gooday i think there must be sumthing wrong her as ive done all these bolts
and yeah terry i even took the rear leaf off in the end as it wouldnt pull
out properly so i jacked it up pulled on it and the tailshaft started coming
out of the bak of the box, ive tried levering ive tried a lot it appears to
have seized in there is this possible?
thanks again terry and mick
>From: "Mick Ralph" <[EMAIL PROTECTED]>
>Reply-To: [EMAIL PROTECTED]
>To: <[EMAIL PROTECTED]>
>Subject: Re: puzzled
>Date: Sat, 8 Jul 2000 20:06:41 +1000
>
>i usually knock the shims out which allows the front of the diff to go up
>and the back to go down enough to clear the leaf spring...
>sometimes putting in the r180 diff u might have to undo the front bolts of
>the rear x member to chassis to allow the x member to drop a little.. don't
>forget to do em up again before u drive the car tho ...
>cheers
>mick
>
>----- Original Message -----
>From: Terry & Heather <[EMAIL PROTECTED]>
>To: <[EMAIL PROTECTED]>
>Sent: Friday, July 07, 2000 9:06 PM
>Subject: RE: puzzled
>
>
> > Chris,
> > I will give you a check list for the bolts to undo to remove a R160.
> >
> > 1. 4 x tailshaft to front flange
> > 2. 4 x left hand 1/2 shaft to diff flange
> > 3. 4 x right hand 1/2 shaft to diff flange
> > 4. 4 x long bolts at front of diff through x member
> > 5. 2 x bolts holding the rear leaf spring to the body
> >
> > Pull the rear leaf spring which is still attached to the rear cover down
> > until it clears the body mounts and then pull the diff back to slide it
>out.
> > You may have to exert some sideways force to rock it out if the shims
>are
> > stuck in there tightly.
> >
> > that should do it.
> >
> > terry
> >
> > -----Original Message-----
> > From: [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED]]On Behalf Of FJ MAN
> > Sent: Friday, 7 July 2000 5:41 PM
> > To: [EMAIL PROTECTED]; [EMAIL PROTECTED]
> > Subject: puzzled
> >
> >
> > gooday fellas
> > well ive got the diff all unbolted and its ready to come out after the
>whole
> > bolt rouned episode and the other one has been oiled and painted as is
>ready
> > to go in but i cant get the r160 out.
> > where it joins the tailshaft and the front of the diff will not budge so
>i
> > guess im missing sumthing obvious but it will not budge at all and im
>just
> > wondering if any one here could shed sum light it appears to be the only
> > thing stopping it coming out and its very frustrating
> > thanks in advance.
> > chris
> > ________________________________________________________________________
> > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
> >
> >
> >
> >
>
________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.datascribe.com.au/ozdatonline/index.htm
http://www.datascribe.com.au/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
