Thanks, that clears it up. The console in question is a IIIC. Do you happen to have a photo of the console with the rear panel taken off just for reference? Bill
On Sun, Feb 14, 2010 at 10:38 PM, Armando Velazquez <[email protected]>wrote: > Hey Bill > > > Excuse my grammatical errors, , That's right, you need to disassemble the > console from the rear. Do not do on the top, since the entire section of > the bus, is connected by wires very small, hard, and easy to break. The > OpAmps of the output channel, are located next to the "odd-even" button. You > can try changing the opamp, if the problem persists, it may be the IC > NE5534AN (8 legs, small IC). Your series III is "IIIC", "IIIE" or > "IIIF"?...mine is "F" > Another option could be, replacing the resistors between the NE5534 and the > output channel, surely is a 100 ohms 1 W resistor. > I hope this helps, if not, let me know, we can try more things. > > Best regards from mexico. > > KB > > > *www.myspace.com/testaestudio* > *Cel: 4771351724* > > > > > > > Date: Sun, 14 Feb 2010 21:55:30 -0800 > > Subject: Re: NEOTEK: Series III repair question > > > From: [email protected] > > To: [email protected] > > > > Thanks for the reply Armando. That helps, but I'm still not exactly > > sure how to get to the track assign modules if I need to replace that > > op-amp, unless I misunderstood your response. Do I need to go in > > through the rear of the console to service the track assigns? > > Bill > > > > On Sun, Feb 14, 2010 at 8:32 PM, Armando Velazquez > > <[email protected]> wrote: > > > Hi Bill > > > > > > I have reconstructed all my S3...hiss, it's probably a burnt IC, > between the > > > chain channel> bus, could be either the 2.2mF capacitor, if the change, > > > nothing happens, you should check the bus module, also using TL084. To > > > access this module, you will have to carefully disassemble from behind > the > > > console, be careful, because a small cable connects all buses! If you > make a > > > mistake you can disable 1 or more channels! I hope this helps. If not, > feel > > > free to ask. > > > > > > Let me know, if you want to sell the S3, or if you know who sells S2. > > > > > > The best for you !!!! > > > > > > KB > > > > > > www.myspace.com/testaestudio > > > Cel: 4771351724 > > > > > > > > > > > > > > >> Date: Sun, 14 Feb 2010 19:01:03 -0800 > > >> Subject: NEOTEK: Series III repair question > > >> From: [email protected] > > >> To: [email protected] > > >> > > >> Hi, I'm new to the list - I searched the archives and didn't see where > > >> my question had been discussed before, so I'll ask it here, sorry if > > >> it has been a topic before. I have a friend with a Series III console > > >> with two bad output channels, 17 and 18. The inputs are all OK, and > > >> can be assigned to any channels other than 17 and 18. We can assign > > >> any input to 17 and 18 and all we get is hiss. I have the full > > >> schematics for the console, and it looks to me the problem is likely > > >> with the output amp on the track assign module. The question I have > > >> is how to best access that module, it doesn't appear as though it can > > >> be removed from the top of the console like the inputput module due to > > >> all the bus wires running between the modules. Any help with this > > >> would be greatly appreciated. Thanks in advance for any help. > > >> Bill Dunham > > >> San Jose CA. > > >> ------ > > >> > > >> View the list online at: > http://www.mail-archive.com/[email protected] > > >> > > >> You can unsubscribe at anytime by sending an email to > > >> mailto:[email protected] with "unsubscribe neotek" in the > message > > >> body. If you have any difficulties, or questions --please send an > email to > > >> mailto:[email protected]. > > >> > > >> The Neotek list is lovingly hosted by Catapult Web. Remember that any > > >> message or reply sent to the list will be automatically forwarded to > all > > >> subscribers. > > >> > > >> Vive Le Neotek! > > >> > > >> Thanks. > > > > > > ________________________________ > > > En Messenger están mis contactos con los que sí tengo contacto > > ------ > > > > View the list online at: > http://www.mail-archive.com/[email protected] > > > > You can unsubscribe at anytime by sending an email to mailto: > [email protected] with "unsubscribe neotek" in the message body. If > you have any difficulties, or questions --please send an email to mailto: > [email protected]. > > > > The Neotek list is lovingly hosted by Catapult Web. Remember that any > message or reply sent to the list will be automatically forwarded to all > subscribers. > > > > Vive Le Neotek! > > > > Thanks. > > ------------------------------ > ¿Te falta espacio para tus correos? Enciende tu hotness con > Hotmail<http://www.hotmailhotness.com.mx> >
