I have a IIIC from 1980 that was in Millbrook Sound for many years. All routing modules come out of the frame. 36 channels / 24 bus. I have had some work done on it recently, not all the channels work. I would be interested in selling this to someone who is serious. She weighs 850Lbs and is 9 and 1/2 feet wide.
I have some pictures and intend on taking a few more soon. Emilio China On Mon, Feb 15, 2010 at 10:58 AM, Sebago Sound <[email protected]> wrote: > Thanks, that clears it up. The console in question is a IIIC. Do you > happen to have a photo of the console with the rear panel taken off just for > reference? > Bill > > > > On Sun, Feb 14, 2010 at 10:38 PM, Armando Velazquez < > [email protected]> wrote: > >> Hey Bill > >> >> Excuse my grammatical errors, , That's right, you need to disassemble the >> console from the rear. Do not do on the top, since the entire section of >> the bus, is connected by wires very small, hard, and easy to break. The >> OpAmps of the output channel, are located next to the "odd-even" button. You >> can try changing the opamp, if the problem persists, it may be the IC >> NE5534AN (8 legs, small IC). Your series III is "IIIC", "IIIE" or >> "IIIF"?...mine is "F" >> Another option could be, replacing the resistors between the NE5534 and >> the output channel, surely is a 100 ohms 1 W resistor. >> I hope this helps, if not, let me know, we can try more things. >> >> Best regards from mexico. >> >> KB >> >> >> *www.myspace.com/testaestudio* >> *Cel: 4771351724* >> >> >> >> >> >> > Date: Sun, 14 Feb 2010 21:55:30 -0800 >> > Subject: Re: NEOTEK: Series III repair question >> >> > From: [email protected] >> > To: [email protected] >> > >> > Thanks for the reply Armando. That helps, but I'm still not exactly >> > sure how to get to the track assign modules if I need to replace that >> > op-amp, unless I misunderstood your response. Do I need to go in >> > through the rear of the console to service the track assigns? >> > Bill >> > >> > On Sun, Feb 14, 2010 at 8:32 PM, Armando Velazquez >> > <[email protected]> wrote: >> > > Hi Bill >> > > >> > > I have reconstructed all my S3...hiss, it's probably a burnt IC, >> between the >> > > chain channel> bus, could be either the 2.2mF capacitor, if the >> change, >> > > nothing happens, you should check the bus module, also using TL084. To >> > > access this module, you will have to carefully disassemble from behind >> the >> > > console, be careful, because a small cable connects all buses! If you >> make a >> > > mistake you can disable 1 or more channels! I hope this helps. If not, >> feel >> > > free to ask. >> > > >> > > Let me know, if you want to sell the S3, or if you know who sells S2. >> > > >> > > The best for you !!!! >> > > >> > > KB >> > > >> > > www.myspace.com/testaestudio >> > > Cel: 4771351724 >> > > >> > > >> > > >> > > >> > >> Date: Sun, 14 Feb 2010 19:01:03 -0800 >> > >> Subject: NEOTEK: Series III repair question >> > >> From: [email protected] >> > >> To: [email protected] >> > >> >> > >> Hi, I'm new to the list - I searched the archives and didn't see >> where >> > >> my question had been discussed before, so I'll ask it here, sorry if >> > >> it has been a topic before. I have a friend with a Series III console >> > >> with two bad output channels, 17 and 18. The inputs are all OK, and >> > >> can be assigned to any channels other than 17 and 18. We can assign >> > >> any input to 17 and 18 and all we get is hiss. I have the full >> > >> schematics for the console, and it looks to me the problem is likely >> > >> with the output amp on the track assign module. The question I have >> > >> is how to best access that module, it doesn't appear as though it can >> > >> be removed from the top of the console like the inputput module due >> to >> > >> all the bus wires running between the modules. Any help with this >> > >> would be greatly appreciated. Thanks in advance for any help. >> > >> Bill Dunham >> > >> San Jose CA. >> > >> ------ >> > >> >> > >> View the list online at: >> http://www.mail-archive.com/[email protected] >> > >> >> > >> You can unsubscribe at anytime by sending an email to >> > >> mailto:[email protected] with "unsubscribe neotek" in the >> message >> > >> body. If you have any difficulties, or questions --please send an >> email to >> > >> mailto:[email protected]. >> > >> >> > >> The Neotek list is lovingly hosted by Catapult Web. Remember that any >> > >> message or reply sent to the list will be automatically forwarded to >> all >> > >> subscribers. >> > >> >> > >> Vive Le Neotek! >> > >> >> > >> Thanks. >> > > >> > > ________________________________ >> > > En Messenger están mis contactos con los que sí tengo contacto >> > ------ >> > >> > View the list online at: >> http://www.mail-archive.com/[email protected] >> > >> > You can unsubscribe at anytime by sending an email to mailto: >> [email protected] with "unsubscribe neotek" in the message body. If >> you have any difficulties, or questions --please send an email to mailto: >> [email protected]. >> > >> > The Neotek list is lovingly hosted by Catapult Web. Remember that any >> message or reply sent to the list will be automatically forwarded to all >> subscribers. >> > >> > Vive Le Neotek! >> > >> > Thanks. >> >> ------------------------------ >> ¿Te falta espacio para tus correos? Enciende tu hotness con >> Hotmail<http://www.hotmailhotness.com.mx> >> > >
