range B400-B47F under Linux and I
> > use the same under Dosemu. About you question, the entire system not
> > hang it is only the dos session.
> > But always this story for the use of NIC with Linux and Dosemu, do you
> > think I need two network cards : one for the dsl/local network access
> > under linux and on for dosemu/novell access ?
> >
> > Thanx a lot for your help.
> >
> > Regards,
> >
> > Lionel
> >
> > :
> > > Hi Lionel,
> > >
> > > Does the entire system hang, or only your dos session hangs ? I could
> > > never successfully load a PCI ethernet Card driver under dosemu, as the
> > > entire system was hanging. As I did not have much time to debug, I've
> > > currently opted for an ISA NIC, which works fine.
> > >
> > > Are you sure that the IO & IRQ are free at the OS level ? ie. you should
> > > not have loaded any drivers in Linux (if ur using Linux !) before you
> > > tried in dosemu. (cat /proc/interrupts & cat /proc/ioports - Ur IO & IRQ
> > > should not appear here.)
> > >
> > > One option would be is to enable debugging (Start dos as dos -H1 -o
> > > debugfile) & then launch dosdebug on another session, type 'log +a' ENTER
> > > & then g <ENTER>. In another session watch the debugfile, as it grows &
> > > see whether the driver is in a loop !
> > >
> > > May be you'll find some clues from the dbg. output !
> > >
> > > Sreeji
> > > On 13 Sep 2001, Lionel DARNIS wrote:
> > >
> > > > Dear Sreeji,
> > > >
> > > > Since I put $_pci = (on) and $_irqpassing the dosemu block when I load
> > > > the driver of the Network card.
> > > > An Idea ?
> > > > About the point 3, the card work fine under msdos
> > > >
> > > > Lionel
> > > >
> > > > > Hi
> > > > >
> > > > > Did you :
> > > > > 1) Enable PCI in dosemu.conf ie. $_pci = (on)
> > > > > 2) Pass the IO range & IRQ of the card using the $_ports (Eg. $_ports =
> > > > > "range 0x1000,0x10FF") & $_irqpassing (Eg. $_irqpassing = "11")
> > > > > 3) Try loading the driver in MSDOS & did it load properly ?
> > > > >
> > > > > Most likely (1) might solve your problem.
> > > > >
> > > > > Sreeji
> > > > >
> > > > > On 12 Sep 2001, Lionel DARNIS wrote:
> > > > >
> > > > > >
> > > > > > Hi,
> > > > > >
> > > > > > Always with my dosemu 1.0.2 and A D-Link network card.
> > > > > > In my dosemu.conf :
> > > > > >
> > > > > > $_ipxsupport = (on)
> > > > > > $_novell_hack = (on)
> > > > > > $_vnet = (on)
> > > > > >
> > > > > > I try to use a netware client ( NETX with lsl ...) and I don't arrive to
> > > > > > load the driver of the network card : DLINK, and I obtain this result
> > > > > > whan I try to launch the driver of the card after the lauch of lsl.exe
> > > > > >
> > > > > > C:\NWCLIENT>dlkfet
> > > > > > D-Link DFE-530TX PCI Fast Ethernet Adapter MLID v2.39 (990119)
> > > > > > Copyright D-Link Corporation 1999. All right reserved.
> > > > > >
> > > > > > Slot 255, IRQ 5, Port 300
> > > > > > Max Frame 1514 bytes, Line Speed 10 Mbps, Half-Duplex
> > > > > > Board 1, Frame ETHERNET_802.3, LSB Mode
> > > > > >
> > > > > > FATAL: VT86C100A Does not support this bus type
> > > > > >
> > > > > > DLKFET-DOS-6: The adapter did not initialize. DLKFET did not load.
> > > > > >
> > > > > > Could you help me, PLEASE !!!
> > > > > >
> > > > > > Regards.
> > > > > >
> > > > > > Lionel DARNIS
> > > > > >
> > > > > >
> > > > > >
> > > > > > -
> > > > > > To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
> > > > > > the body of a message to [EMAIL PROTECTED]
> > > > > > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > > > > >
> > > >
> >
>
-
To unsubscribe from this list: send the line "unsubscribe linux-msdos" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
