did you use new pistons or good used ones?
i want to sand blast mine and then have them coated...good idea? (budget
issues)
who did yours?
how long ago did you do yours and what appx. power level are you at?
did you also stick with stock rings? are you still on this setup? how long
has it lasted with what kind of driving? (track, spirited, auto-x, etc.) sorry
for so many questions, i am about to pull the trigger. Block is being broken
down tonight and ill take it to a shop on monday, as soon as i know the
cylinder wall and crank conditions i will make my final decision.
thank you all
Danijel Krajisnik
[EMAIL PROTECTED] wrote:
I had my stock piston tops ceramic coated and the skirts coated with dry film
lube.
-------------- Original message ----------------------
From: Jason C
> Anything wrong with anti-scuff or anti-friction skirt
> coatings?
> Unneeded?
>
> --- Bill Cardell wrote:
>
> > Are you talking about just coating the crowns? I
> > would think it's worth
> > doing, if done right. I would probably go with
> > factory rings on factory
> > pistons. My 2cents, etc
> >
> >
> > Bill Cardell
> > TurboDog's Dad
> > www.flyinmiata.com
> > www.fmwestfield.com
> > orders 1-800-FLY-MX5S
> > tech support 970-242-3800
> > Don't miss Flyin' Miata's Open House! Aug 14-17,
> > 2008
> >
> >
> >
> > ________________________________
> >
> > From: [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED] On Behalf
> > Of Danijel
> > Krajisnik
> > Sent: Thursday, March 20, 2008 4:48 PM
> > To: [email protected]
> > Subject: Ceramic Coated Stock Pistons
> >
> >
> > Greetings,
> >
> > I know there has been discussion on this in the past
> > but i saw no
> > resolution.
> > Long story short, I have a 94 block (free), H-beam
> > rods (not free), and
> > stock pistons (free)laying around.
> > I was planning a major build but i was pressed for
> > time and need a
> > reliable block NOW.
> > I can't afford Forged Pistons, so i have looked into
> > Ceramic Coating my
> > spare stock ones. By talking with a shop who
> > specializes in ceramic
> > coatings they assure me of all the benefits and
> > mention no negatives
> > whatsoever. I am not looking for the ultimate
> > block, just a stronger
> > than stock one.
> > If i decide to go this route, what rings should i
> > get? I do not mind
> > spending some money on rings since thats what keeps
> > the compression in
> > there. I am not spending a lot of money on this
> > build as i have a
> > friend that built many FE and BP motors helping me
> > put this block
> > together after the machine shop cleans/hones the
> > block and polishes the
> > crank.
> > I pretty much have my mind set on ceramic coating
> > the stock pistons
> > unless someone talks me out of it, all I still need
> > to go through with
> > this is a choice on rings.
> > This block will not see more than 12psi max!!!
> >
> > So, last call on ceramic coated stock pistons and
> > what Rings do i need
> > to go with for the stock pistons?
> >
> > Regards,
> > Danijel Krajisnik
> > 1994 R
> > T3/T4 .57 trim EWG w/EBC
> >
> > ________________________________
> >
> > Never miss a thing. Make Yahoo your homepage.
> >
>
> >
> > > _______________________________________________
> > Miatapower mailing list
> > [email protected]
> >
> http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
> >
>
> _______________________________________________
> Miatapower mailing list
> [email protected]
> http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
---------------------------------
Looking for last minute shopping deals? Find them fast with Yahoo! Search._______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
