yes i can communicate with the BBB over usb but the problem with usb is, i can not transfer video over it, so i have to use ethernet but in order to connect through ethernet, i have to know the ip adress (the reason i want to get video over ethernet is i need more i/o pins so i can disable hdmi and use those pins in theory) i want to connect the BBB straight to my pc
Am Sonntag, 12. Februar 2017 17:53:22 UTC+1 schrieb Schooner: > > > On 12/02/17 16:11, Sag ich Dir nich wrote: > > Thank you, ill try that > > usb0 is (i believe) the emulated network over usb (so you can communicate > with the beaglebone with the ip 192.168.7.2) > > > and can you (communicate with the beaglebone with the ip 192.168.7.2) ? > > I would suspect that this USB connection is what is causing the problem > and the inet6 addr is a link-local one from the one shown under USB0. > Why do you not just plug in an ethernet cable from your router? > > I have always either used something like Cutecom and a USB jtag cable or > just plain ethernet connection and ssh > to do headless connection. > > I don't however have a BBB, so if this is something specific to it, > hopefully someone else will chime in > > > Am Sonntag, 12. Februar 2017 16:15:54 UTC+1 schrieb Schooner: >> >> >> On 12/02/17 14:15, Sag ich Dir nich wrote: >> >> I need to know the ip adress of my beaglebone so i can connect it to my >> pc via ssh but when i write ifconfig in the terminal i get no ethernet ip >> adress: >> >> machinekit@beaglebone:~$ ifconfig >> eth0 Link encap:Ethernet HWaddr a0:f6:fd:4b:9c:97 >> inet6 addr: fe80::a2f6:fdff:fe4b:9c97/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:316 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:77089 (75.2 KiB) TX bytes:13100 (12.7 KiB) >> Interrupt:40 >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:65536 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) >> >> What is usb0? Is this a USB modem or similar? >> >> usb0 Link encap:Ethernet HWaddr a0:f6:fd:4b:9c:99 >> inet addr:192.168.7.2 Bcast:192.168.7.3 Mask:255.255.255.252 >> UP BROADCAST MULTICAST MTU:1500 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) >> >> >> You may need to disable ipv6 to get ipv4 ip addresses >> eg >> http://raspberrypi.stackexchange.com/questions/23884/force-ipv4-address >> >> do i have to install something? >> -- >> website: http://www.machinekit.io blog: http://blog.machinekit.io >> github: https://github.com/machinekit >> --- >> You received this message because you are subscribed to the Google Groups >> "Machinekit" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> Visit this group at https://groups.google.com/group/machinekit. >> For more options, visit https://groups.google.com/d/optout. >> >> >> -- > website: http://www.machinekit.io blog: http://blog.machinekit.io github: > https://github.com/machinekit > --- > You received this message because you are subscribed to the Google Groups > "Machinekit" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] <javascript:>. > Visit this group at https://groups.google.com/group/machinekit. > For more options, visit https://groups.google.com/d/optout. > > > -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
