Hi members, I tried to do the following to find out the error messages: Both systems with iscsitarget/open-iscsi initiator and open-iscsi initiator were up. On the open-iscsi initiator i had opened a terminal with command tail -f /var/log/messages and left it running And then i rebooted the server with iscsitarget/open-iscsi initiator
And all i could see were ocfs2_dlm node 0 leaves domain nodes in domain : 1 and then it hangs again so i had to manually hard reset the server I tried to boot with runlevel 2 but there were not much of a use because there were no specific error messages to this scenario, i Checked /var/log/messages and /var/log/boot.omsg But i'm still able to ping the open-iscsi initiator system on its hang. But when i try to rsh or ssh to the system, nothing happens. I haven't setup multipath yet. @mike I have setup ocfs2 file system on a partition(on secondary hard drive on iscsitarget/open-iscsi initiator box) which is being mounted as /u01/orcl on both boxes. So i think i have nbd(not sure if my setup is supposed to be called as nbd). When i tried rciscsitarget stop on iscsitarget/open-iscsi initiator box, both the iscsitarget/open-iscsi initiator box and open-iscsi initiator box hanged. Again a hard reset. How do i get a serial line or have a console hooked up somewhere on the box that hangs to get a trace? may be if you could send me a link on how to set this up? Appreciate all your sincere efforts to help me out. On Tue, May 12, 2009 at 12:24 PM, Mike Christie <micha...@cs.wisc.edu> wrote: > > sundar mahadevan wrote: >> Hi member, >> I run a test environment with 2 servers running opensuse 11.1(one has >> iscsitarget/open-iscsi initiator and other has open-iscsi initiator). >> Usually, I shutdown the open-iscsi initiator server first and then the >> other server with iscsitarget/open-iscsi initiator. But whenever i >> reboot the server with iscsitarget/open-iscsi initiator, the other >> server with open-iscsi initiator hangs completely even after the >> server with iscsitarget/open-iscsi initiator comes back after a >> reboot. Is this a normal behaviour? Because of the server hang, i'm > > So the open-iscsi initiator box is just connect to the > iscsitarget/open-iscsi one and all you do is reboot the > iscsitarget/open-iscsi box and the open-iscsi initiator box hangs? That > is not normal. > > Are you rebooting the open-iscsi initiator box at the same time? > > Do you have anything else in the stack like xen, md, multipath or nbd? > > Could you just try stopping the iscsi-target while the other box is > logged in? On the initiator only box you should see something a ping/nop > timing out and/or then see a conn error 1011 message. > > You can then start the iscsi target and the initiator box should log > back in. > > >> unable to check the logs and always have to go for a hard >> reset/shutdown. noob. help pls. >> > > You might want to attach a serial line or have a console hooked up > somewhere on the box that hangs. I think we might get a oops trace. If > you do send it here. > > > > --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to open-iscsi@googlegroups.com To unsubscribe from this group, send email to open-iscsi+unsubscr...@googlegroups.com For more options, visit this group at http://groups.google.com/group/open-iscsi -~----------~----~----~----~------~----~------~--~---