Re: [Machinekit] Cannot find ethernet ip adress of Beaglebone Black

[schoone...@btinternet.com]

On 12/02/17 16:11, Sag ich Dir nich wrote: Thank you, ill try that usb0 is (i believe) the emulated network over usb (so you can communicate with the beaglebone with the ip 192.168.7.2) and can you (communicate with the beaglebone with the ip 192.168.7.2) ? I would suspect that this USB connection is what is causing the problem and the inet6 addr is a link-local one from the one shown under USB0. Why do you not just plug in an ethernet cable from your router? I have always either used something like Cutecom and a USB jtag cable or just plain ethernet connection and ssh to do headless connection. I don't however have a BBB, so if this is something specific to it, hopefully someone else will chime in Am Sonntag, 12. Februar 2017 16:15:54 UTC+1 schrieb Schooner: On 12/02/17 14:15, Sag ich Dir nich wrote: I need to know the ip adress of my beaglebone so i can connect it to my pc via ssh but when i write ifconfig in the terminal i get no ethernet ip adress: machinekit@beaglebone:~$ ifconfig eth0      Link encap:Ethernet  HWaddr a0:f6:fd:4b:9c:97             inet6 addr: fe80::a2f6:fdff:fe4b:9c97/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:316 errors:0 dropped:0 overruns:0 frame:0           TX packets:51 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:77089 (75.2 KiB)  TX bytes:13100 (12.7 KiB)           Interrupt:40  lo        Link encap:Local Loopback             inet addr:127.0.0.1  Mask:255.0.0.0           inet6 addr: ::1/128 Scope:Host           UP LOOPBACK RUNNING  MTU:65536  Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:0            RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) What is usb0?  Is this a USB modem or similar? usb0      Link encap:Ethernet  HWaddr a0:f6:fd:4b:9c:99             inet addr:192.168.7.2  Bcast:192.168.7.3  Mask:255.255.255.252           UP BROADCAST MULTICAST  MTU:1500  Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) You may need to disable ipv6 to get ipv4 ip addresses eg http://raspberrypi.stackexchange.com/questions/23884/force-ipv4-address do i have to install something? -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to machinekit+...@googlegroups.com. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout. -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to machinekit+unsubscr...@googlegroups.com. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout. -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to machinekit+unsubscr...@googlegroups.com. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.