Graham, which kind did you get? This type: http://c.shld.net/rpx/i/s/i/spin/image/spin_prod_206325301
This: http://tinyurl.com/nrhb8z9 Or this: http://www.toolsource.com/prod_medium/100652.jpg On Thu, Sep 10, 2015 at 12:23 PM, Graham Rogers <[email protected]> wrote: > It fits > > Sent from my iPad > > On Sep 10, 2015, at 11:18, Kyle Munz <[email protected]> wrote: > > Alexander, > Are you unable to fit two nuts on the stud? That is still the best way to > remove a stud if possible. What other guys are saying about the torch is > true and the next time I have any success with a screw extractor will be > the first time. The stud socket solution sounds best but if you don't have > enough room to get pliers in there that might not fit either. > > > -Kyle > > On Thu, Sep 10, 2015 at 9:47 AM, Allen Thomas <[email protected]> > wrote: > >> Have your guy be super careful with that torch, aluminum doesn't give any >> warning before it turns into a liquid. Its melting point is roughly 1200 >> degrees which is a lot lower than the 2000 degrees propane burns at, and >> mapp or acetylene burns hotter especially if mixed with oxygen. You should >> only need to get it up to the point where solder will melt on the stud (400 >> degrees), if you have some silver solder (which melts at 800 degrees) you >> can use it to test how hot your getting the stud. Like Kurt said by the >> time it is glowing red your already past 1200 degrees on the stud and >> probably dangerously close to melting it right out of the head. Also work >> the stud in both directions when trying to remove it, that one goes for any >> bolt/nut/screw that id difficult to remove. >> >> On Thu, Sep 10, 2015 at 10:17 AM, Kurt Nolte <[email protected]> >> wrote: >> >>> Don't get the stud glowing hot. Since the head is aluminum you can >>> soften the threads that way, you'll damage them pulling it out. >>> >>> I've had success in the past hitting bolts with a torch, then squirting >>> PB or WD at the base to quickly chill the stud/bolt, then hitting it with >>> the extractor. Not a lot of the WD, just one short squirt directly where >>> stud meets base. >>> >>> Kurt >>> On Sep 10, 2015 8:01 AM, "Alexander Press" <[email protected]> wrote: >>> >>>> I've heard heat is necessary for extraction no matter what rote you >>>> choose. I got a co worker coming to work with a torch today. So I'll keep >>>> everyone updated as to how that goes. Tool rental from auto zone I think >>>> will be my best bet. Thanks for that suggest. >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To post to this group, send email to [email protected]. >>>> Visit this group at http://groups.google.com/group/nighthawk_lovers. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Nighthawk Motorcycle Lovers!" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To post to this group, send email to [email protected]. >>> Visit this group at http://groups.google.com/group/nighthawk_lovers. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Nighthawk Motorcycle Lovers!" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> Visit this group at http://groups.google.com/group/nighthawk_lovers. >> For more options, visit https://groups.google.com/d/optout. >> > > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at http://groups.google.com/group/nighthawk_lovers. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at http://groups.google.com/group/nighthawk_lovers. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/nighthawk_lovers. For more options, visit https://groups.google.com/d/optout.
