Re: Window Trouble

[Richard Clough]

Title: Blank

Sorry, I've never had that problem Mark.  If its the winder, you may be best to try another one.  See if you can get a damaged or rusty door and swap the bits.   There may be other models that you can use, or fit new electric winders for "fast glass". ----- Original Message ----- From: Mark O'Conner To: [EMAIL PROTECTED] Sent: Wednesday, 23 October 2002 9:22 AM Subject: Re: Window Trouble Thanks for the reply Richard.   I have tried adjusting the channels but it did nothing. Im thinking its either the pressed pivot pin on the winder arm off the reulator as it has a bit of play OR the pin that fixes the glass to the winder.   Could it be that the regulator is not aligned on the gear teeth correctly?   Im puzzled!   Mark ----- Original Message ----- From: Richard Clough To: [EMAIL PROTECTED] Sent: Tuesday, October 22, 2002 9:40 PM Subject: Re: Window Trouble The window can be adjusted by altering the guide channels in the door.  Loosen the channel screws and slide sideways in the direction opposite to that needed to align the window to the top chanel. The problem of the window dropping may be either a sticky guide channel, due to the mis alignment, or the channel across the base of the glass that the winder is fitted to is loose, and the window "falls" down to reconnect to the winder. (poor description - anyone do a better one?)    ----- Original Message ----- From: Mark O'Conner To: [EMAIL PROTECTED] Sent: Monday, 21 October 2002 9:30 AM Subject: Window Trouble Good morning list,   Hope everyone had a good weekend.   Just wondering if anyone could shed some light on a problem I encountered on the weekend.   I was putting my door windows back into my 1600 - Problem is the drivers door window - when you wind it up it goes crooked and doesn't seem to seal at the top.   When you wind it down, it drops every now and then (only slightly).   Would this be the result of a worn window regulator? -  It seems to be unbalanced to me.   Also, is it normal for the lower edge of the windows where it sits into the channel, when fully up is exposed? I have not yet put the inner or outer weather strips on but it doesn't look lik they will cover it. I site about 5mm above the top of the door.   Sorry for the long message.   Regards   Mark O'Connor   --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ ---------------------------------------------------------------------