Zac,
The struts are all the same but remember that the hub heights are different.
I'd be having a very close look at the offset if you have the Girlocks that
take the DB1091 pads before parting with $$$ as the hub height is 4.4 mm
lower than the Japanese and early Girlock.
Terry
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of Zac Campbell
Sent: Thursday, 12 October 2000 3:36 PM
To: [EMAIL PROTECTED]
Subject: Re: hilux calipers and 200b struts
Paddy, all 200B struts are the same, thus the bolt spacing on all is the
same
and so the Hilux calipers should fit any 200B strut!
>
>>From: "Paddy McMillan" <[EMAIL PROTECTED]>
>>Reply-To: [EMAIL PROTECTED]
>>To: <[EMAIL PROTECTED]>
>>Subject: Re: hilux calipers and 200b struts
>>Date: Thu, 12 Oct 2000 03:32:25 +0930
>>
>> Ryan,
>> these had girlock calipers not sumitomo`s, there are two types of
>>girlock
>>caliper one takes the 1091 the other the 1027 pad. the 1027 type is what i
>>fitted the hilux calipers to.
>> I`d say they would fit the ones you speak of aswell as they use the same
>>disc going by the DBA catalog. 253mm diameter as opposed to the 244mm 1091
>>type.
>> I`m not sure if the hilux calipers will fit on the 1091 type or not tho.
>>Paddy
>>
>>----- Original Message -----
>>From: ryan chalmers <[EMAIL PROTECTED]>
>>To: <[EMAIL PROTECTED]>
>>Sent: Thursday, October 12, 2000 7:18 AM
>>Subject: Re: hilux calipers and 200b struts
>>
>>
>> > Paddy,
>> > Were your old calipers the sort that took the squarish pads (sumitomo
>> > calipers) pads part number db86? As I think I will have to look into
>>these
>> > babies.
>> > Ryan
>> >
>> >
>> > >From: "Paddy McMillan" <[EMAIL PROTECTED]>
>> > >Reply-To: [EMAIL PROTECTED]
>> > >To: <[EMAIL PROTECTED]>
>> > >Subject: Re: hilux calipers and 200b struts
>> > >Date: Tue, 10 Oct 2000 19:04:07 +0930
>> > >
>> > > ok i bought the calipers today, and they bolted on to the 200b
>>struts
>> > >and
>> > >fit perfectly over the discs, outer edge of disc just above level with
>> > >outer
>> > >edge of the pad(0.5-1mm), inside edge of pad slightly further towards
>> > >center
>> > >of disc(~5-10mm) than the 200b pads, had to use the hilux bolts as the
>>200b
>> > >were a little short on thread, but that was all. damn easy conversion
>>for
>> > >on
>> > >a 200b, havent fitted the struts to me 510 yet but that will be done
>>the
>> > >next few days.
>> > >the calipers were off an 8/81 hilux 4WD, they have 2 small and 2
larger
>> > >pistons
>> > >the struts were off a 79 200b, 253mm discs not the db1091 pad type
>>ones.
>> > >the struts will need to be swaped on the 510, 13" wheels may JUST fit
>> > >depending on the wheel design, my cheviot hotwires fit over them but
>>only
>> > >just by 1-2mm.
>> > >Paddy
>> > >
>>
>
>_________________________________________________________________________
>Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
>
>Share information about yourself, create your own public profile at
>http://profiles.msn.com.
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
